MuxLab 500816 Manuale utente
© MuxLab Inc. 2016 94-000833-A/ SE-000833-A
8 Button RS232/IR
Control Panel
500816
8 Button RS232/IR Control Panel Installation & Operation Manual
© MuxLab Inc. 2016 2
SAFETY PRECAUTIONS
To insure the best use from the product, please read all instructions carefully before
using the device. Save this manual for further reference.
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install
this product near water. Keep the product away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Using supplies or parts not meeting the product’s specifications may cause damage,
deterioration or malfunction.
Refer all servicing to qualified service personnel.
Install the device in a place with good ventilation to avoid damage due to
overheating.
Unplug the power cord when left unused for a long period of time.
Do not put any heavy items on the unit or on extension cable.
Do not remove the housing of the device as you may be exposed to dangerous
voltage or other hazards.
Information on disposal of devices: do not burn or mix with general household
waste, please treat this device as normal electrical waste.
Unpack the equipment carefully and save the original box and packing material for
possible future shipment.
Please read this user manual carefully before using the product.
8 Button RS232/IR Control Panel Installation & Operation Manual
© MuxLab Inc. 2016 3
Contents
Introduction ...............................................................................................................41.
1.1. Introduction to the 8 Button RS232/IR Control Panel.....................................4
1.2. Features.........................................................................................................4
1.3. Package Content ...........................................................................................5
1.4. Installation......................................................................................................5
Specification..............................................................................................................62.
Panel Description......................................................................................................73.
3.1. Front Panel ....................................................................................................7
3.2. Rear Panel.....................................................................................................8
3.3. Side Panel .....................................................................................................9
Connections............................................................................................................104.
4.1. Safety Precautions.......................................................................................10
4.2. System Diagram ..........................................................................................10
4.3. Connections for Programming and Looping.................................................10
System Operation ...................................................................................................125.
5.1. USB Driver Installation.................................................................................12
5.2. Software Programming................................................................................12
5.2.1. Main Menu...................................................................................................13
5.2.2. Panel/Key setting.........................................................................................16
5.2.3. Action List ....................................................................................................18
5.2.4. Setting Events..............................................................................................19
5.2.5. Event List.....................................................................................................29
Panel Drawing.........................................................................................................316.
Troubleshooting & Maintenance..............................................................................327.
Regulatory Compliance ................................................................................................33
8 Button RS232/IR Control Panel Installation & Operation Manual
4
Introduction1.
1.1. Introduction to the 8 Button RS232/IR Control Panel
The programmable control panel is a Wall-Mounted Control Panel. Every button is
programmable and works either individually or together. The programmable control
panel is built with the following interface: three (3) RS232, One (1) RS485, Three (3)
Infrared, two (2) Relay, and one (1) mini USB for programming.
Please note that:
“RS232 (1)”and “IR2”share the same port, and cannot be used at the same
time.
“RS232 (2)”and “IR3”share the same port, and cannot be used at the same
time.
The 8 Button RS232/IR Control Panel can control MuxLab products, as well as third
party devices such as projectors, screens etc. It is an easy-to-use control device for
presentation show rooms, classrooms and boardrooms.
1.2. Features
Each button can be programmed to send bi-direction RS232 and RS485
commands simultaneously to control MuxLab and third party devices.
Each button can be programmed to send infrared codes and control the
relays simultaneously to control MuxLab and the third party devices.
Each button supports a built in infrared code and RS232 code learning
function, including baud-rate setting.
ID looping function. Up to 99 units may be chained (looped) and controlled
together, via an ID identification.
The unit may be programmed through the USB or RS232 port, via the Control
Panel PC Software.
The unit supports backlit buttons with easy to change customizable labels.
The backlit brightness is controllable.
Face-Plate Dimension: 11.4cm (H) x 7cm (W).
Antistatic case design: providing good protection for long-term and stable
performance.
8 Button RS232/IR Control Panel Installation & Operation Manual
5
1.3. Package Content
One (1) 8 Button RS232/IR Control Panel
Four (4) captive screw Terminal Block connectors
Three (3) IR Emitter probes
One (1) Button Label sheet
One (1) USB type Ato Mini USB cable
Eight (8) Button Caps
One (1) 12VDC, 2.0A Power Adapter with US, UK & Euro Blade.
One (1) User Manual
Please verify that the product and the accessories are all included; if not, please
contact your dealer.
1.4. Installation
Follow the steps to install the device:
First, cut a hole on the surface of where the unit is to be installed, such as on a
desktop or desk-side panel, etc. Cut to the size indicated by the cut-out diagram in
Figure 1.
Second, fit the unit into the cut-out and adjust it so that it is flush with the surface (see
Figure 2).
Next, screw the unit face-plate securely to the surface with two screws and nuts.
Lastly, connect the unit power connector to the provided 12VDC power supply, but
do not connect the 12VDC power supply to the AC power outlet at this time.
Figure 1 Cut-out diagram
Figure 2 Installation Guide
8 Button RS232/IR Control Panel Installation & Operation Manual
6
Specification2.
Devices
Matrix, Switch, DVD, projectors, monitors, TV.
Compatibility
Compatible with MuxLab & Third party products
Output Ports
Three (3) RS232 ports
One (1) RS485 port
Three (3) Infrared Emitter ports
Two (2) Relay ports
Control Ports
USB or RS232 (either may be used)
Connectors
One (1) 2-pin terminal block (3.81 mm) for Power
Two (2) 2-pin terminal blocks (3.81 mm) for Relay
Two (2) 5-pin terminal blocks (3.81 mm) for Serial & IR
One (1) USB Port for firmware upgrade
Power Supply
One (1) 110-240VAC to 12VDC/2.0A power supply with US,
UK & Euro Blade
Temperature
Operating: 0° to 40°C Storage: -20° to 70°C
Humidity: Up to 95% non-condensing
Enclosure
Metal
Dimensions
4.49” x 2.76” x 1.10” (114mm x 70mm x 28mm)
Weight
0.33 lbs (0.15 kg)
Compliance
Regulatory: FCC, CE, RoHS
Warranty
2 years
Order Information
500816 8 Button RS232/IR Control Panel
8 Button RS232/IR Control Panel Installation & Operation Manual
7
Panel Description3.
3.1. Front Panel
No.
Name
Description
1
Button
Crystal clear and luminescent, programmable buttons:
Each button can be independently programed using the
Control Panel PC Software. To do so run the application
and connect the computer via a USB or RS232
connection to the 8 button RS232/IR Control Panel (see
section 5 for details on using the Control Panel PC
Software, found on the MuxLab website).
Each label within a button can be easily changed.
Simply select the label you need and change it as
shown below:
①
8 Button RS232/IR Control Panel Installation & Operation Manual
8
3.2. Rear Panel
No.
Name
Description
1
Power
Power connector: 12VDC. Please make sure the “+”
and “-” are connected correctly (using the correct
polarity), in order not to damage the unit.
2
Relay
Low Voltage Relay.
3
Output Port
(Section 1)
RS232 (1)/IR2: RS232 (1) and IR2 share the same
port, the actual use depends on the configuration set
by the Control Panel PC Software. When configured
for RS232, it is a unidirectional transmission,
meaning data may be transmitted, but not received.
IR1: IR1 may be used to control devices, and can be
program via the Control Panel PC Software.
RS485: The RS485 can be programmed to control a
device via the RS485 port. The command set for
RS485 is the same as for RS232 (1).
4
Output Port
(Section 2)
The section includes two groups:
RS232 (2)/IR3: RS232 (2) and IR3 may be used to
control devices, or used for chaining (looping output).
①
④
③
②
8 Button RS232/IR Control Panel Installation & Operation Manual
9
No.
Name
Description
RS232 (2) and IR3 share the same port, the actual
use depends on the configuration set by the Control
Panel PC Software.
RS232 (3): RS232(3) may be used to control
devices, used for chaining (looping output), or to
connect to a computer when programming the 8
button RS232/IR Control Panel.
These two groups share the same ground.
3.3. Side Panel
No.
Name
Description
1
Mini USB
Communicates with the computer and may be used
to update the unit firmware, or used in conjunction
with the Control Panel PC Software to program the
buttons of the device.
Transmit the infrared data when learning IR
(Optional).
2
IR Sensor
Receives and learns IR codes, in order to build an IR
command database.
①
②
8 Button RS232/IR Control Panel Installation & Operation Manual
10
Connections4.
4.1. Safety Precautions
The system should be installed in a clean environment with temperature and humidity
levels within the specified operating range.
All devices should be connected before turning on power.
4.2. System Diagram
The programmable 8 Button RS232/IR Control Panel (also references here-in as
programmable Control Panel) can send commands to different ports at the same time.
Meaning, each button can send RS232 commands, RS485 commands, IR codes and
control the relays with a single push of one button. See the example system diagram
below (Figure 3).
Figure 3 Example System Diagram
4.3. Connections for Programming and Looping
The programmable control panel may be connected to a computer in order to program
Indice
Altri manuali MuxLab Pannello di controllo
