MultiTable Keyboard & Mouse Tray Manuale utente
The Height of Healthy Design®
MultiTable Keyboard & Mouse Tray
ASSEMBLY INSTRUCTIONS
PARTS AND TOOLS
PLEASE REVIEW these instructions before beginning the installation. Check that all
parts needed were provided with your order. Parts are listed on page 2 and 5
of the assembly instructions. Contact MultiTable if any parts are missing. Do not
discard the packaging until satisfied that the product operates to your satisfaction.
The Keyboard and Mouse Tray combines an articulating arm with a
keyboard platform. In this assembly manual, installation of the two
products will be explained in sequence, beginning with the articulating arm.
Articulating Arm ( 1 )
Front Stop ( 1 )
Track (1)
Track Extender ( 1)
*Includes Extras
Cord Clip ( 1 )
Rear Bumper* (1)
ADDITIONAL TOOLS REQUIRED
*Optional
CAUTION:
This install requires a
power drill. This is not
a hand tool install.
STEP 1: Drill Pilot Holes for Attaching Track
•Drill with 1/8'' bit
• #2 Phillips bit
•Position one end of the track ½" from the front
edge of the work surface.
•Drill 1/8'' pilot holes through the seven holes
indicated in the illustration.
-Drill the holes 5/8" deep.
CAUTION: Be careful not to drill
through the top of the work surface.
Underside of
With this short 13" track, the track
extender is normally used as the rear
stop. If the rear bumper will be used
instead, drill a pilot hole in the center rear
hole through the track into the bottom of
the worksurface and do not drill pilot holes
in the two rear side holes.
Work Surface
Front
Rear
2
Optional Rear Hole for
Rear Bumper.
⅝ Wood
Screws (20*)
MultiTable Keyboard & Mouse Tray
PARTS PROVIDED
ASSEMBLY MultiTable Keyboard & Mouse Tray
STEP 2: Attach Track
•First attach the track through
the four center holes, as shown.
•Then attach the track extender
through the two
rear holes.
•Do not attach a screw through
the front center hole at this time.
STEP 3: Install Articulating Arm
•Slide the articulating arm onto the
track. Position it back far enough so
that you have access to the front
center hole on the track.
STEP 4: Attach Front Stop
•Position the front stop onto the
front of the track and secure it
with a screw through the center
hole.
•Drill pilot holes for the two side
screws and attach the ends of the
front stop with two more screws.
:'
Drill & Attach This Screw First
Optional Rear Bumper
Placement
Slide
3
MultiTable Keyboard & Mouse
Tray ASSEMBLY
STEP 5: OPERATION
•Loosen the ratchet handle, adjust the tilt angle, then tighten the handle.
To Telescope:
•Lift the front of the platform and slide it inward to stow or outward to access.
To Raise:
•Grasp both sides of the platform and raise to the desired height.
To Lower:
•Grasp both sides of the platform, tilt up the front, and move down to the
desired height.
To De-activate Positive Tilt Lock-out:
•Rotate tab ¼ turn to the right. Refer to diagrams below for further explanation:
TAB ROTATED
DOWN FOR
POSITIVE AND
NEGATIVE TILT--
TAB ROTATED UP
FOR NEGATIVE TILT
ONLY
4
To Tilt:
ASSEMBLY MultiTable Keyboard & Mouse Tray
PARTS PROVIDED
Keyboard Platform ( 1 ) Palm Rest ( 2)
1 for Keying and 1 for Mousing
Flathead Screw (4) Flange Nut (4) Panhead Screw (4) Cord Clips (2)
#8-32x½ #8x32 #8-32x
5
/8
CAUTION: Hand-tighten screws only. Do not use power tools.
ADDITIONAL TOOLS REQUIRED
•Phillips screwdriver
STEP 5: Attach Palm Rest(s)
5
•Attach the palm rest(s) to the keyboard platform. Use the #8-32x
5/8
panhead screws and a Phillips screwdriver. Six screw holes are
located in the keyboard platform to accommodate a
•variety of installation possibilities.
©
-With one palm rest, attach it with two
screws through the two end holes.
-With two separate palm rests, attach
each with two screws,
as shown.
-The mouse and keyboard
palm rests may be attached
on either the left or right sides
of the keyboard platform.
Panhead
Screw
PLEASE REVIEW these instructions before beginning installation. Check that all
parts needed were provided with your order. Contact MultiTable if any parts are
missing.
MultiTable Keyboard & Mouse Tray ASSEMBLY
STEP 6: Attach Keyboard Platform
•Attach the keyboard platform to the keyboard arm and track
assembly using the four flathead screws and flange nuts.
-Be sure the flange on the nuts is facing upward.
IMPORTANT: The flange nuts must be fully tightened to ensure the
nuts are locked. Use a Phillips screwdriver.
6
ASSEMBLY MultiTable Keyboard & Mouse Tray
7
STEP 7: Manage Cables
•Adhere cord clips to the
underside of the keyboard
platform as needed to organize
the keyboard and mouse cables.
OPERATION
To Tilt:
•Loosen the ratchet handle, adjust the
tilt angle, then tighten the handle.
To Telescope:
•Lift the front of the platform and slide it inward to stow or outward to
access.
To Raise:
•Grasp both sides of the platform and raise to the desired height.
To Lower:
•Grasp both sides of the platform, tilt up the front, and move down to
the desired height.
The Height of Healthy Design
®
Quality Design
I
Free Shipping
I
30-Day No Risk Returns
I
Over 85,000 Sold
855-469-6858
I
I
www.MultiTable.com
MultiTable, LLC I 2255 W Desert Cove Ave., Suite E, Phoenix, AZ 85029
© 2019 MultiTable. All rights reserved. MultiTable Keyboard & Mouse Tray- Assembly v-3
Indice
