Mongoose JS500 Manuale utente
Manual for JS500
MANUAL for JS500
INTRO Manual for JS500
CONTENTS
The contents could be changed to enhance the performance without notice.
2
Power Cable
(3 Pin Connector Type)
Main Body 32GB Micro SD USB Wi-Fi
Dongle
External
GPS
Receiver
2nd Cam HD
and cable
Options extra cameras
Front FHD Cam
and cable
Manual for JS500
INTRO
PART DESCRIPTIONS
Status LED LEDs showing system operating status
Front Cam
Port Front external camera connecting port (SMBL)
Cam 1 Rear external camera connecting port
Cam 2 Rear external camera connecting port
GPS External GPS Receiver connecting port
Power Power Jack Port
Wi-Fi Port Wi-Fi Port /Connecting USB Wi-Fi Dongle here
Sound
Speaker
Hole
I/O PortData Input & Output cable connecting port
SD Card Slot SD Card Slot
ResetInitialize the system
3
EXTERIOR
INTRO Manual for JS500
INSTALLATION
1. Please set configuration and make sure JS500 is working correctly
before installation.
2. Please check and confirm the proper spot before installation.
3. JS500 is designed as hidden installation type on small size
It can be installed in Glove box, Bonnet, Dash Board and under Driving
seat...etc.
1. Please check and confirm the proper spot for external camera before
installation.
Small size external camera also can be installed with special 3M double side
from tape on various spots such as window, roof and room mirror...etc.
4
Before Install
N o t e
INTRO Manual for JS500
INSTALLATION
Insert Micro SD
Insert Micro SD card into the SD card slot on the main unit. Before
start the system, Micro SD card must be inserted. Please be sure to
insert Micro SD Card correctly as the image.
Connect Front Camera Cable into Front Camera Cable port on side of the
mina unit as the image.
Front Camera must be connected correctly to the main unit.
Otherwise, the system is not working.
The other side of cable should be connected to the external camera.
Connect Rear Camera Cable
Connect Rear Camera Cable into Rear Camera Cable port on side of
the main unit as the image.
The other side of cable should be connected to the external camera.
NOTE
JS500 is using format free file system to provide more secure file system
and extend SD card life.
So, SD card must be formatted by JS500 exclusive PC viewer prior to
use .
Connect Front Camera Cable
5
INTRO Manual for JS500
INSTALLATION
Connect GPS Receiver Cable
Connect GPS Jack into GPS port as the image.
Push the camera jack and rotate it to fit and fix the jack.
Connect Power Cable
After above installation process, please connect Power cable to the
Power Port.
When Power comes in, Status LED will lighting or blinking. (Refer to
the next page for more details.)
6
INTRO Manual for JS500
INSTALLATION
GPS & WiFi Working Status LED
- When GPS is connected correctly and activated, Green LED will be
blinking at 3 second interval.
Power LED
- When Power is connected correctly, Red LED will be ON
Recording Working Status LED
- When camera is connected and recording correctly, Green LED will be
blinking at 2 second interval. (Event 1 sec interval)
Adjust Camera Angles
Records video for several minutes and check the camera angles
through the video view angles.
You can play the recorded video on your Smart Phone or PC Viewer.
7
INTRO Manual for JS500
DIRECT BATT. CONNECT
BATT(+)
ACC(+)
GND
Red Wire BATT(+)
Connects Red wire of Power cable provided to regular Car Power in
Fuse Box.
(Ex : Emergency Lights, Interior Lights, Tale Lights...etc.)
Yellow or White Wire ACC(+)
Connects Yellow or White Wire of Power Cable provided to the fuse
that power comes in when engine is started.
(Ex : Cigar Lighter, Audio)
Black Wire
This is Ground. Connects it with metal parts of vehicle, such as metal
bolt, screw...etc. as the image.
※ Wire color may be changed by circumstances of wire provider.
8
START Manual for JS500
STATUS LED
Starts System
When connected to power , "Red” , "Green“ & “Blue” LEDs are on while the
system is booting up. ( Voice : System is starting)
Closes System
If you stop using the system and disconnect power, it records additional 1
seconds, and three LEDs are turned On. And three LEDs goes to Off when the
system is completely shut down. Note) Micro SD Card memory must be
removed after LEDs are Off.
Recording Status LED
When “GRN" LED is Blinking at every 2 second, it indicates that recording is in
progress. When the normal event occurs “GRN" LED will blink at every 1 second .
GPS Reception
When “BLU" LED is ON, it indicates that the GPS connected, When GPS is 3D fix,
“BLU” LED blinking once at 3 second intervals
9
START Manual for JS500
STATUS LED
LED on Each Mode
Normal Mode
- “RED” LED is always On.
- ”GRN” LED indicates that recording is in progress.
When the normal record mode , LED is blinking once at every 2 seconds.
When the normal event occurs, LED is blinking once at every 1 second.
Parking Mode
-“RED" LED is blinking once ( 1 second ) at every 2 seconds
-“GRN” LED is blinking once during 20 seconds, when the Parked impact or motion
event occurs.
Indice
