Molex 64003-0800 Manuale utente

RHT 1300 Hand Crimp Tool

Doc No. 64003-0800 Release Date: 07-21-03UNCONTROLLED COPY

Page 1 of 7

Revision: A Revision Date: 07-21-03

Hand Crimp Tool

Operating Instruction and Specifications Sheet

Part No. 64003-0800

Eng. No. RHT 1300

(Replaces 19284-0006)

FEATURES

A full cycle ratcheting hand tool ensures complete crimps

Long handles for comfortable crimping with reduced crimping force

A precision user-friendly terminal locator holds terminals in proper crimping position

SCOPE

Krimptite Flag Rings and Spades Terminals 14-16 AWG.

Testing

Mechanical

The tensile test, or pull test, is a means of evaluating the mechanical properties of the

crimped connections. The following charts show the specifications for various wire sizes.

The tensile strength is shown in pounds and indicates the minimum acceptable force to

break or separate the terminal from the conductor.

Wire Size (AWG)

*UL 486A

*UL - 486 A - Terminals (Copper conductors only)

The following is a partial list of the product part numbers and their specifications that

this tool is designed to run. We will be adding to this list and an up to date copy is

available on www.molex.com.

Wire Size: 14 –16 AWG 2.00 –1.30 mm²

Terminal No.

Terminal Eng No. (REF)

Wire Strip Length

Insul. Dia. Max.

In.

19041-0007

B-143-06

.266

6.75

N/A

19041-0009

B-143-08

.266

6.75

N/A

19041-0012

B-143-10

.266

6.75

N/A

19042-0004

B-148-06

.266

6.75

N/A

19042-0006

B-148-08

.266

6.75

N/A

19042-0008

B-148-10

.266

6.75

N/A

RHT 1300 Hand Crimp Tool

Doc No. 64003-0800 Release Date: 07-21-03UNCONTROLLED COPY

Page 2 of 7

Revision: A Revision Date: 07-21-03

Figure 2

TERMINAL

WIRE

TERMINAL

WIRE

CONDUCTO

PUNCH

Figure 3

CONDUCTO

ANVI

OPERATION

Open the tool by first closing the jaws sufficiently for the

ratchet mechanism to release.

Crimping Terminals

1. Slip the ring or spade of the flag terminal under the

locator tab and center the terminal barrel into the

conductor punch of the lower jaw. Make sure the open

side of the barrel is facing down, (See Figure 1).

2. Partially close the tool to hold the terminal in place

(See Figure 2).

Note: The tamper proof ratchet action will not release the tool until it has been fully

closed.

3. Insert the properly stripped wire into the terminal barrel (See Figure 2 and 3).

4. Now close the handle completely and release. The jaws will open when the tool has

fully closed.

5. Remove the crimped terminal. Inspect for proper crimp.

TERMINAL

JAWS

OPEN

Figure 1

LOCATO

RHT 1300 Hand Crimp Tool

Doc No. 64003-0800 Release Date: 07-21-03UNCONTROLLED COPY

Page 3 of 7

Revision: A Revision Date: 07-21-03

Maintenance

It is recommended that each operator of the tool be

made aware of, and responsible for, the following

maintenance steps:

1. Remove dust, moisture and other contaminants

with a clean brush, or soft, lint-free cloth.

2. Do not use any abrasive materials that could

damage the tool.

3. Make certain all pins; pivot points and bearing

surfaces are protected with a thin coat of high

quality machine oil. Do not oil excessively. The

64003-0800 (RHT-1300) was engineered for

durability, but like any fine piece of equipment it needs cleaning and lubrication for a

maximum service life of trouble-free crimping. A light oil, such as 30 weight

automotive oil used at the oil points shown in Figure 4, every 5,000 crimps or 3 months

will significantly enhance the tool life and ensure a stable calibration.

4. When tool is not in use, keep the handles closed to prevent objects from becoming

lodged in the crimping dies, and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not

force the handles open or closed. The tool will open easily by lifting the ratchet release

lever (See Fig.5).

How To Adjust Tool Preload (See Figure 5)

Over the life of the tool, it may be necessary to adjust tool handle preload force. Listed

below are the steps required to adjust the crimping force of the hand tool to obtain proper

crimp conditions:

1. Remove the screw and plastic cover

washer. Note the setting wheel

position.

2. Lift the setting wheel off the axle.

Turn the eccentric axle with a

screwdriver.

3. Turning the eccentric axle counter-

clockwise (CCW) will increase

handle force.

4. Replace the setting wheel to the

axle, aligning the nearest notch in

the setting wheel to the dowel pin.

5. Replace the plastic cover washer and screw.

6. Check the crimp specifications after tool handle preload force is adjusted.

PRELOAD

ADJUSTMENT

LOCKING

SCREW

1.00

RATCHET

RELEASE

LEVER

PUSH UP

PRELOAD

TEST

POINT

PRELOAD

TEST

POINT

Figure 5

Figure 4

LUBRICATION POINTS

(BOTH SIDES) LIGHT

OIL

(EVERY 3 MONTHS OR

5,000 CRIMPS)

RHT 1300 Hand Crimp Tool

Doc No. 64003-0800 Release Date: 07-21-03UNCONTROLLED COPY

Page 4 of 7

Revision: A Revision Date: 07-21-03

RHT 1300 Hand Crimp Tool

Doc No. 64003-0800 Release Date: 07-21-03UNCONTROLLED COPY

Page 5 of 7

Revision: A Revision Date: 07-21-03

NOT POSSIBLE TO PIN GAUGE

MEASURE A

CRIMPED UNINSULATED TERMINAL OR

A SLUG. *

*SOLDER, LEAD OR

Similar SOFT

METAL

Tool Calibration

A Certificate of Calibration (see last page) was supplied with the tool. To recalibrate this

Tool, Pin Gauge measurements should be taken in each conductor nest and compared to

this chart. The tool should be lubricated prior to recalibration to ensure consistent

measurements. Handle preload is factory set to 25-45 LBS. See How to Adjust Tool Preload

(see Figure 5) to recalibrate.

Nest Color Code

Wire Range

“X” Dimension Conductor Crimp

Crimp Inspection Marking

AWG

mm²

Mean

No Go

Blue

14 - 16

2.00 –1.30

.093

.089

.101

---

Caution: Repetitive use of this tool should be avoided.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best

quality materials. All vital components are long life tested. All tools are warranted to be

free of manufacturing defects for a period of 30 days. Should such a defect occur, we will

repair or exchange the tool free of charge. This repair or exchange will not be applicable

to altered, misused or damaged tools. This tool is designed for hand use only. Any

clamping, fixturing, or use of handle extensions voids this warranty.

Hand held crimping tools are intended for low volume, prototyping, or repair requirements

only.

RHT 1300 Hand Crimp Tool

Doc No. 64003-0800 Release Date: 07-21-03UNCONTROLLED COPY

Page 6 of 7

Revision: A Revision Date: 07-21-03

FOR SPRING

ACCESS

SWING

OPEN COVER

SCREW AND

PLASTIC

COVER FOR

HANDTOOL

PRELOAD

ADJUSTMENT

RATCHET

RELEASE

LEVER

M4 X 12LG

PAN

HEADSCREW

REPAIR KIT. ALL PARTS

REQUIRED FOR

REPAIR. (ONLY MAIN SPRING

SHOWN)

Figure 6

#4-40 X 1/8 LONG

BHCS

PARTS LIST

Item

Order No

Description

Quantity

64003-0800

Hand Crimp Tool

(Fig. 6)

64000-0076

Repair Kit (Springs, Pins and E-Rings)

63810-0000

Handle

64003-0870

Tooling Kit

64003-0875

Locator Assembly

Tooling Kit Only

64003-0802

Conductor Anvil

64003-0801

Conductor Punch

RHT 1300 Hand Crimp Tool

Doc No. 64003-0800 Release Date: 07-21-03UNCONTROLLED COPY

Page 7 of 7

Revision: A Revision Date: 07-21-03

Certificate of Calibration

Tool Order Number __________________

Tool Eng. Number ___________________

Tool Revision ___________________

Serial Number ___________________

Date of Manufacture__________________

Handle Load Range at 1 inch from the Tips =______________

Actual =_____________

Pin Gauge of Conductor Nest/Nests or Slug height if the nest is the “F” Crimp style.

Range Conductor Nest # 1 = ____________-- Actual = ______________

Range Conductor Nest # 2 = ____________-- Actual = ______________

Range Conductor Nest # 3 = ____________-- Actual = ______________

Technician ______________

Date of Calibration ______________

Calibration should be done every 5,000 cycles or 3 months.

Tools should be lubricated during this operation.

Molex Application Tooling Group

1150 E. Diehl Road

Naperville, IL 60563

Tel: (630) 969-4550;

Fax: (630) 505-0049

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali molex Utensili per crimpatura

molex

molex 69008-1100 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63801-8500 Manuale utente

molex

molex 63819-0900 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex MTA-100 Manuale

molex

molex AT 1610 Manuale utente

molex

molex 63827-2100 Manuale utente

molex

molex 63816-0800 Manuale utente

molex

molex 11-01-0185 Manuale utente

molex

molex 63811-6400 Manuale utente

molex

molex CS 150 Manuale utente

molex

molex CR60670B Manuale utente

molex

molex RHT-4754 Manuale utente

molex

molex 63819-1300 Manuale utente

molex

molex AT-200 Manuale

molex

molex 63827-0600 Manuale utente

molex

molex 63827-6070 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207128 Series Manuale utente

molex

molex CR60930B Manuale utente

molex

molex 64001-7400 Manuale utente

molex

molex AT 1991 Manuale utente

molex

molex 207129 Series Guida utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 2063528-1 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente

molex 64003-0800 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche