Morse 26 Manuale utente

The Specialist In Drum Handling Equipment

Drum Pumps

[email protected] 103 Kuhn Rd.

Syracuse, NY, 13208 U.S.A.

morsedrum.com (315) 437-8475

CONTENTS

Page

Receiving Procedures. . . . . . . . . . . . . . . . . . . . 1

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information. . . . . . . . . . . . . . . . . . . . . 1 - 3

Description. . . . . . . . . . . . . . . . . . . 3

Operating Instructions. . . . . . . . . . . . . . .. . . . . 4

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . 5

Handling Flammable Liquids. . . . . . . . . . . . . 6

Parts List and Diagram. . . . . . . . . . . . . . . . . . 7 - 8

Operator’s Manual

for Morse Drum Pump Models

26, 27-1AE, 27-4AV,

28-5BV and 28-6BE

Receiving Procedures

Every Morse drum handler is inspected prior to shipping. However,

damage may be incurred during transit.

Check for visible damage. If you choose to accept damaged•

freight, always sign noting the damage on the Bill of

Lading.

Document the damage and have the truck driver sign. We•

recommend keeping a digital camera at your receiving dock

for this purpose.

Open packages expeditiously to check the condition of the•

goods. There is only a 24 hour window to notify the carrier

of any concealed damage.

Immediately• report all damage to the shipping company!

Then you may contact Morse for assistance with your

freight claim.

Morse Manufacturing will not be held responsible for any•

damaged freight that is not signed for as damaged.

Depending on model number and options ordered the•

following parts are shipped loose in the carton and should

be checked before destroying the carton and packaging

material. See the drawing in page 7 to help identify these

parts.

1 bung adaptor (item 32)1.

1 clamp (item 31)2.

1 hose (item 17), complete with: 1 hose adaptor3.

(item 21)

1 nozzle (item15), 2 hose clamps (item16)4.

1 suction tube (item 36)5.

1 extension tube (item 34)6.

1 coupling (item 35)7.

1 discharge spout8.

Limited 1 Year Warranty

Morse drum handling equipment is guaranteed against defects in

workmanship or materials for one year when used properly within

its rated capacity. Warranty does not cover wear from normal use

or damage from accident or abuse. Motors and other purchased

parts carry the warranties of their manufacturers. For warranty

claims, contact your Morse Dealer to obtain a return authorization

number, and for return freight advice. Return freight must be

prepaid.

In all instances, liability is limited to the purchase price paid or to

repairing or replacing the product. Customer assumes liability for

anymodications,unauthorizedrepairsorpartssubstitution.

Safety Information

While Morse Manufacturing Co. drum handling equipment is

engineeredforsafetyande󰀩ciency,ahighdegreeofresponsibility

must be placed upon the machine operator to follow safe practices,

based primarily on common sense, upon which true safety

depends.

Failure to follow the safety precautions in this manual can result in

personal injury or property damage. Observe the same precautions

as with similar machinery where carelessness in operating or

maintenance is hazardous to personnel. Carefully read the safety

precautions below and throughout this manual.

Review the Material Safety Data Sheet(s) for the material(s) in

the drum(s) and take all necessary precautions. Safety shoes,

work gloves, hard hat and other personal protective devices are

recommended.

Prior to initial use, inspect all moving parts. Inspect pump for

proper operation. Perform necessary test, inspections, operator

training, etc.

The Specialist In Drum Handling Equipment

Drum Pumps

morsedrum.com

Safety Information (continued)

DANGER - Indicates a situation which, if not avoided, will result in serious injury or death.

This signal word is limited to the most extreme situations.

WARNING - Indicates a situation which, if not avoided, could result in serious injury or

death.

CAUTION - Indicates a situation which, if not avoided, can result in damage to the machine.

WARNING -DoNotModifytheUnit.UndernocircumstancesshouldanymodicationsbemadetotheMorse

machinerywithoutfactoryauthorization.Anymodicationsmayvoidthewarranty.Thismachinewasdesignedto

performaspecicjobandalterationsmayresultininjurytooperatorormachine.

WARNING -NoLooseFittingClothing.Wearclose-ttingclothingandsafetyequipmentappropriatetothejob.

Loosettingclothingmaybecomecaughtonthemachineryandcauseseverepersonalinjury.

CAUTION - Wear safety shoes with non-slip soles and hard toe protection.

CAUTION -DONOTallowdrumtoimpactonoor,ground,ordumpingstation,etc.

WARNING - Verify the chemical compatibility of the materials of your pump with the liquid you want to pump. If

you are uncertain regarding chemical compatibility, contact your dealer for applications assistance and request a

copy of our Corrosion Resistance Charts. Do not use a pump that is not chemically compatible with the liquid you

intendtopumporseriousbodilyinjury,death,re,explosionorenvironmentaldamagecouldresult.SeeChemical

Compatibility Chart online.

IMPORTANT - Refer to Chemical Resistance Data Chart for compatibility of materials. Always wear protective

safety clothing such as gloves, apron, goggles.

DANGER -Whenpumpingammableorcombustibleliquidsfromonecontainertoanother,bothcontainersmust

bee󰀨ectivelybondedandgroundedtopreventdischargeofsparksorstaticelectricitywhichcouldcauseexplosion

and bodily harm.

WARNING: This product can expose you to chemicals including cobalt, titanium dioxide, and 2-methylimidazole,

which are known to the State of California to cause cancer, and bisphenol-A, which is known to the State of

California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Specialist In Drum Handling Equipment

Drum Pumps

morsedrum.com

The extension tubes are threaded at both ends. Extra extension

tubes and couplings may easily be used for deeper vessels such

as tanks. Maximum suction lit is 15 feet.

A 55-gallon drum on end1.

requires 1 extension tube, 1

coupling and 1 suction tube

threaded together.

To use the side bung hole2.

on a 55-gallon drum, thread

together one extension

tube, one coupling and a 5”

length of suction tube. The

plastic tube can easily be

cut with a hacksaw. Make

the cut at an angle. DO

NOT CUT THE THREADED

END.

For 275 gallon tanks, thread3.

together two extension

tubes and one suction tube.

Description

If you have not checked the chemical compatibility of yourA.

pump with the liquid, do it now before using the pump! The

pump is equipped in one of several ways. Compare your

model number with the model number chart immediately

on page 5. This will tell you what materials make up your

pump. Consult the factory for any chemical applications. A

chemical resistance chart is packed with the pump. Chemical

Compatibility Chart is also online.

The pump handle can be easily positioned either up for normalB.

use, or down, allowing the pump to be elevated. This would be

convenient for example when pumping from a truck mounted

drum or barrel. See Pump Operating Instructions step F on

page 4.

A siphon breaker is built into the pump discharge. ThisC.

prevents siphoning from the drum if the hose drops from

its hanger. It also allows the hose to drain completely after

pumping.

The barrel is vented by 4 relief channels molded into the bungD.

adaptor. This prevents drawing a vacuum in the barrel.

ThesuctiontubeandextensiontubesuppliedarecuttotaE.

standard 55-gallon drum. The suction tube has a bevel cut at

one end and is threaded at the other end.

Figure 1

Safety Precautions

This manual contains important information for the safe andA.

proper operation of this pump. Read it THOROUGHLY before

operating or installing the pump.

USE ONLY ORIGINAL FACTORY REPLACEMENT PARTS.B.

Whenpumpingammableliquids,ensureadequateventilationC.

to prevent explosive build up of fumes. Pumping should

alwaysbedoneina“NOSMOKING”area.Approvedre

extinguishers,ingoodcondition,shouldbeavailableforre

suppression.

Containersholdingammableliquidsshouldbegrounded,andD.

portable containers bonded, to prevent explosion hazards from

static electricity charges. See page 6.

Operators should be properly instructed on operatingE.

procedures and safety precautions.

DonotusetorchesorapplyreorametothispumpforanyF.

reason.

When pumping corrosives use personal protection such asG.

rubber gloves, aprons, eye shields and adequate ventilation.

Consult chemical manufacturer for additional cautions.

Donotovertightennonmetallicthreadedttings.OnefullturnH.

past hand tight is usually enough to prevent leakage. One roll

ofteontapeisprovidedandshouldbeusedonallthreaded

joints.

Inspect the siphon breaker regularly to ensure properI.

operation. To test siphon breaker, lay hose on ground with

nozzle in a suitable container to hold the liquid. Operate the

handleuntilliquidowsfromthenozzle.Stoppumping:the

hoseshoulddrainandtheowstop.Ifowcontinueswithout

moving the handle, place the nozzle in its hanger to stop the

ow.Theninspectthesiphonbreakerventforblockageor

freezing. Flush the vent with water, or if pumping petroleum

products, use clean product.

TO PREVENT SPILLING LIQUID WHEN REMOVING PUMP

FROM BARREL, OBSERVE THE FOLLOWING PRECAUTIONS:

Straighten discharge hose and hold it below the pump1.

discharge. Allow hose to drain into a container.

Loosen stainless steel clamp (item 31).2.

Pull pump from bung adaptor and allow suction tube to3.

drainbacktothebarrel.Laypumpatwithhandleup.Place

container under nozzle. Operate handle until liquid is clear

from pump housing.

Allow discharge hose to drain. Place the hose nozzle in4.

its hanger. If pump will not be installed in a new barrel,

anycausticorcorrosivechemicalsshouldbeushedwith

fresh water internally and externally to prevent personal

injury during handling. ANY PUMP USED TO TRANSFER

FLAMMABLE LIQUIDS MUST BE STORED IN A WELL

VENTILATED AREA AFTER USE.

Figure 3

The Specialist In Drum Handling Equipment

Drum Pumps

morsedrum.com

Pump Operating Instructions

FOR EASY INSTALLATION FOLLOW THESE STEPS IN THE

ORDER SHOWN.

Screw the bung adaptor into the drum or barrel. Be sure not toA.

overtighten (Refer to Safety Precautions step H on page 3).

Install supplied clamp loosely around bung adaptor.B.

Thread appropriate length of suction tube and extensionC.

tube(s)intopumpsection.Useteontapeprovided(Referto

Safety Precautions step H on page 3).

Install pump and tubing into bung adaptor by pushing straightD.

downrmly.Housingwillsnapinplace.Tightentheclamp

(item 31). Screw hose and adaptor or discharge spout into

pump body.

Caution: When pumping from a lined drum, order part itemE.

58-0069.Thisisaexiblesuctiontubetopreventdamageto

the liner.

The handle position can be changed with the following steps.F.

Remove hairpin clip (item 6) from clevis pin (item 7).1.

Remove clevis pin from housing to free links (item 8).2.

With links clear of housing, rotate handle 1/2 turn to new3.

position.

Install clevis pin through the links and the opposite hole in4.

housing.

Install hairpin clip through the hole in the clevis pin.5.

Ensuretheatwasher(item4)isinstalledbetweenthe

hairpin clip and the link.

CAUTION: This hole is used for security lock only.6.

Remove hose from hanger and place nozzle in container.G.

Operate handle to prime the pump. 3-6 strokes are required under

most conditions. After the pump is primed it will deliver about one

gallon for every four full strokes (backward and forward).

Two Position Pump Handle

Trouble Shooting Guide

A. pump will not prime

Clogged suction. Check that the suction tubes are clear and1.

thatthescreenlterisnotdirtyorclogged.Useapairof

needlenosepliersorasti󰀨pieceofwiretopullthesuction

screen from housing. Clean it, if necessary, and push it gently

backintothehousingorwithangerorbluntrod.

Air leakage. Check that the connection to housing, extension2.

tube and suction tube are threaded tightly and sealed with

teontape(RefertoSafetyPrecautionsstepHonpage3).

Pistonleakage.Verifythattheteonringtssnuglyinbore3.

and is not cut or excessively worn.

Valve leakage. Inspect poppet valves for weak springs4.

or clogging. If pump was recently disassembled VERIFY

PROPER POSITION OF VALVE SEATS (Refer to

Maintenance step B.1. on page 5).

Gasketleaks.Inspectfortorngasket(item18),poortor5.

loose coverplate bolts (item 20).

B. Not Enough Flow

Check items A. 1-5.1.

Check discharge hose for clogging or pinching. Verify that the2.

nozzle is not clogged.

Check that piston is travelling its full stroke and the linkage3.

has not bound or jammed.

The Specialist In Drum Handling Equipment

Drum Pumps

morsedrum.com

Maintenance

Use only original factory replacement parts

A. Disassembly

Remove hose (item 17) from housing. Unscrew suction and/or1.

extension tubes (items 34 and 36).

Remove hex nuts (item 22) and screws (item 20) from2.

housing. Remove cover plate and gasket (items 19 and 18),

being careful not to damage the gasket.

Remove large and small valve assemblies (items 24 and3.

23) and inspect for broken or weak springs, or damaged or

clogged valves.

Remove hairpin clip (item 5), washer (item 4) and clevis pin4.

(item 3) which hold the handle (item 2) to the piston rod.

Removehairpinclip(item6),atwasher(item4)andclevis

pin (item 7) from links (item 8) at the pump housing (item 37).

Remove pin (item 3) from piston rod and set handle aside.

Slide piston assembly (item 28) from the housing.

Inspectteonring(item30)inpistongroove.Itmustextend5.

about 1/32nd above the edge of the piston to seal properly. If

theringiswornushwiththepistonedgeitmustbereplaced.

Whenremovingtheteonringbecarefulnottodamage

the piston if tools are being used. Always replace the O-ring

(item29)whenreplacingtheteonring.TherubberO-ringis

compressed over time, reducing its ability to seal.

Inspect piston bore in housing (item 37) for wear. Any gouging6.

or scraping would indicate that the liquid being pumped

containsabrasives.Replacethehousingandteonringifthe

surfaces are gouged or worn.

Remove the two screws (item 9) that hold the retaining plate7.

(item 10) to the housing. Remove plate to expose piston rod

O-ring (item 11). Replace O-ring if worn.

B. Reassembly

Install the two small valve assemblies (item 23) in the housing1.

rst,thenthetwolargeassemblies(item24).Thereisasmall

tabmoldedintothevalveseatswhichtsaguidechannel

in the housing. This prevents installing the valve seats

backwards. If the tabs are broken, please note the following.

The suction valve seats (lower two) should have theira.

springs facing each other when installed.

The discharge valve seats (upper two) should haveb.

springs facing away from each other.

Install piston rod O-ring (item 11). Install retainer plate (item2.

10) with the groove facing AWAY from the pump housing.

Ensurepiston(item28)hasO-ring(item29)andteonring

(item30)installed.Teonringwillstretchenoughtoinstall

by hand (tools may damage the piston). Slide piston rod into

housing.Theteonringwillcatchontheedgeofthehousing

while pushing the piston into the bore. To help seat the ring,

turn piston slowly while pushing ring into the grove with

ngers.DONOTFORCEPISTON.

Inspect the cover plate gasket (item 18) for damage.3.

Lay coverplate and gasket on housing and install screws4.

(item20)andhexnuts(item22).Tightenrmlyenoughto

compress gasket.

Install short clevis pin (item 3) through the piston rod and5.

handle securing with washer (item 4) and hairpin clip (item 5).

Installclevispin(item7),atwasher(item4)andlinks(item

8) at the pump housing.

Install hose and suction extension tubes as required. Refer to6.

Safety Precautions step I. on page 3, and Description step E.

on page 3.

General Guide to Morse Drum Hand Pump Applications

Pump

Model item

Construction

(All have some

T316SS)

O-Ring

Mtl.

Gasket

Mtl. Hose Mtl. Suction

Tube

Compatible Liquids*

(General Guide)

26 polyester viton cork-nitrile PVC polyester petroleum products, lube oils*

27-1AE polyester EPDM EPDM EPDM polyester methyl alcohol, ethyl alcohol*

27-4AV polyester viton viton cross linked

polyeth. polyester some napthas*, some aromatics*

28-5BV ryton viton viton cross linked

polyeth. teon some chlorinated solvents, acids,

aromatics, xylene*

28-6BE ryton EPDM EPDM EPDM teon some acids, caustics, ketones,

acetates*

* NOTE: General guide only. Final determination of suitability for use intended or manner of use is responsibility of the user.

ConsultMorseforadviceonspecicliquidsiftheyarenotshownhere.Pleasefurnishchemicalnames.

** NOTE: Chemicals may be hazardous. It is the user’s responsibility to take appropriate safety and protective measures.

Specicationssubjecttochangewithoutnotice.

CAUTION: Chemical compatibility of a pump should be CHECKED FOR EACH LIQUID BY CHEMICAL NAME.

See Chemical Compatibility Chart online.

The Specialist In Drum Handling Equipment

Drum Pumps

morsedrum.com

General Safety Information for Handling Flammable and Combustable Liquids

WARNING -Whenusingahandpumptollcans,drumsorotherportableorxedcontainerswith

ammableorcombustibleliquidssuchasgasoline,bothcontainerbeingpumpedfromandthe

containerbeingpumpedtomustbee󰀨ectivelyBONDEDandGROUNDEDtopreventdischargeof

sparks of static electricity which could cause explosion.

BONDING is the electrical interconnection between containers (such as a drum and a receiving can).

Bonding must be completed BEFORE pumping begins. See diagrams below.

GROUNDING is the electrical connection between a container and a “constant ground”. A “constant

ground” would be a metal pipe or rod in contact with the earth. An underground tank and piping

connected to it would be inherently grounded by nature of the installation. See diagrams below.

BothBONDINGandGROUNDINGofcontainersofammableliquidsarerequiredunderU.S.

Government OSHA regulations and National Fire Protection Association Code 77, Static Electricity.

Consultfactoryforspecicliquidhandlingrecommendations.

High quality BONDING and GROUNDING wires are available through drum accessory suppliers.

The Specialist In Drum Handling Equipment

Drum Pumps

morsedrum.com

Drum Pump Repair Kits (Valves and Gaskets)

Pump Model # Repair Kit # Description

26 5867-P Cork/NitrileGasket,VitonO-Rings,PolyesterValves,TeonPistonRing

27-1AE 5869-P EPDMGasketandO-Rings,PolyesterValves,TeonPistonRing

27-4AV 5866-P VitonGasketandO-Rings,PolyesterValves,TeonPistonRing

28-5BV 5865-P VitonGasketandO-Rings,HalarValves,TeonPistonRing

28-6BE 5868-P EPDMGasketandO-Rings,HalarValves,TeonPistonRing

The Specialist In Drum Handling Equipment

Drum Pumps

morsedrum.com

ITEM QTY. MODEL PART # DESCRIPTION

1 1 ALL PUMP MODELS 1049-40 KNOB, POLYPROPYLENE, PAC

2 1 ALL PUMP MODELS 1050-01 HANDLE ASM, PUMP, PAC

3 1 ALL PUMP MODELS 1053-00 PIN, CLEVIS 5/16 X 1-1/8, PAC

4 4 ALL PUMP MODELS 1380-90 WASHER, FLAT, NYLON, PAC

5 2 ALL PUMP MODELS 1379-00 CLIP, HAIRPIN, SMALL, PAC

6 1 ALL PUMP MODELS 1027-00 CLIP, HAIRPIN, LARGE, PAC

7 2 ALL PUMP MODELS 1031-00 PIN, CLEVIS, 5/16 X 1-1/4 PAC

8 2 ALL PUMP MODELS 1052-00 LINK, PLATED STEEL, PAC

9 2 ALL PUMP MODELS 1348-10 SCREW, 10-14 X 3/4 SS, PAC

10 1 26, 27-1AE, 27-4AV 1032-30 PLATE, RETAINING, PE, PAC

10 1 28-5BV, 28-6BE 1032-90 PLATE, RETAINING, HALAR, PAC

11 1 27-1AE, 28-6BE 1030-72 O-RING, PISTON ROD, EPDM PAC

11 1 26, 27-4AV, 28-5BV 1030-73 O-RING, PISTON ROD, VITON PAC

14 1 27-1AE, 28-6BE 1040-72 VACUUM BREAKER, EPDM, PAC

14 1 26, 27-4AV, 28-5BV 1040-73 VACUUM BREAKER, VITON, PAC

15 2 26, 27-1AE, 27-4AV 1325-30 NOZZLE, NO-LEAD, PE, PAC

15 1 28-5BV, 28-6BE 1325-90 NOZZLE, NO-LEAD, HALAR, PAC

16 2 ALL PUMP MODELS 1044-12 CLAMP, HOSE, CRIMPED, SS, PAC

17 1 26, 27-1AE, 27-4AV 1342-02 HOSE, PVC W/ PE NOZZLE, PAC

17 1 28-5BV, 28-6BE 1342-92 HOSE, PVC, HALAR NOZZLE, PAC

17 1 26, 27-1AE, 27-4AV 1342-04 HOSE, NITRILE, PE NOZZLE, PAC

17 1 28-5BV, 28-6BE 1342-94 HOSE, NITRILE, HALAR NOZZLE

17 1 26, 27-1AE, 27-4AV 1342-05 HOSE, EPDM W/ PE NOZZLE

17 1 28-5BV, 28-6BE 1342-95 HOSE, EPDM, HALAR NOZZLE, PAC

17 1 26, 27-1AE, 27-4AV 1342-07 HOSE, CLPE W/ PE NOZZLE, PAC

17 1 28-5BV, 28-6BE 1342-97 HOSE, CLPE, HALAR NOZZLE, PAC

18 1 27-1AE, 28-6BE 1204-72 GASKET, COVERPLATE, EPDM, PAC

18 1 27-4AV, 28-5BV 1204-73 GASKET, COVERPLATE, VITON, PAC

18 1 26 1204-90 GASKET, COVERPLATE, CORK, PAC

19 1 26, 27-1AE, 27-4AV 1209-30 COVERPLATE, PE, RED, PAC

19 1 28-5BV, 28-6BE 1209-60 COVERPLATE, RYTON, BLACK, PAC

20 11 26, 27-1AE, 27-4AV 1206-00 SCREW, 1/4-20 X 2, PAC

20 11 28-5BV, 28-6BE 1206-10 SCREW, 1/4-20 X 2 SS, PAC

21 1 26, 27-1AE, 27-4AV 1214-30 ADAPTER, HOSE, PE, 60DEG, PAC

21 1 28-5BV, 28-6BE 1214-90 ADAPTER, HOSE, HALAR 60DEG PAC

22 11 26, 27-1AE, 27-4AV 0721-00 NUT, 1/4-20 HEX, PLATED, PAC

ITEM QTY. MODEL PART # DESCRIPTION

22 11 28-5BV, 28-6BE 0721-10 NUT, 1/4-20 HEX, SS, PAC

23 2 27-1AE 1340-02 VALVE ASM, SMALL, PE EPDM PAC

23 2 26, 27-4AV, 28-5BV 1340-03 VALVE ASM, SMALL PE VITON PAC

23 2 28-6BE 1340-92 VALVE ASM SMALL, HALAR, EPDM

23 2 28-6BE 1340-93 VALVE ASM SMALL, HALAR VITON

24 2 27-1AE 1341-02 VALVE ASM LARGE, PE EPDM, PAC

24 2 26, 27-4AV, 28-5BV 1341-03 VALVE ASM, LARGE PE VITON, PAC

24 2 28-6BE 1341-92 VALVE ASM LARGE, HALAR EPDM

24 2 28-6BE 1341-93 VALVE ASM LARGE, HALAR VITON

26 1 ALL PUMP MODELS 1038-10 SCREEN, FILTER, SS, PAC

28 1 27-1AE 1338-02 PISTON ASM, PE, EPDM, PAC

28 1 26, 27-4AV, 28-5BV 1338-03 PISTON ASM, PE, VITON, PAC

28 1 28-6BE 1338-92 PISTON ASM, HALAR, EPDM, PAC

28 1 28-6BE 1338-93 PISTON ASM, HALAR, VITON, PAC

29 1 27-1AE, 28-6BE 1029-72 O-RING, PISTON, EPDM, PAC

29 1 26, 27-4AV, 28-5BV 1029-73 O-RING, PISTON, VITON, PAC

30 1 26, 27-1AE, 27-4AV 1028-90 RING, PISTON, TEFLON, PAC

30 1 28-5BV, 28-6BE 2024-90 RING, PISTON, TEFLON, THICKER

31 1 ALL PUMP MODELS 1056-10 CLAMP, BUNG ADAPTER, SS, PAC

32 1 26, 27-1AE, 27-4AV 1043-01 ADAPTER, PE, CORK NITRILE, PAC

32 1 28-6BE 1201-92 ADAPTER, HALAR W/ EPDM, PAC

32 1 27-4AV, 28-5BV, 28-6BE 1201-93 ADAPTER, HALAR W/ VITON, PAC

33 1 26, 27-1AE, 27-4AV 1381-90 GASKET, BUNG ADAPTER, PAC

33 1 28-6BE 1822-72 O-RING, BUNG ADAPTER, EPDM PAC

33 1 28-6BE 1822-73 O-RING, BUNG ADAPTER VITON PAC

34 1 26, 27-1AE, 27-4AV 1007-30 TUBE, EXTENSION, 16-1/2 PE PAC

34 1 28-5BV, 28-6BE 1007-90 TUBE, EXTENSION, 16-1/2 TEFLON

35 1 26, 27-1AE, 27-4AV 1055-30 COUPLING, 1” NPT PE, PAC

35 1 28-5BV, 28-6BE 1055-90 COUPLING, 1” NPT HALAR, PAC

36 1 26, 27-1AE, 27-4AV 1045-30 TUBE, SUCTION, 16-1/2 PE, PAC

36 1 26, 27-1AE, 27-4AV 2029-30 TUBE, SUCTION, 10-1/4” PE, PAC

36 1 28-5BV, 28-6BE 1045-90 TUBE, SUCTION, 16-1/2 TEFLON

37 1 26, 27-1AE, 27-4AV 1022-30 HOUSING, PUMP, HALAR, PAC

37 1 28-5BV, 28-6BE 1022-60 HOUSING, PUMP, RYTON, PAC

38 1 26, 27-1AE, 27-4AV 2022-30 PLUG, VENT, PE, PAC

38 1 28-5BV, 28-6BE 2022-90 PLUG, VENT, HALAR, PAC

Questo manuale è adatto per i seguenti modelli

Altri manuali morse Pompa dell'acqua

morse

morse 96MK1939-P Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente

morse 26 Manuale utente

Manuali Pompa dell'acqua popolari di altre marche