Moxa Technologies UC-8100 Series Manuale utente

P/N: 1802081000014

*1802081000014*

UC-8100 Series

Quick Installation Guide

Version 4.1, January 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The UC-8100 computing platform is designed for embedded

data-acquisition applications. The computer comes with one or two

RS-232/422/485 serial ports and dual 10/100 Mbps Ethernet LAN ports,

as well as a Mini PCIe socket to support cellular modules. These versatile

communication capabilities let users efficiently adapt the UC-8100 to a

variety of complex communication solutions.

Package Checklist

•UC-8100 embedded computer

•Console cable

•Power jack

•3-pin terminal block for power (preinstalled)

•5-pin terminal block for UART x 2 (preinstalled)

Please notify your sales representative if any of the above items are

missing or damaged.

Panel Layout

The following figures show the panel layouts of the UC-8100.

Top and Bottom Panel

Top

Bottom

- 3 -

Front Panel

LED Indicators

LED Name

Color

Function

USB

Green

Steady On

USB device is connected

and working normally

Off

USB device is not

connected.

SD Green Steady On SD Card inserted and

working normally

Off

SD card is not detected

Power

Green

Power is on and the computer is

working normally.

Off

Power is off.

LAN1/2

(On RJ45

connector)

Green

Steady On

100 Mbps Ethernet link

Blinking

Data transmitting

Yellow

Steady On

10 Mbps Ethernet link

Blinking

Data transmitting

Off

Ethernet is not connected

Wireless

Signal

Strength

Green

Yellow

Red

Number of glowing LEDs indicates

signal strength

3 (Green + Yellow + Red): Excellent

2 (Yellow + Red): Good

1 (Red): Poor

Off

Wireless module is not detected

Diagnosis

Green

Yellow

Red

These 3 LEDs are used for diagnostics

and are programmable. For additional

details, refer to the UC-8100 Series

Hardware Manual.

- 4 -

Installing the UC-8100

There are two sliders on the back of the unit for DIN-rail and wall

mounting.

Mounting on a DIN Rail

Pull out the bottom slider, latch the unit onto the DIN rail, and push the

slider back in.

Mounting on a Wall

Pull out both the top and bottom

sliders,

align the screws with the

mounting holes, and secure the

dev

ice to the wall by driving the

screws into the wall

Another method for wall mounting installation is to use the optional wall

mounting kit. Attach two mounting brackets on the side panel of the

computer, and fasten with screws. Install the computer on to a wall or

cabinet by fastening two screws for each mounting bracket.

Connector Description

Power Connector

Connect the “terminal block to power jack converter” (included in the

package) to the UC-8100’s DC terminal block (located on the top panel),

and then connect the power adapter. It takes about 30 seconds for the

system to boot up. Once the system is ready, the Power LED will light up.

- 5 -

Grounding the UC-8100

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI).

SG:

The s

hielded

ground (sometimes called

rotected ground) contact is the top

contact of the 3

-pin power terminal

block connector when viewed from the

angle shown here. Connect the SG wire

to an appropriate grounded metal

surface.

ATTENTION

The product is intended to be supplied by an UL Listed power

adapter whose output meets SELV/LPS, and is rated 12

24 VDC,

minimum 0.5 A, Tma = 85°C (minimum).

Ethernet Ports

The two 10/100 Mbps Ethernet ports (LAN 1 and LAN 2) use RJ45

connectors. Refer to the following table for the pin assignments.

Signal

ETx+

ETx-

ERx+

ERx-

Serial Ports

The two serial ports (P1 and P2) use terminal connectors. Each port can

be configured by software for RS-232, RS-422, or RS-485. Refer to the

following table for the pin assignments.

RS-232

RS-422

RS-485

TXD

TXD+

–

RXD

TXD-

–

RTS

RXD+

D+

CTS

RXD-

D-

GND

SD/SIM Card Slots

The UC-8100 comes with an SD slot for storage expansion and a SIM card

slot for cellular communication. The SD card/SIM card slots are located at

the lower part of the front panel. To install them, remove the screw and

the cover to access the slots, and then insert the SD card or the SIM card.

You will hear a click when they are inserted correctly. To remove them,

push the cards in and then release them.

- 6 -

Console Port

The console port is a RS-232 port that can be connected with a 4-pin pin

header cable. You may use this port for debugging or firmware upgrade.

Signal

TxD

RxD

GND

USB

The USB 2.0 port is located at the lower part of the front panel, and

supports a USB storage device driver.

Real-time Clock

The UC-8100’s real-time clock is powered by a non-chargeable battery.

We strongly recommend that you do not replace the battery without help

from a qualified Moxa support engineer. If you need to change the battery,

contact the Moxa RMA service team.

ATTENTION

There is

a risk of explosion if the battery is replaced by an

incorrect type of battery.

Installing the Cellular Module

The UC-8100 provides a Mini PCIe socket for installing a cellular module.

The cellular module package includes the following items.

- 7 -

Follow these steps to install the cellular module.

Unfasten the screws on the side

panel of the computer and

remove the cover.

2. Find the location of the PCIe

socket.

3. Remove the plastic plate and the

sticker on both sides of the

large thermal pad and place it

in the socket

. Press the thermal

pad down s

o that it sticks to the

base of the socket.

Place the thermal pad as close

as possible to the holes for the

screws used to secure the

module.

4. Insert the cellular module into

the socket and tighten the

screws to secure the module to

the socket.

- 8 -

5. Remove the plastic plate and the

sticker on both side of the

small

thermal pad and stick the

thermal pad on to the module.

Install the antenna cables.

There are three antenna

connectors

on the module; two

for cellular antennas and one for

a GPS antenna. Refer to the

figure for details. As there are

only two antenna connector

holes on the front panel of the

computer, you can only use two

antennas at a time. You may use

two cellular antennas, or a

cellular antenna and a GPS

antenna. The same antenna

cables can be used for both

antenna types.

7. Connect one end of the antenna

cable to the cellular module.

8. Insert the other end of the

cable, with the connector,

through the antenna

connector

hole on the front panel of the

computer. Remove the black

plastic protection cover on the

connector hole before you insert

the antenna wire.

9. Insert the locking washer

through the connector and press

it against the cover of the

computer. Then, insert the nut

and tighten it to secure the

connector to the cover.

- 9 -

10. Connect the antenna to the

antenna connector.

11.

Replace the cover of the

computer.

Connecting the UC-8100 to a PC

A. Through the serial console port with the following settings:

Baudrate=115200 bps, Parity=None, Data bits=8, Stop bits

=1, Flow Control=None

ATTENTION

Remember to choose the “VT100” terminal type. Use the

CBL

-RJ45F9-150 cable included in the package to connect the

to the UC-8100’s serial console port.

B. By SSH over the network. Refer to the following IP addresses and

Default IP Address

Netmask

LAN 1

192.168.3.127

255.255.255.0

LAN 2

192.168.4.127

255.255.255.0

Password: moxa

Altri manuali per UC-8100 Series

Indice

Altri manuali Moxa Technologies Hardware per computer

Moxa Technologies

Moxa Technologies Industio CP-114 Series CP-114 Series Manuale utente

Moxa Technologies

Moxa Technologies CCG-1500 Series Manuale utente

Moxa Technologies

Moxa Technologies CP-118EL Manuale utente

Moxa Technologies

Moxa Technologies MiiNePort E1-SDK Manuale utente

Moxa Technologies

Moxa Technologies CA-132/132I Manuale utente

Moxa Technologies

Moxa Technologies Industio C114HI Manuale utente

Moxa Technologies

Moxa Technologies CP-118U Series Manuale utente

Moxa Technologies

Moxa Technologies CP-118U Series Manuale utente

Moxa Technologies

Moxa Technologies MPC-2101 Series Manuale utente

Moxa Technologies

Moxa Technologies Moxa Smartio C168H Manuale utente

Moxa Technologies

Moxa Technologies Smartio CP-168U Manuale utente

Moxa Technologies

Moxa Technologies WAPN008-1 Manuale utente

Moxa Technologies

Moxa Technologies C104P Manuale utente

Moxa Technologies

Moxa Technologies WAPN008 Manuale utente

Moxa Technologies

Moxa Technologies CP-102U/UL Manuale utente

Moxa Technologies

Moxa Technologies THINKCORE W311 Manuale utente

Moxa Technologies

Moxa Technologies Industio C114HI Manuale utente

Moxa Technologies

Moxa Technologies ABC-02-USB-T Manuale utente

Moxa Technologies

Moxa Technologies EM-1220 LX Manuale utente

Moxa Technologies

Moxa Technologies Smartio C104H Manuale utente

Moxa Technologies

Moxa Technologies DA-661 Istruzioni per l’uso

Moxa Technologies

Moxa Technologies MAR-2000 Istruzioni per l’uso

Moxa Technologies

Moxa Technologies DA-661 Manuale utente

Moxa Technologies

Moxa Technologies VPort 66-2MP Series Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente