mxr Mini Iso-Brick M239 Manuale utente
M239 | Mini Iso-Brick 2
1WHITE LED indicates good input power connection
2Four 9V DC outputs
3One switchable 9V/18V DC output
49V/18V switch sets voltage output level of 9V/18V output
(indicated by green LED)
5INPUT jack 18V @ 2000mA power
6GREEN LEDs indicate good output power connection
2
5
6
3
1
4
External Controls
M239 | Mini Iso-Brick 3
Basic Operation
Connect included AC adapter into M239’s 18V INPUT jack.
Plug AC adapter into wall outlet; white INPUT LED indicates
good connection.
Connect up to four pedals requiring 9V power to the four 9V
OUT jacks using the included barrel-to-barrel cables.
Connect another pedal to the switchable 9V/18V output. Use
9V/18V slide switch to match pedal voltage (indicated by green
LED).
Included splitter cable can be used to connect two pedals to a
single output. Connect straight end to M239 output and right-
angle ends to pedals’ power inputs.
Whether connecting single pedal or multiple pedals via splitter
cable, always be sure pedal mA ratings do not exceed output
mA ratings.
WARNING: Some pedals may be damaged if powered using
voltage that exceeds level required by the manufacturer, e.g.
powering a 9V pedal with 18V. We highly recommend staying
at or below manufacturer’s stated voltage requirement. Dunlop
assumes no responsibility or liability for equipment damage
caused by misuse of M239.
The Mini Iso-Brick Power Supply requires an 18V
regulated power supply rated at 2000 mA, with
5.5mm x 2.1mm positive barrel, negative center plug.
The included power adapter can utilize a wide range
of wall power, from 100–240V at 47–63Hz. Comes with
switchable US/Japan, UK, EU, and Australian plugs.
Operation Power
M239 | Mini Iso-Brick 4
Basic Operation
Connection Notes
Included cables use industry standard 5.5mm x 2.1mm positive
barrel, negative center polarity plugs.
Each output features a green LED. When lit, this LED indicates
a good connection. If short-circuited or overloaded, this LED
will turn off.
M239’s four 9V outputs can handle up to 300mA each.
M239’s 9V/18V output can handle up to 800mA.
All outputs may be used simultaneously for a total power
output of 17.1 watts.
The M239’s foldback current limiting circuit (FBCL) provides
ultimate protection against power shorts and overloads. Even
at full load, the M239 operates coolly and quietly as a fully
regulated power supply.
Troubleshooting
The power LED fails to light.
Dead AC outlet. Try plugging into another outlet, or test
the outlet with another device like a lamp.
Faulty connection. Double check plugs to make sure
they are inserted securely.
Short-circuited output. Disconnect the cable from the
output whose blue LED is off.
Wait 5 to 10 seconds for the unit to reset, indicated when
the blue LED comes on.
Power provided to some effects, but not others.
Incompatible power plug. Check that the dimensions
and polarity of the pedals are compatible with the
provided cables.
Faulty cord. Check by swapping the power cable with
another known good cable.
Faulty jack on Iso-Brick Power Supply DC output jack.
Check by plugging the power cable into a different DC
jack.
Faulty jack on the pedal. Test by running the pedal off
battery power.
M239 | Mini Iso-Brick 5
Specifications
Input 18V At 2 Amps regulated supply (positive barrel negative center
5.5mm x 2.1mm plug)
Outputs 9-18V @ 800mA (switched)
(4) 9V @ 300 mA
(all positive barrel negative center 5.5mm x 2.1mm)
*Note: Using a split cable allows you to share one output with two devices. Remember
the straight plug is the end that goes into the Mini Brick DC output and the two 90° to
the effects (this helps minimize ground return current noise). position.
Indice
Altri manuali mxr Alimentazione elettrica
