Moxa Technologies TRC-2190 Series Manuale utente

P/N: 1802001900013

*1802001900013*

TRC-190/2190 Series

Quick Installation Guide

Rackmount chassis for the NRack System™

Edition 5.1, May 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Introduction

Overview

Moxa’s NRack System includes the TRC-190/2190 Series, which is a

19-inch, rack-mountable chassis for selected Moxa media converter

slide-in modules. The TRC-190/2190 Series allows the network

administrator to connect various copper and fiber-optic network media

over protocols that include RS-232, RS-422, and RS-485. Support for

additional protocols will be available in the future. The TRC-190/2190

Series provides installation space for up to 19 single-slot media converter

slide-in modules in the front of the unit.

The TRC-190/2190 Series is equipped with an AC or DC power supply

installed in the back of the chassis. An extra installation space is available

for an optional redundant power supply (AC or DC).

Last but not least, the TRC-190/2190 also comes with a grounding lug to

provide grounding for the chassis.

Package Checklist

The Moxa TRC-190/2190 Series products are shipped with the following

items:

Standard Accessories

•TRC-190/2190 Series with one AC or DC power supply in the back of

the chassis

•18 units of chassis face plates and screws

•Rackmount kit

•Power cord (for the TRC-190/2190-AC only)

•Quick installation guide (printed)

•Warranty card

Optional Accessories

•PWR-190/2190-AC: Redundant AC Power Supply Module

•PWR-190/2190-DC-xx: Redundant DC Power Supply Module

NOTE: Notify your sales representative if any of the above items are

missing or damaged.

- 3 -

Slide-in Modules Installation

Installing or Removing Chassis Face Plate

Install a chassis face plate over any unused slot by aligning the hole in the

face plate with a threaded hole in the chassis. Secure the face plate with

the enclosed screw.

ATTENTION

Each slot in the TRC

-190/2190 Series chassis without a slide-

module installed MUST have a chassis face plate covering the

empty slot for Class A compliance.

Remove the front plate by loosening the screw before installing any

slide-in module. We suggest storing the removed face plates together in

case you need to use them again.

Installing the Media Converter Slide-in Modules

ATTENTION

Wear a grounding device and observe electrostatic discharge

precautions when installing or replacing the media converter

slide

in modules into the chassis. Failure to observe this caution

could result in damage to, and subsequent failure of, the media

converter slide-in modules.

Instructions to install the media converter slide-in module into the

TRC-190/2190 chassis are as follows:

1. Slide-in modules can be installed in any empty slot of the chassis in

any order.

- 4 -

2. Before installing the slide-in module, make sure the front plate has

been removed. Please refer to the previous Installing or

Removing Chassis Face Plate section.

3. Align the slide-in module with the chassis installation slot so that the

panel fastener screw is at the top of the module.

4. Carefully slide the slide-in module into the slot while aligning the

module’s circuit board with the installation guide.

5. Ensure the slide-in module is firmly seated inside the chassis.

6. Push in and rotate the attached panel fastener screw clockwise to

secure the module to the chassis.

7. Repeat step 3 to 7 for any additional media converter slide-in

module.

Replacing the Media Converter Slide-in Modules

To replace a media converter slide-in module in the TRC-190/2190

chassis:

1. Remove the slide-in module to be replaced by loosening the panel

fastener screw that secures the module to the chassis. Slide the

module out from the chassis.

2. Align the replacement slide-in module with the chassis installation

slot so that the panel fastener screw is at the top of the module.

3. Carefully slide the slide-in module into the slot while aligning the

module’s circuit board with the installation guide.

4. Ensure the slide-in module is firmly seated inside the chassis.

5. Push in and rotate the attached panel fastener screw clockwise to

secure the module to the chassis.

Powering the TRC-190/2190

The TRC-190/2190-AC chassis is equipped with an AC power supply in the

back of the chassis. When the power supply module is correctly installed

in the back of the chassis, powering on the power supply module will

power on the whole TRC-190/2190-AC.

AC Power Supply Modules

The AC power supply module includes:

•An AC power module that supports 110 to 220 VAC input and supplies

power to the chassis and installed media converter slide-in modules.

•An AC power connector with a fuse holder.

•A power cord.

•An ON/OFF switch, which allows the module to supply power to the

chassis and slide-in modules when set to “l”.

•A power LED indicator.

•An additional fuse installed in a fuse holder on the PCB of the module.

Optional Redundant Power Supply Module

An extra space is available at the right side of the back of the chassis to

install an optional power module, the PWR-190/2190-AC. The

specification is the same as the one that comes with the

- 5 -

TRC-190/2190-AC chassis. The PWR-190/2190-AC and

PWR-190/2190-DC-48 power modules can be installed at the same time.

Powering the AC Power Supply Module

ATTENTION

Ensure that the ON/OFF switch is set to “

O”

before connecting to

the external power source. Failure to observe this caution could

result in damage to, and subsequent failure of, the AC power

supply module and human life.

To power on the power supply modules:

1. Set the ON/OFF switch to “O”.

2. Connect the female end of the power cord to the AC power connector

on the power supply module.

3. Plug the male end on the power cord into the correct voltage AC rack

or wall socket.

4. Set the ON/OFF switch to “l”.

5. Check whether or not the power LED is illuminated to see if the

power supply module is working.

DC Power Supply Modules

The TRC-190/2190-DC-xx is equipped with a DC power supply in the back

of the chassis. When the power supply module is correctly installed in the

back of the chassis, powering on the power supply module will power on

the whole TRC-190/2190-AC.

The DC power supply module includes:

•A DC power module that supports 36 to 53 VDC input and supplies

power to the chassis and installed media converter slide-in modules.

•A DC power connector.

•An ON/OFF switch, which allows the module to supply power to the

chassis and slide-in modules when set to “l”.

•A power LED indicator.

- 6 -

Optional Power Supply Modules

An extra space is available at the right side of the back of the chassis to

install an optional power module, the PWR-190/2190-DC-xx. The

specification is the same as the one that comes with the

TRC-190/2190-DC-xx chassis. The PWR-190/2190-AC and

PWR-190/2190-DC-48 power modules can be installed at the same time.

Powering the DC power supply module

ATTENTION

•

Before connecting to the external power source, ensure that

the ON/OFF switch is set to “O”. Failure to observe this

caution could result in damage to, and subsequent failure of,

the DC power supply module and human life.

•

This product is intended to be used in a restricted access

location. Proper grounding (earth ground) is required to

ensure safe operation. A grounding terminal is provided for

proper grounding of the device as per customer installation

requirements and local electrical codes. Before installation,

use a voltmeter/ohmmeter to check the wiring.

To power on the power supply modules:

1. Set the ON/OFF switch to “O”.

2. Be sure that the external power source is NOT powered.

3. Connect the power cord and the shielding ground to the male

terminal block.

4. Link the male and female terminal blocks.

5. Tighten the screws (clockwise) to secure the male and female

terminals.

6. Power up the external power source.

7. Set the ON/OFF switch to “l”.

8. Check whether or not the power LED is illuminated to see if the

power supply module is working.

Power Supply Module Installation

ATTENTION

Do not connect the power supply module to the external power

source before installing it into the chassis. Failure to observe this

may cause equipment damage, personal injury or even death.

- 7 -

1. Install the AC power supply module and DC power supply module

the same way. The default power supply module will be at power

module Slot A. We can install an additional power supply module in

Slot B. You can install the power supply module or remove it from

Slot A or Slot B in the same manner.

2. When installing a power supply module to Slot A or Slot B, be sure

that the there is no plate installed in the specific slot. If there is,

remove the plate first. To remove the plate, remove the two screws

that secure the plate to the chassis.

3. Where there is no plate on the chassis, slide the power supply

module slowly and follow the installation guide in the chassis. Push

the power supply module into the chassis till the end and ensure that

the power supply module is firmly connected to the chassis.

4. Screw the power supply module clockwise and fix the power supply

module.

5. Connect the power supply module to the external power source.

Power Supply Module Replacement

Replace the AC power supply module or DC power supply module by the

same way. Do not remove the power supply module from chassis when

the power source is connected and the external power switch is set to “O.”

1. Set the power supply module power switch to “O.”

2. Disconnect the power supply module from the external power

source.

3. Loose the two screws on the power supply module.

- 8 -

4. Slide the power supply module smoothly.

5. Install another new power supply module following the instructions

in the previous section.

Power Supply Fuse Replacement

(TRC-190/2190-AC, power supply module only)

To replace a fuse on the power supply module does not require to pull the

power supply module out of the chassis.

Replacing the Fuse

ATTENTION

Wear a grounding device and observe electrostatic discharge

precautions when replacing the fuse in the power supply module.

Failure to observe this caution could result in damage to, and

subsequent failure of, the power supply module.

Follow the instructions below when you need to change the fuse:

1. Set the power switch on the power supply module to “O”.

2. Disconnect the power supply module from the external power

source.

3. Remove the fuse from the holder carefully.

4. Install a same-sized fuse with the same current rating in the fuse

holder.

NOTE

Failure to use a fuse of the same size and same rating may

damage your power module or even the entire equipment setup.

5. Connect the power supply module to the external power source.

ATTENTION

Do not connect the power supply module to the external power

source before installing it into the chassis. Failure to observe this

may cause the equipment damage, personal injury, or even

death.

TRC-190/2190 Rackmounting

Installing the TRC-190/2190 Chassis

The TRC-190/2190 Series can be installed in a standard 19-inch rack.

NOTE

Rackmounted equipment must be reliably grounded. Power

supply connections other than direct connections to the branch

circuit (e.g., use of power strips) should be employed.

The TRC-190/2190 Series chassis is designed so that the installation

brackets can be installed to align the chassis either flush against the front

of the rack or recessed from the front of the rack.

- 9 -

ATTENTION

Select mounting bracket locations on the chassis that will keep

the chassis balanced when mounted to the rack. Failure to

observe this warning could allow the chassis to fall, resulting in

equipment damage and/or possible injury to personnel.

To install the TRC-190/2190 chassis into a standard 19-inch rack:

1. Determine the preferred alignment of the chassis in the rack.

NOTE

Installation bracket mounting screws are provided. Rackmount

screws and clip nuts are NOT provided.

2. Locate four (4) installation bracket mounting screws (provided) for

each chassis to be installed.

ATTENTION

Mount the chassis evenly and securely onto the rack. Failure to

observe this warning could allow the

chassis to fall, resulting in

equipment damage and/or possible injury to personnel.

3. Align the mounting bracket in the selected position against the side

of the chassis so that the chassis installation holes are visible

through the bracket installation holes.

4. Using a Phillips (crosshead) screwdriver, install the four (4) screws

through the mounting bracket into the installation holes on the side

of the chassis.

5. Repeat step 3 and step 4 for the second mounting bracket.

6. Carefully align the chassis at a secure and level position between the

19-inch site rackmounting rails.

7. Install two (2) screws through the bracket at each side into the

mounting rail, using the clip nuts to secure, if necessary.

- 10 -

Grounding

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices. Attach

the grounding wire (12 AWG copper wire gauge or larger) to the chassis

grounding lug carefully.

Troubleshooting

General Troubleshooting

Condition

Try this

1. The LED indicator

on power supply

module is not

illuminated.

•Check if the power cord is correctly connected

to the power source.

•Check if the power source is supplying power.

•Check if the fuse in the fuse holder is not

damaged.

•Check if

the power switch on the panel is set to

“l”.

•If none of the above, please contact y

our local

distributor/reseller or our technical support

staff.

The power LED

indicator on the

slide-

in module is

not illuminated.

•

Check if the LED indicator on the power supply

module is illuminated. If no, follow the steps

for Condition 1.

•Check if the power supply module is really

connected to the panel.

•Check if the slide-in module is correctly

attached to the chassis.

•If none of the above, please contact our local

distributor/reseller or our technical support

staff.

3. The power LED

indicator on the

front panel is

illuminated, but

the data

transmission is

not working.

•Check if the cables are correctly attached to

the slide-in module.

•Check the pin-assignment of the serial cable

•Check if the OP Mode switch

on the front panel

is correctly set for your operation.

•Check if the fiber patch cord is not damaged.

•Check if the length of the fiber cable is under

our claimed distance.

•If none of above, please contact our local

distributor/reseller or our technical support

staff.

Specifications

Physical Characteristics

Housing

SECC (1.2 mm)

Dimensions

440 x 260 x 88 mm (17.32 x 10.24 x 3.46 in)

Weight

5.2 kg (11.4 lb), with one power module installed

Number of Slots

TRC-190: 19 slots on the front for slide-in modules.

TRC-2190: 18 slots on the front for slide-in module

and 1 slot for the CSM-MN01 management card

2 slots at the back for power supply modules

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Moxa Technologies Hardware di rete

Moxa Technologies

Moxa Technologies AWK Series Manuale utente

Moxa Technologies

Moxa Technologies DA-661-CE Manuale utente

Moxa Technologies

Moxa Technologies NPort 5610-8 Manuale utente

Moxa Technologies

Moxa Technologies AWK-6232-M12 Manuale utente

Moxa Technologies

Moxa Technologies UC-7110 Series Manuale utente

Moxa Technologies

Moxa Technologies UC-7420/7410 Manuale utente

Moxa Technologies

Moxa Technologies Airworks AWK-3131A-M12-RCC Manuale utente

Moxa Technologies

Moxa Technologies NE-4100 Series Manuale utente

Moxa Technologies

Moxa Technologies EOM-G103-PHR-PTP Series Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C Manuale utente

Moxa Technologies

Moxa Technologies UC-8580 Series Istruzioni per l’uso

Moxa Technologies

Moxa Technologies IA3341 Istruzioni per l’uso

Moxa Technologies

Moxa Technologies ThinkCore DA-660-8-CE Manuale utente

Moxa Technologies

Moxa Technologies EOM-G103-PHR-PTP Series Manuale utente

Moxa Technologies

Moxa Technologies NPort IA 5250 series Manuale utente

Moxa Technologies

Moxa Technologies NPort Express DE-211 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-5222 Manuale utente

Moxa Technologies

Moxa Technologies INJ-24A Series Manuale

Moxa Technologies

Moxa Technologies MRC-1002 Series Guida rapida

Moxa Technologies

Moxa Technologies ioMirror E3210 Manuale utente

Moxa Technologies

Moxa Technologies MiiNePort E3 Series Manuale utente

Moxa Technologies

Moxa Technologies MXNVR-RO Manuale utente

Moxa Technologies

Moxa Technologies NPort W2150A-W4 Series Manuale utente

Moxa Technologies

Moxa Technologies V91 Guide Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente