Molex CR60639B Manuale utente

CR60639B Hand Crimp Tool for “Min-Fit Jr.” Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 1 of 5

Revision: E Revision Date: 09-01-05

INSULATION

CRIMP

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

HAND CRIMP TOOL

Operating Instruction and

Specification Sheet

Order No. 11-01-0198

(CR60639B)

FEATURES



Small handle spread which make this style tool ideally suited for end users



Ratchet with safety release that ensures consistent performance



A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position

SCOPE

Wire Size Insulation Diameter Strip Length

Terminal Series No. AWG mm² mm In. mm In.

5556-T2 22 - 28 0.35-0.08 0.90-1.80 .035-.071 2.79-3.30 .110-.130

5558-T2 22 - 28 0.35-0.08 0.90-1.80 .035-.071 2.79-3.30 .110-.130

DEFINITION OF TERMS

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.

CR60639B Hand Crimp Tool for “Min-Fit Jr.”Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 2 of 5

Revision: E Revision Date: 09-01-05

Figure 2

CONDITIONS:

After crimping, the conductor profiles should measure the following (see notes on page 4).

Punch Width (Ref)

Wire Size Cond. Crimp Height

(Ref) Cond. Ins.

Pull Force Min. Profile

Terminal Series No.

AWG mm2mm In. mm In. mm In. N Lb. A B

5556-T2 22 0.35 0.76-0.86 .030-.034 1.42 .056 1.68 .066 40.0 9.00 X

5556-T2 24 0.20 0.69-0.79 .027-.031 1.42 .056 1.68 .066 31.1 7.00 X

5556-T2 26 0.12 0.64-0.74 .025-.029 1.42 .056 1.68 .066 22.2 5.00 X

5556-T2 28 0.08 0.61-0.71 .024-.028 1.42 .056 1.68 .066 13.3 3.00 X

5558-T2 22 0.35 0.76-0.86 .030-.034 1.42 .056 1.68 .066 40.0 9.00 X

5558-T2 24 0.20 0.69-0.79 .027-.031 1.42 .056 1.68 .066 31.1 7.00 X

5558-T2 26 0.12 0.64-0.74 .025-.029 1.42 .056 1.68 .066 22.2 5.00 X

5558-T2 28 0.08 0.61-0.71 .024-.028 1.42 .056 1.68 .066 13.3 3.00 X

OPERATION

Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will release the handles,

and the hand tool will spring open.

Crimping Terminals

1. Lift the locator blade and place the terminal into the correct die

profile (A or B), release the locator blade. Not all tools are

equipped with a locator or locator blade.

2. Partially close the tool until the terminal is held in place, (See

Figure 1). If the insulation diameter is too large to do this, then

place the insulation down into the terminal before closing the

tool.

TERMINAL

PRE-STRIPPED WIRE

Figure 1

CR60639B Hand Crimp Tool for “Min-Fit Jr.”Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 3 of 5

Revision: E Revision Date: 09-01-05

Figure 3

3. Place a wire into the terminal and up against the locator blade, (See Figure 2).

On tools without locators line the wire up with the conductor and insulation

grips visually.

4. Close the tool until the ratchet releases, (See Figure 3).

5. Lift the locator blade or wire stop up.

6. Carefully remove the crimped terminal.

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible

for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil

excessively.

4. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in

a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open

easily by lifting the ratchet release lever (See Figure 4).

How To Adjust Tool Crimp Force (See Figure 4)

It may be necessary over the life of the tool to adjust tool-crimping force. Listed below are the steps required to adjust the crimping

force of the hand tool to obtain proper crimp conditions:

1. Remove the screw and washer. Located over the adjustment ring.

2. Lift the adjusting ring slightly, off of the locating pin.

3. Turn the adjusting ring in the desired direction (L= less force, T= more force) to increase or decrease crimp pressure.

4. Press the adjusting wheel flat against the tool and engage the locking pin.

5. Replace the washer and screw.

6. Check the crimp specifications after tool crimp force is adjusted.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long

life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we would

exchange the tool free of charge. This will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use

only. Any clamping, fixturing, or use of handle extensions voids this warranty.

CR60639B Hand Crimp Tool for “Min-Fit Jr.”Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 4 of 5

Revision: E Revision Date: 09-01-05

Hand held crimping tools are intended for low volume, prototyping, or repair requirements only.

CAUTION: Repetitive use of this tool should be avoided.

Notes:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height, however crimp force is adjustable (See instructions above). Variations in tools,

terminals, wire stranding and insulation types may affect crimp height.

3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes.

4. Molex does not repair hand tools (see warranty above) The replacement parts listed are the only parts available for repair. If the

handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no influence from the insulation

crimp. The insulation should be stripped long (1/2 in.) so the insulation grips on the terminal do not grip the wire insulation or the

conductor. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping and crimp testing.

6. Molex does not certify crimp hand tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.

CR60639B Hand Crimp Tool for “Min-Fit Jr.”Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 5 of 5

Revision: E Revision Date: 09-01-05

M4 NUT

RATCHET

RELEASE LEVER

ADJUSTMENT

RING

LOCATOR

BLADE

Figure 4

M4 X 18LG BHCS

PARTS LIST

Item Number Order Number Description Quantity

1 11-11-0377 Locator Assembly** 1

2 11-11-0324 Spring (Main) 1

3 11-11-0320 Spring (Ratchet) 1

** Not all tools are equipped with a locator or locator blade.

Molex Application Tooling Group

1150 E. Diehl Road

Naperville, IL, 60563

Tel: 630-969-4550

Fax: 630-505-0049

Visit our Web site at http://www.molex.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali molex Utensili per crimpatura

molex

molex 63825-6770 Manuale utente

molex

molex 43178 Series Manuale utente

molex

molex 4D Guida utente

molex

molex 50837 Manuale utente

molex

molex CR60930B Manuale utente

molex

molex 35465 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63828-1900 Manuale utente

molex

molex 63827-0600 Manuale utente

molex

molex 63811-1200 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex CR60927A Manuale utente

molex

molex CR5974 Manuale utente

molex

molex 63825-7570 Manuale utente

molex

molex 64001-7400 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex AT 1991 Manuale utente

molex

molex 63823-8000 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 11-01-0185 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 2063528-1 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente

molex CR60639B Manuale utente

Manuali Utensili per crimpatura popolari di altre marche