Motorola MC4000 Manuale utente
Quick Start
Guide
cellular multisensor
Model MC4000
2
Let's get started
The Motorola Cellular MultiSensor senses temperature,
humidity, water/flood, light intensity, shaking/acceleration,
presence of AC power, cell signal strength, and backup
battery status. Please see Sensor Details on page 14 for
specifics about these sensors.
Installing the MultiSensor
The Motorola Cellular MultiSensor is easy to install. Here's
what to do:
1Switch on the MultiSensor's backup battery.
The battery's switch is shown below. Use a paper clip, pen,
or similar pointed object to gently move the slider to the 1
position (Battery ON).
Keep the switch in the ON position unless you're not
going to be using the MultiSensor for a long period of time
and you want to save battery power. Note that the
battery will only charge when the switch is in the ON
position.
2Plug the MultiSensor into a power source.
Typically, you plug the MultiSensor into the included USB
power cube, and then plug the USB power cube into an
3
AC wall outlet that's powered on. If you plan to use the
MultiSensor's water-sensing probe, you'll want to plug the
sensor and cube into a power outlet near the source of a
possible "flood". If you're not using the probe, think about
which sensors you want to use and place the MultiSensor
accordingly.
Here are some other possible sources of power:
a. A computer's USB port. To ensure consistent power
supply, the computer should be configured to be
running all the time. (Note: the heat generated from
the computer may affect the MultiSensor's
temperature and humidity readings.)
b. A suitable USB power bank. A USB power bank is
useful if you want to run the MultiSensor for more
than 2 days without AC power. Care should be
taken in selecting a compatible power bank as many
power banks have auto-shut off features that
cannot be disabled. For compatible power bank
suggestions, please see
www.motorolanetwork.com/PowerBanks
4
3If you want to monitor for "flood", plug in the water-
sensing probe.
Plug the included water-sensing probe into the micro-USB
port on the MultiSensor as shown. You can put the probe
on the floor, or you can mount it on a wall or post if you
prefer.
The water sensing probe works when the metal probes
both make contact with water. When the water sensor is
on a floor, the metal probes should rest on the floor.
The flood cable length is 5 feet. If you need a longer cable,
you can plug the flood cable into a Micro-USB Extension
Cable, which has a micro-USB male connector on one end
and micro-USB female connector on the other end. These
are inexpensive, and various lengths are available online.
5
Setting up service using the
MultiSensor app or a Web browser
Now that you have the hardware installed, you can connect
and configure your device using the web browser or the
Motorola MultiSensor app on an iPhone or one of the many
popular Android phones made by Motorola, Samsung, and
many other companies.
Instructions below are for installation using the app for
smartphones, iPads, and other smart devices. If you are going
to use the web browser instead, go to:
https://sensor.motorolanetwork.com/, and substitute clicks
for taps in the instructions below.
If you are adding a MultiSensor to an existing account, skip to
step 3.
1Download the Motorola MultiSensor app for Android or
iPhone through Google Play or the Apple App Store.
Search for Motorola MultiSensor and look for the
Motorola icon below. Follow the instructions on your
smart device to download and install the app. (Or, go to
https://sensor.motorolanetwork.com/in your web
browser.)
2Set up your account.Once it is installed, the app will
appear on your device with the name MultiSensor.
Opening the mobile app, a Sensor App Login Page is
displayed.
6
•On the bottom right of the page
is a
Sign Up
selection. Select it
then complete the information
requested on the next page.
This information (e-mail and
phone number) will be used as
the default Alert Recipient for
this account but may be edited
later.
•A registration code will be sent
to the e-mail address provided.
This code will need to be
entered to finish setting up the
account.
Note: once the account is set up you will need to login
using the provided e-mail address and password to
continue with further setup.
3Add your MultiSensor. Tap the Configuration tab at the
bottom of the screen. Tap Sensor and then the blue +to
add your sensor. You will see a page with fields to be
complete.
•Sensor Name – use
Upper/Lower case letters and
numbers only. No special
characters. For example,
Basement or Beach House.
•
Sensor ID (IMEI Number)
–
type the unique IMEI number
that’s printed on a label on your
MultiSensor. You may wish to
write this down or take a picture
of it.
7
•
Upload button
– you can
optionally upload a photo to
help identify your MultiSensor,
and the photo will be displayed
on the Dashboard page. If
Upload is not selected, then a
sensor picture will be used.
Note: This default picture is not
displayed on this page but will
appear on the Dashboard once
the sensor is added.
•
Time Zone
– a selection box to
select the time zone where the
sensor is used.
Once all fields are complete, the ADD button at the
bottom will become selectable to finish adding the sensor
to this account.
Note: If using the browser URL and not the mobile app,
then Configure is at the top of the page. When selected,
the next page on the left will display Add a New Sensor
with the same fields. The default picture is displayed. At
the bottom of the page, click Save.
4Finally, you will need to set up and activate a
subscription for service for your MultiSensor. The first
month of service is free. Subsequent months are $5 per
month per sensor. When you add an additional
MultiSensor to an existing account, the service begins
charging on the next billing cycle after it is installed.
8
•Select
Account
. Select
My
Wallet
and follow the
prompts on the
Manage
Wallet
page to
Add a new
payment method
and to
enter billing information.
Then tap
Add your Card
.
The page
Select a billing
address
will display. If the
address is already populated,
select it and select
Use this
Address
. Otherwise, tap
Add
a new Address
. Complete
the fields and select
Add
.
•Once the payment
information is setup, return
to the Account page and
select
Payments
which
displays the
Payments
page.
Tap
Activate
for the desired
sensor displayed and follow
the prompts on the
Billing
Plan
page to set up your
subscription. After selecting
Place Your Order
, a Receipt
screen will display, and an
email will be sent to the
Account Holder confirming
your subscription. Your
subscription should be
activated!
9
Using your MultiSensor
Reading the MultiSensor Dashboard. The Dashboard
displays information reported by all the sensors, and signal,
power and battery status. The Updated field tells you the last
report time. Normally the device reports every 20 minutes. If
you tap the device icon at the top of the dashboard, the
dashboard will show you data from the most recent report. If
you tap the Refresh button, the device will send a fresh report
with up-to-the-minute data. If after installation you see a
grayed-out dashboard, unplug your sensor, switch the battery
off, and turn it back on. Then plug the sensor back in.
Configure your MultiSensor for the way you want to use it.
Tap the Dashboard tab at the bottom of the screen on your
mobile app (the browser on your computer displays
Dashboard on the top left). After a short delay, you should see
the Dashboard screen with information displayed from your
MultiSensor.
•Tap any Dashboard sensor icon
to enable and configure alerts,
and to view history. If you'd
like, you can set alerts for any
sensor. For instance, you may
want to be alerted if there's
water on your floor or if the
temperature drops below 47
degrees, or if there's a power
loss.
Follow the on-screen
instructions for details and
read the next section for
additional assistance.
Indice
Altri manuali Motorola Accessori
Motorola
Motorola Horizonmacro outdoor Manuale utente
Motorola
Motorola ASTRO 25 GTR 8000 Guida utente
Motorola
Motorola AirDefense Model 510 Manuale utente
Motorola
Motorola hmsm4050 Manuale utente
Motorola
Motorola hmsm4050 Manuale utente
Motorola
Motorola ENLN4103 Manuale utente
Motorola
Motorola RDU4160d Manuale utente
Motorola
Motorola MTR2000 T5544 Manuale utente
Motorola
Motorola Focus TAG Manuale utente
Motorola
Motorola LM100 - SOUTHERNLINC Manuale utente
Motorola
Motorola MTS LiTE Manuale utente
Motorola
Motorola MTR2000 Manuale utente
Motorola
Motorola sd4581 Manuale del proprietario
Motorola
Motorola 8900 - Blackberry Curve Cell Phone OEM Car... Manuale di istruzioni
Motorola
Motorola C370 Series Manuale utente
Motorola
Motorola sd4561 Manuale del proprietario
Motorola
Motorola Motoactv Manuale utente
Motorola
Motorola P1500 Manuale utente
