Muncie OMNI-SYSTEM PLUS Guida rapida
OMNI-SYSTEM PLUS
SNOW & ICE DIVISION
OPERATION AND
CONFIGURATION MANUAL
PAGE 1 OMNI-SYSTEM
SNOW & ICE DIVISION PAGE 2
TABLE OF CONTENTS
Controller Specications and Features.......................................................................................4
Controller Navigation/Button Assignments................................................................................ 5
Body Selection and Diagnostics Connection............................................................................. 6
Main Operating Screen—Standard Spreader Body....................................................................7
Main Operating Screen—Anti-ice/Tow Plow ...............................................................................8
Main Operating Screen—Directional Body/Sprayer................................................................... 9
Main Operating Screen—External Equipment Body/Uncontrolled Body............................... 10
Operator Adjustments/Datalogging Screens............................................................................ 11
Accessing and Navigating Conguration Menu/Firmware Updates....................................... 12
System Proles............................................................................................................................13
Wi-Fi conguration......................................................................................................................14
Datalogging Setup.......................................................................................................................15
Global Spreader Settings.......................................................................................................16-18
Granular Rate/Liquid Rate Setpoints.........................................................................................19
Conguration Per Body Selection ........................................................................................20-25
Cylinder Congurations (Plow and Hoist) ...........................................................................26-27
System Alerts...............................................................................................................................28
Notes.............................................................................................................................................29
PAGE 3 OMNI-SYSTEM
SNOW & ICE DIVISION PAGE 4
FEATURES & SPECIFICATIONS
Controller Specications
• Color Touchscreen Display
• Uses LED Back Lighting
• Tactile Switch Controls
• Built-in Audible Alarm
• Ergonomic Control Design
• GPS based Data-Logging
• Wi-Fi Connectivity
• CANBUS Platform
• Air & Road Temperature Sensor Ready
Controller Features
• Congurable Error Status Indicators
• Open & Short Circuit Protection and Alerts
• Current Compensated, Pulse Width Modulated Outputs
• System Sources Current to Valve Coils
• Upgradeable Software
• Data Downloading through Wi-Fi & USB Drive
• Real-time Wi-Fi Support Line
• AVL System Ready
• Ground Speed Orientation
• Programmable Body Congurations
• Open/Closed Loop Spreader & Liquid Operation
• Expandable I/O
PAGE 5 OMNI-SYSTEM
CONTROLLER OPERATION
CONTROLLER NAVIGATION:
Cycle Screens: Depress the Auger or Spinner
to cycle screens.
Adjustments: Tap the appropriate touch screen
button to change settings. Hydraulic performance
settings can be adjusted in the conguration menu.
Operation: Use the appropriate buttons and rotary
knobs to control the spreader operation.
BUTTON ASSIGNMENTS:
Spreader: Press to initiate the spreader system.
Blast: Press to “Blast” or increase the granular rate to a
congurable set point for an adjustable time.
Pause: Press to pause or un-pause all spreader
operations.
Blast
Cycle Screen
Back
Spreader Pause
Cycle Screen
Forward
SNOW & ICE DIVISION PAGE 6
Body Selection & Diagnostic
Connection:
This following screen should be referenced
before any operation to ensure the “Body”
selection type is correct for the given body
that is currently being operated. Selecting the
wrong body type could result in unintended
machine operation.
Body Selection – Depress the Body Selection
button to sequence through dierent body
conguration. Note: Available body type discussed
later in the document and are precongured by
Muncie Technicians before system ships. Alternate
body congurations can be added by contacting
the Muncie Power Products Snow and Ice team.
Diagnostic Connection – This feature allows
the user to connect to Muncie for diagnostic
purposes. Simply connect to a Wi-Fi network and
press the Start button to connect to Muncie for
Diagnostic help.
Remote Connection Status – Displays the current
state of the wireless connectivity (Muncie Use Only).
CONTROLLER OPERATION
PAGE 7 OMNI-SYSTEM
CONTROLLER OPERATION
Main Operating Screen – Standard
Spreader Body:
Air Temp/Road Temp – Displays air and
road temperatures. Temperatures will only
display if IR temperature sensor is installed.
Trip Totals – Displays the material and liquid
totals per trip. Simply tap to reset. Keep in
mind that resetting these totals doesn’t reset
the spreader datalog.
Joystick Mode – Displays the current piece
of equipment the joystick is controlling.
Wi-Fi Strength – Displays the Wi-Fi
signal strength.
System Pressures/Oil Temperature –
Toggle this selection to alternate between
system pressures and oil temperature.
Message Bar – Displays error messages.
Spinner Rate – Displays the spinner rate as
a percent or lane coverage.
Pre-Wet Rate – Displays the pre-wet rate.
Product Type – Displays the material being
spread. Tap to change products available.
Auger Rate – Displays the auger rate. In
manual mode, the setting is displayed as
a percentage. In auto mode the rate is
displayed as Lbs/Mile. Keep in mind that this
value will remain constant, but the material
discharged will vary per vehicle speed to
maintain a constant output per mile.
Mode – Displays the mode of operation.
Toggle button to change between Auto
and Manual.
Hot Buttons – Buttons can be congured
on the touchscreen for additional system
functionality.
Time – Displays the current time.
Message
Bar
Time
Hot
Buttons
Vehicle
Speed
Body
Type
Joystick Wi-FiSystem
Pressure/
Oil
Temps
Mode
Product
SNOW & ICE DIVISION PAGE 8
MAIN OPERATING SCREENS
Main Operating Screen – Anti Ice:
Air Temp/Road Temp – Displays air and road
temperatures. Temperatures will only display if IR
temperature sensor is installed.
Joystick Mode – Displays the current piece of
equipment the joystick is controlling.
System Pressures/Oil Temperature –
Toggle this selection to alternate between
system pressures and oil temperature.
Message Bar – Displays error messages.
Liquid Rate – Displays the liquid rate. Use the auger
rate knob to control the speed of the liquid output.
Mode – Displays the mode of operation. Toggle
button to change between Auto and Manual.
Boom Controls – Up to 3 booms can be congured with
the system. Booms can either be controlled with on screen
touch buttons or switch controls. Press appropriate boom
controls to actuate. When a boom is actuated, the button
will latch orange to indicate that it is “on”.
Main Operating Screen – Tow Plow:
Air Temp / Road Temp – Displays air and road
temperatures. Temperatures will only display if IR
temperature sensor is installed.
Joystick Mode – Displays the current piece of
equipment the joystick is controlling.
System Pressures / Oil Temperature – Toggle this
selection to alternate between system pressures
and oil temperature.
Message Bar – Displays error messages.
Auger Rate – Displays the auger rate. In manual
mode, the setting is displayed as a percentage. In
auto mode the rate is displayed as Lbs/Mile.
Auger #2 Rate – Displays the auger rate for the tow
plow. In manual mode, the setting is displayed as a
percentage. In auto mode the rate is displayed as
Lbs/Mile.
Spinner Rate – Displays the spinner rate as a
percent or lane coverage.
Mode – Displays the mode of operation. Toggle
button to change between Auto and Manual.
Joystick
Mode Not
Shown
Liquid
Rate
Spreader
Mode
Wi-Fi
Air Temp/
Road
Temp
Boom
Controls
Message
Bar
PAGE 9 OMNI-SYSTEM
MAIN OPERATING SCREENS
Main Operating Screen –
Directional Body:
Air Temp/Road Temp – Displays air and road
temperatures. Temperatures will only display if IR
temperature sensor is installed.
Trip Totals – Displays the material and liquid
totals per trip. Simply tap to reset. Keep in
mind that resetting these totals doesn’t reset the
spreader datalog.
Joystick Mode – Displays the current piece of
equipment the joystick is controlling.
System Pressures/Oil Temperature –
Toggle this selection to alternate between
system pressures and oil temperature.
Message Bar – Displays error messages.
Product Type – Displays the material
being spread. Tap to change products.
Liquid Rate – Displays the liquid rate. Use the auger
rate knob to control the speed of the liquid output.
Mode – Displays the mode of operation. Toggle
button to change between Auto and Manual
Main Operating Screen – Spray Body:
Trip Totals – Displays the material and liquid
total per trip. Simply tap to reset. Keep in mind
that resetting these totals doesn’t reset the
spreader dialog.
System Pressures/Oil Temperature – Toggle this
selection to alternate between system pressures
and oil temperature.
Message Bar – Displays error messages.
Liquid Rate – Displays the liquid rate
Mode – Displays the mod of operation. Toggle
button to change between Auto and Manual.
Boom Controls – Up to 3 booms can be congured with
the system. Booms can either be controlled with on screen
touch buttons or switch controls. Press appropriate boom
controls to actuate. When a boom is actuated, the button
will latch orange to indicate that it is “On”.
Mode Body
Type
Joystick
Mode
Not Shown
System
Pressure/
Oil Temps
Lane
Adjustments
Liquid
Rates
Indice
Altri manuali Muncie Accessori per automobili
