Moxa Technologies OnCell Series Manuale utente

P/N: 1802034700011

*1802034700011*

OnCell G3470A-LTE

Quick Installation Guide

Moxa OnCell Series

Version 2.1, December 2020

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The OnCell G3470A-LTE is Moxa's 4G/Ethernet IP gateway that provides a

higher cellular bandwidth and more reliable connection to your Ethernet

network for cellular applications. With the integrated 4-port gigabit

Ethernet switch and 4G LTE support, the OnCell G3470A-LTE offers a

faster cellular connection with a lower total cost of ownership. To enhance

reliability, a key for industrial users, the OnCell G3470A-LTE features

isolation design for both power and antenna inputs. Coupled with

high-level EMS and wide-temperature support, the OnCell G3470A-LTE

provides the highest level of device stability in any rugged environment.

In addition, with dual SIM and dual power-input features, the OnCell

G3470A-LTE supports network redundancy to ensure an uninterrupted

connectivity in your applications.

Package Checklist

Moxa’s OnCell G3470A-LTE is shipped with the following items. If any of

these items is missing or damaged, please contact your customer service

representative for assistance.

•OnCell G3470A-LTE

•1 GPS connector terminator

•2 2G/3G/4G omni-directional antennas, 2 dBi, SMA (male)

•5 plastic RJ45 protective caps for serial console and Ethernet ports

•Quick installation guide (printed)

•Warranty card

Installation and Configuration

Before installing the OnCell G3470A-LTE, make sure that all items in the

package checklist are in the box. In addition, you will need access to a

notebook computer or PC equipped with an Ethernet port. The OnCell

G3470A-LTE has a default IP address that you must use when connecting

to the device for the first time.

Step 1: Insert a SIM card and turn on the OnCell G3470A-LTE

Insert one or two 2G/3G/4G SIM cards into the SIM slots located on the

bottom of the OnCell G3470A-LTE. Then, turn on the OnCell G3470A-LTE

by connecting a power terminal block to a DC power source (12 to 48

VDC).

Step 2: Connect the OnCell G3470A-LTE to a notebook or PC

Since the OnCell G3470A-LTE supports MDI/MDI-X auto-sensing, you can

use either a straight-through cable or crossover cable to connect the

OnCell G3470A-LTE to a computer. If the LED indicator on the OnCell

G3470A-LTE’s LAN port lights up, it means a connection has been

established.

Step 3: Set up the computer’s IP address

Set an IP address on the same subnet as the OnCell G3470A-LTE. Since

the OnCell G3470A-LTE’s default IP address is 192.168.127.254, and the

subnet mask is 255.255.255.0, you should set the IP address of the

computer to 192.168.127.xxx and subnet mask to 255.255.255.0.

- 3 -

Step 4: Use the web-based manager to configure the OnCell

G3470A-LTE

Open your computer’s web browser and type http://192.168.127.254

in the address field to access the homepage of the web-based

management system. Before the homepage opens, you will need to enter

the user name and password. For first-time configuration, enter the

default user name and password and then click on the Login button:

User name: admin

Password: moxa

ATTENTION

For security reasons, we strongly recommend changing the

password. To do so, select

Maintenance



Usern

ame/Password, and then follow the on-screen

instructions.

NOTE

For the change to take effect, you must click Save Configuration

to save the change, or Restart (clicking the Save and Restart

buttons will save all changes).

- 4 -

Hardware Overview

1. GPS antenna connector (fe

male

SMA)

Terminal block (two digital input

and one digital relay)

3. Grounding screw (M5)

4. Terminal block (PWR1 and

PWR2)

2x2 MIMO antenna ports for LTE

(female SMA)

6. RS-232 serial console (RJ45)

7. 10/100/1000

BaseT(X) Ethernet

ports (RJ45)

8. LED display

9. DIN-rail mounting kit

10.

Reset button

11.

Dual SIM – SIM1

12.

Dual SIM – SIM2

- 5 -

Device Dimensions

DIN-Rail Mounting

DIN-Rail Kit Dimensions:

Unit = mm (inch)

The DIN-rail kit is attached to the back panel of the OnCell G3470A-LTE

series. Mount the OnCell G3470A-LTE series on corrosion-free mounting

rails that meet the EN 60715 standard.

- 6 -

Installation

STEP 1: Insert the upper lip of

the DIN rail into the DIN

-rail

mounting kit.

STEP 2:

Press the OnCell

G3470A

LTE series towards the

DIN rail until it snaps into place.

Removal

STEP 1: Pull down the latch on

the mounting kit using a

screwdriver.

STEP 2: Slightly pull the OnCell

G3470A

-LTE forward.

STEP 3

: Lift up to remove the

OnCell G3470A

-LTE from the

DIN rail

Wall Mounting (optional)

Wall-mount Kit Dimensions:

Unit = mm (inch)

- 7 -

For some applications, it may be more convenient to mount the OnCell

G3470A-LTE to a wall, as illustrated below.

STEP 1:

Remove the aluminum

DIN

-r

ail attachment plate

from the

OnCell

G3470A

-LTE, and then

attach

the wall mount

plates with M3 screws, as

shown in the adjacent

diagram.

STEP 2:

Mounting the

OnCell G3470A-LTE

to a wall requires 4

screws. Use the

OnCell G3470A-LTE

device, with wall

mount plates attached as a guide

to mark the correct

locations of th

e 4 screws. The heads of the screws

should be less than 6.0 mm in diameter, and the

shafts

should be less than 3.5 mm in diameter, as shown in

the figure at the right.

NOTE

Test the screw head and shank size by inserting the screw into

one of the keyhole shaped apertures of the Wall Mounting Plates

before it is screwed into the wall.

STEP 3:

Once the screws are fixed into the

wall, insert the four screw heads

through the large opening of the

keyhole

-shaped apertures, and

then slide the

OnCell G3470A-LTE

downwards, as indicated

in the

accompanying diagram.

Tighten

the four screws for added stability.

WARNING

•

This equipment is intended to be used in a Restricted Access

Location, such as a dedicated computer room. Access can

only be gained by SERVICE PERSONS or by USERS who have

been instructed about the fact that the metal chassis of the

equipment is extremely hot and may cause burns.

•

Service persons or users should pay special attention and

take special precautions before handling the equipment.

•

Access should be controlled with lock and key,

or a security

identity system controlled by the authority responsible for

the location. Only authorized, well-trained professionals

should be allowed to access the restricted access location.

•

External metal parts are hot!! Pay special attention or use

special protection before handling.

- 8 -

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa OnCell G3470A-LTE.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical cod

es dictating the

maximum current allowed for each wire size.

If the current goes

above the maximum ratings, the wiring could overheat, causing

serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked “Class 2” or “LPS” and rated O/P: 9.6 W (12 V/0.78 A to

48 V/0.2 A).

ATTENTION

Make sure

that the external power adapter

(includes power cords

and plug assemblies) provided with the unit is certified and

suitable for use in your country.

- 9 -

Grounding the Moxa OnCell G3470A-LTE

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

Wiring the Redundant Power Inputs

The top two pairs of contacts of the 10-contact terminal block connector

on the OnCell G3470A-LTE’s top panel are used for the OnCell

G3470A-LTE’s two DC inputs. Top and front views of the terminal block

connector are shown here.

STEP 1: Insert the negative/positive DC wires

into the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose,

use a small flat

blade screwdriver to tighten the

wire

-clamp screws on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on the OnCell

G3470A

-LTE’s top panel.

ATTENTION

Before connecting the

OnCell G3470A-LTE to the DC power

inputs, make sure that the DC power source voltage is stable.

Wiring the Relay Contact

The OnCell G3470A-LTE has one relay output, which consists of the two

contacts of the terminal block on the OnCell G3470A-LTE’s top panel.

Refer to the Specification section for detailed electrical requirement. The

relay contacts are used to indicate user-configured events. The two wires

attached to the relay contacts form an open circuit when a

user-configured event is triggered. If a user-configured event does not

occur, the relay circuit will be closed.

Wiring the Digital Inputs

The OnCell G3470A-LTE has two sets of digital inputs—DI1 and DI2. Each

DI comprises two contacts of the 6-pin terminal block connector on the

OnCell G3470A-LTE’s top panel. Refer to the Specification section for

detailed information on isolated digital input definition.

- 10 -

Communication Connections

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the OnCell G3470A-LTE’s front

panel are used to connect to Ethernet-enabled devices.

Below we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports.

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

1000BaseT Ethernet Port Connection

1000BaseT data is transmitted on differential TRD+/- signal pairs over

copper wires.

MDI/MDI-X Port Pinouts

Signal

TRD(0)+

TRD(0)-

TRD(1)+

TRD(2)+

TRD(2)-

TRD(1)-

TRD(3)+

TRD(3)-

RS-232 Connection

The OnCell G3470A-LTE has one RS-232 (8-pin RJ45) console port

located on the front panel. Use either an RJ45-to-DB9 or RJ45-to-DB25

cable to connect the Moxa OnCell G3470A-LTE’s console port to your PC’s

COM port. You may then use a console terminal program to access the

OnCell G3470A-LTE for console configuration.

Console Pinouts for 10-pin or 8-pin RJ45

10-Pin

Description

8-Pin

–

DSR

RTS

GND

TxD

RxD

DCD

CTS

DTR

–

Altri manuali per OnCell Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Moxa Technologies Portale

Moxa Technologies

Moxa Technologies AIG-100 Series Manuale utente

Moxa Technologies

Moxa Technologies MGate 5122 Series Manuale utente

Moxa Technologies

Moxa Technologies MGate W5108 series Manuale utente

Moxa Technologies

Moxa Technologies OnCell G3470A-LTE-EU-T Manuale utente

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN-T Manuale utente

Moxa Technologies

Moxa Technologies NPort PCG Manuale

Moxa Technologies

Moxa Technologies OnCell Series Manuale utente

Moxa Technologies

Moxa Technologies MGate 5103 Manuale utente

Moxa Technologies

Moxa Technologies MGate MB3000 Modbus Manuale utente

Moxa Technologies

Moxa Technologies MGate 5109 Manuale utente

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP Manuale utente

Moxa Technologies

Moxa Technologies OnCell G3150A-LTE Manuale utente

Moxa Technologies

Moxa Technologies Mgate MB3660 Manuale utente

Moxa Technologies

Moxa Technologies MGate MB3280 Manuale utente

Moxa Technologies

Moxa Technologies MGate MB3180 Manuale utente

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP Manuale utente

Moxa Technologies

Moxa Technologies NPort 4511 Manuale utente

Moxa Technologies

Moxa Technologies NPort 5600-8-DTL Series Manuale utente

Moxa Technologies

Moxa Technologies MGate 4101-MB-PBS Manuale utente

Moxa Technologies

Moxa Technologies MGate 5134 Series Manuale utente

Moxa Technologies

Moxa Technologies MGate 5109 Manuale utente

Moxa Technologies

Moxa Technologies MGate MB3170 Manuale utente

Moxa Technologies

Moxa Technologies UC-8410 Manuale utente

Moxa Technologies

Moxa Technologies MGate MB3280 Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente