Motorola DCT5100 Manuale utente
DCT5100
User Guide
INFO
MENU
POWER
A/B
GUIDE SMARTCARD
SELECT
C
H
A
N
N
E
L
C
U
R
S
O
R
MSGS.
ON REMOTE
A/B
L AUDIO IN RUSB VIDEOIN
CAUTION
RISK OF ELECTRIC SHOCK
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
CAUTION:
Graphical symbols and supplemental warning marking locations on bottom of terminal.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION
TO PREVENT ELECTRICAL SHOCK, DO NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS
THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point, within an equilateral triangle, is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
This installation should be made by a qualified service person and should conform to all
local codes.
REPAIRS
If you find the unit in need of repair, contact your cable system operator for repair or
replacement.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building, as close as
possible to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING
Antenna lead
in wire
Ground
clamp
Antenna
discharge unit
(NEC Section 810-20)
Grounding conductors
(NEC Section 810-21)
Grounding
clamps
Power service grounding
electrode system
(NECArticle250,PartH)
Electric service
equipment
NEC=NATIONAL ELECTRICAL CODE
Copyright © 2002 by Motorola, Inc. All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without written permission
of the publisher.
Dolby Digital is manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Copyright © 2002 Dolby Laboratories. All
rights reserved.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners.
© Motorola, Inc. 2002.
Important Safety Instructions
1Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
2Retain instructions
The safety and operating instructions should be
retained for future reference.
3Heed warnings
All warnings on the appliance and in the
operating instructions should be adhered to.
4Follow instructions
All operating and use instructions should be
followed.
5Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6Attachments
Do not use attachments not recommended
as they may cause hazard.
7Water and moisture
Do not use this equipment near water; for
example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near
a swimming pool, and the like.
8Accessories
Do not place this product on an unstable stand,
cart, tripod, bracket, or table. The product may fall
causing serious injury and damage to the appliance.
Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer or sold
with the equipment. Follow the manufacturer’s
instructions when mounting the appliance, and use
a mounting accessory recommended by the
manufacturer.
9Ventilation
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
equipment. The openings should never be blocked
by placing the product on a bed, sofa, rug, or
similar surface. The unit should be positioned with
at least 2 inches of space above and on all sides.
No items should be placed on top of the unit.
Equipment should never be placed near or over a
radiator or heat register, onto heat dissipating
equipment, or in a built-in installation such as a
bookcase unless proper ventilation is provided.
The unit has been designed to operate reliably in a
well-ventilated household environment.
10 Power sources
This product should be operated only from the
power sources indicated on the marking label. If
you are unsure of the type of power supplied to
your home, consult your local power company.
For equipment operating from battery power or
other sources, refer to the operating instructions.
11 Ground or polarization
This equipment may be equipped with a polarized
alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12 Alternate warnings
This equipment may be equipped with a 3-wire
grounding-type plug, a plug having a third
(grounding) pin. This pin will only fit into a
grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into
the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
13 Power cord protection
Power supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the appliance.
14 Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the equipment, be sure the antenna or cable
system is grounded as to provide some protection
against voltage surges and built-up static charges.
15 Lightning
For added protection for this equipment during
a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna
or cable system. This will prevent damage to
the video product due to lightning and power
line surges.
16 Power lines
An outside antenna system should not be
located in the vicinity of overhead power lines
or where it can fall into such power lines or
circuits. When installing an outside antenna
system, extreme care should be taken to keep
from touching such power lines or circuits as
contact with them may be fatal.
17 Overloading
Do not overload wall outlets and extension
cords as this can result in a risk of fire or
electrical shock.
18 Object and liquid entry
Never push objects of any kind into this
equipment through openings as they may touch
dangerous voltage points or short-out parts that
could result in a fire or electrical shock. Never
spill liquid of any kind on the product.
19 Servicing
Do not attempt to service this equipment
yourself as opening or removing covers may
expose you to dangerous voltage or other
hazards, refer all servicing to qualified
service personnel.
20 Damage requiring service
Unplug this equipment from the wall outlet and
refer servicing to qualified service personnel under
the following conditions:
aWhen the power supply cord or plug is
damaged.
bIf the equipment has been exposed to rain
or water.
cIf liquid has been spilled, or objects have fallen
into the equipment.
dIf the equipment does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the
equipment to its normal operation.
eIf the equipment has been dropped or cabinet
has been damaged.
fWhen the equipment exhibits a distinct change
in performance, indicating a need for service.
21 Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
22 Safety check
Upon completion of any service or repairs to this
video product, ask the service technician to
perform safety checks to determine that the
product is in proper operational condition.
23 Telephone equipment
Observe the following precautions when installing
telephone modem equipment:
aNever install telephone wiring during a
lightning storm.
bNever install telephone jacks in a wet
location unless the jack is specifically designed
for wet locations.
cNever touch uninsulated telephone wires or
terminals unless the telephone lines have been
disconnected at the network interface.
dUse caution when installing or modifying
telephone lines.
24 Battery usage
Notwithstanding any information provided by
Motorola in this manual regarding the use of
batteries, the end user assumes all responsibility
and liability to use and dispose of batteries in
accordance with all applicable laws, rules and
regulations. Motorola will not be liable to anyone
for the end user's failure to use and/or dispose of
batteries in the proper manner and in accordance
with such laws, rules and regulations, or for any
defect contained in batteries which may cause
injury damage to persons or property.
REGULATORY INFORMATION
Federal Communications Commission Radio and Television Interface Statement for a
Class ‘B’ Device.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in the residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If the equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•Increase the separation between the equipment and the effected receiver
•Connect the equipment on a circuit different from the one the receiver is on
You may find the following booklet, prepared by the Federal Communication Commission,
helpful:
How to Identify and Resolve Radio-TV Interference Problems
Stock No. 004-000-0342-4,
U.S. Government Printing Office
Washington, DC 20402
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Canadian Compliance
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B
respects toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Declaration of Conformity
According to 47CFR, Parts 2 and 15 for Class B Personal Computers and Peripherals;
and/or CPU Boards and Power Supplies used with Class B Personal Computers, Motorola
BCS, 6450 Sequence Drive, San Diego, CA 92121, 1-800-225-9446, declares under sole
responsibility that the product identifies with 47CFR Part 2 and 15 of the FCC Rules as a
Class B digital device. Each product marketed is identical to the representative unit tested
and founded to be compliant with the standards. Records maintained continue to reflect the
equipment being produced can be expected to be within the variation accepted, due to
quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation
is subject to the following condition: This device must accept any interference received,
including interference that may cause undesired operation. The above named party is
responsible for ensuring that the equipment complies with the standards of 47CFR,
Paragraph 15.101 to 15.109. The Class B digital apparatus meets all requirements of the
Canadian Interface Causing Equipment Regulations.
FCC Part 68 Statement
This equipment complies with part 68 of the FCC rules. On the rear panel of this equipment is a
label that contains, among other information, the FCC registration number and ringer equivalence
number (REN) for the equipment. If requested, this information must be provided to the telephone
company.
The REN is used to determine the quantity of devices that may be connected to the telephone line.
Excessive RENs on the telephone line may result in the devices not ringing in response to an
incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to the line, as determined by the total
RENs, contact the telephone company to determine the maximum REN for the calling area.
This equipment uses the following USOC jack: RJC. An FCC-compliant telephone cord and
modular plug is provided with this equipment. This equipment is designed to be connected to the
telephone network or premises wiring using a compatible modular jack that is Part 68 compliant.
This equipment cannot be used on telephone company-provided coin services. Connection to
Party Line Service is subject to state tariffs.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that the temporary discontinuance of services may be required. If advance notice isn’t
practical, the telephone company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures
that could affect the operation of the equipment. If this happens, the telephone company will
provide advance notice in order to maintain uninterrupted service.
If the trouble is causing harm to the telephone system, the telephone company may request that
you remove the equipment from the network until the problem is resolved.
Industry Canada CS-03 Statement
The Industry Canada label identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment Technical Requirements
document(s). The department does not guarantee that the equipment will operate to the
user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer should be aware that
compliance with the above conditions might not prevent degradation of service in some
situations. Only a representative designated by the supplier should coordinate repairs to
certified equipment. Repairs or alterations made by the user to this equipment, or
equipment malfunctions may give the telecommunication company cause to request the
user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas. Users
should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
The Ringer Equivalence Number (REN) of this device is displayed on the product. The REN
assigned to each terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termination on an interface
may consist of any combination of devices subject only to the requirement that the sum of
the Ringer Equivalence Numbers of all devices does not exceed 5. The telephone
connection arrangement is a CA11A.
CONTENTS
Introduction................................................. 2
Front Panel.........................................................................3
Rear Panel...........................................................................6
Remote Control............................................9
Installing Batteries...........................................................13
Basic Operation.......................................... 14
Turning Power On and Off..........................................14
Changing Channels.........................................................14
Adjusting the Volume....................................................14
Audio/Video Connections...........................15
RF Bypass Switch............................................................16
High Definition Television ......................... 19
On-Screen Display.........................................................19
User Options...................................................................20
Video Connections........................................................ 26
Data Features .............................................27
Data Device Connection ............................. 28
Recording Your Connections.....................29
Troubleshooting.........................................30
2
INTRODUCTION
Congratulations on receiving the Motorola DCT5100, the most advanced
interactive digital consumer terminal available today. The powerful
processing capability of the DCT5100 and integrated cable modem bring the
world of high-speed data, internet access, and advanced interactive
applications to your television-viewing environment.
With the appropriate applications and network support, the DCT5100 is
capable of much more than just delivering hundreds of analog and digital
video channels. The DCT5100 can provide exciting services such as
high-definition video, electronic program guides, high-speed data, internet
access, e-mail, Video-On-Demand, video conferencing, IP telephony,
E-Commerce, home banking, and much more. The DCT5100 can interface
to an external data device, such as a PC, using several high-speed
interfaces -Ethernet, USB, or optional IEEE 1394 “Firewire.” These
interfaces enable a PC to share the integrated cable modem resources, as
well as pass data and video to an external device for further processing.
This User Guide introduces you to the basic features of the DCT5100 and
provides several options for integrating it into your current entertainment
system. The advanced features of the DCT5100, such as the cable modem,
are dependent on the applications and network infrastructure supported by
your system. Check with your service provider to determine which features
are being offered in your area. They also provide instructions for the
optional services.
3
INTRODUCTION
Front Panel
The DCT5100 front panel has 12 keys, an LED display, a Universal Serial
Bus (USB) connector, and connectors for audio and video. Use the keys to
perform basic functions such as access the electronic program guide, navigate
menus, and purchase pay-per-view events.
The table following this drawing describes each connection and its use. For
more information on the front panel, see the Remote Control section.
INFO A/B
MENU
GUIDE
POWER
SELECT
C
H
A
N
N
E
L
C
U
R
S
O
R
SMART CARD
P
MUTE
MSGS.
ON REMOTE
A/B
USB VIDEO IN L AUDIO IN R
1
2
3
4
5
6
7
8
9
10
11
12
13
4
INTRODUCTION
Key Description
1USB The Universal Serial Bus (USB) connector is used to support devices such as keyboards, joysticks, scanners,
disk storage, PCs, printers, and digital cameras.
2VIDEO IN The VIDEO IN connector accepts a baseband video input from a VCR, camcorder, or other video device.
3AUDIO IN R
AUDIO IN L
These connectors are used for connecting the set-top between a CD player and a stereo tuner (or other audio
peripheral). Audio from the auxiliary device will pass through the DCT5100 when it is turned off.
4LED Displays the channel number or time of day.
There are four indicator lights on the LED screen:
•MSGS. —the DCT5100 has received messages for you to read
•ON —the DCT5100 is powered on
•A/B —the RF bypass is active
•REMOTE —the remote control is in use
5SMART
CARD SLOT This interface is intended to support electronic commerce activity utilizing a smart card. Contact your service
provider for availability.
6CURSOR Moves the cursor around the program guide and menu screens.
7MENU Displays the main menu.
Altri manuali per DCT5100
10
Indice
Altri manuali Motorola Ricevitore TV
Motorola
Motorola DCX3200 Manuale utente
Motorola
Motorola DCH200 Manuale utente
Motorola
Motorola at&t U-verse VIP2500 Series Manuale utente
Motorola
Motorola Fibe Internet Manuale utente
Motorola
Motorola DCH3416 Manuale utente
Motorola
Motorola VIP1200 Series Manuale utente
Motorola
Motorola QIP7100 Series Manuale utente
Motorola
Motorola VT71 Manuale utente
Motorola
Motorola DCT 5100 HD Manuale utente
Motorola
Motorola VIP2502W Manuale utente
