NAMCO FINAL LAP 3 UPRIGHT Manuale utente

namco@

FINAL LAP” 3 UPRIGHT

Operators Manual

01992 NAMCO-AMERICA, INC.

No part of this publication may be reproduced by any mechanical, photographic or

electronic process, or in the form of a phonographic recording, nor may it be stored in

a retrieval system, transmitted, or otherwise copied for public or private use, without

permission from NAMCO-AMERICA, INC.

Published by:

NAMCO-AMERICA, INC.

3255-l Scott Blvd., Suite 102

Santa Clara, CA 95054-3013

TEL:

(408)496-6371

FAX:

(408)496-6399

Printed in the U.S.A.

CONTENTS

SPECIFICATIONS.. .......................................................................................................................

2. PRECAUTIONS

2-l

Caution When Installing.. .......................................................................................................

2-2 Caution When Handling ......................................................................................................... 2

3. INSPECTION .................................................................................................................................

4. INSTALLATION

4-l Installing Game Cabinet

.......................... ................................................... .......................

4-2 Preparing the Game for Operation ........................................................................................ 4

4-3 Connecting Two or More Games Together ........................................................................... 4

4-4

Power On/Off Switch Location..

..........................................................................................

J-5 Choosing the Car Color

......................................................................................................... 6

5. ADJUSTMENTS

5-1 Power On

...............................................................................................................................

5-2

Adjustment Switches on the Service Panel ........................................................................... 6

8-3

Test Mode and Play Options .................................................................................................

5-3-(3)-2

Bookkeeping for FINAL LAP 3 ........... ........................................................... 10

S-4 Monitor Adjustments ............................................................................................................ IO

lnfttattztng

Controls ..............................................................................................................

HOWTO

PLAY ............................................................................................................................ 12

7. MAINTENANCE

7-l

Opening the Control Panel .................................................................................................. 13

7-l-l

Shtft

Assembly.

........................................................................................................ 13

7-l-2 Steering Assembly

................................................................................................... 14

7-l-3

Steering Potentiometer............................................................................................ 14

7-2

Gas

Pedal Assembly .15

............ .............................................................................................

7-3

Removing

the

Game

PCB ................................................................................................... 15

7-4 Removing the Monitor 16

......... ..............................................................................................

7-5

Replacing the Speakers ...................................................................................................... 16

7-6

Replacing

the

Fluorescent

M-tract

Lamp

............................................................................. 16

TROUBLESHOOTING-GENERAL

........................................................................................... 17

8-l

Troubleshooting

power

............................................................................................... 18

9. PARTS

LIST

...............................................................................................................................

.21

10. GAME

HARNESS

WIRING DlAG&V.lS

...................................................................................

..2

11. LIST OF ILLUSTRATIONS (See over)

11.

LIST OF ILLUSTRATIONS

4-1 3/4 Front and Back View

of Game . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4-2

Link Connection

One Cabinet . . . . . . . . . .._................................................................................. 4

4-3

Link Connection

Two to up to Eight Cabinets .....................................................................

4-4 Car-Color Connectors

............................................................................................................ 6

5-1

Service Panel ........................................................................................................................

5-2 Game Option Screen .............................................................................................................

5-3 Table of Game Option Settings .............................................................................................

5-4 Switch Test Screen

...........................................................................................

..~

.................. 9

5-5 Monitor Remote Adjustment Board ..................................................................................... 10

5-6 Switch Test Screen

(Initialize Completed) ........................................................................

7-1 Opening the Control Panel .................................................................................................. 13

7-2

Shift Assembly............................................

........................................................................ 13

7-3 Steering Assembly

............................................................................................................... 14

7-4 Steering Potentiometer ........................................................................................................ 14

7-5 Gas Pedal Assembly

........................................................................................................... 15

7-6 Replacing Game PCB ......................................................................................................... 15

7-7

Replacing the Monitor.. ...............................................

.......................................................

.I6

7-8 Replacing Speakers/Fluorescent Lamp ............................................................................... 16

FINAL LAPm 3 UPRIGHT

1. SPECIFICATIONS

POWER SUPPLY:

POWER CONSUMPTION:

DIMENSIONS:

CRATED DIMENSIONS:

Monitor Cabinet Carton

SHIPPING WEIGHT:

MONITORS :

ACCESSORIES:

PC XT Type Switching Power Supply

Not to exceed

15OW,

12OVAC,

1.0 AMP

Width Depth

Height

lntv

I/4” 74”

Width Depth

Height

29” 37” 77”

325 lbs.

One (1) standard 25” Color Monitor

with auto degause and remote adjustment board

Keys: (Coin

Box)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

(Coin Door)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

(Rear Door) .._.............._..

..__.. . . . . . . . . . . . . . . . . . . . . . . . . . 2

Security Wrench ..,,,,................................................ 1

Link Cable

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . .1

Instrnction Manual

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Operators Quick Reference Card

..__........................

Note: Specifications may change without prior notice.

Modification and/or alteration of the FINAL LAP

3TM

game with kits or parts not supplied by NAMCO may

void the warranty.

2. PRECAUTIONS

2-l Caution when installing

This game is designed for indoor use only. The game must not be installed out-

doors or under the following conditions:

In areas directly exposed to sunlight, high humidity, direct water contact, dust,

high heat or extreme cold.

In locations that would present an obstacle in case of emergency, i.e. near fne

equipment or emergency exits.

On an unstable surface or subject to floor or other vibration.

2-2 Caution when handling

Power must always be turned off before replacing any parts or connecting/

disconnecting the connectors.

Do not subject game to physical shock when transporting or moving it.

c. The power supply range is between 1

lo-120V

AC.

The cabinet must be grounded with a securely connected ground plug.

Care must be taken at all times to avoid electrical shock whenever inspecting or

adjusting the game.

When unplugging the game from an electrical outlet, grasp the plug, not the

cord.

DO NOT attempt to repair the Printed Circuit Board (PCB) on site. It contains

sensitive chips that could easily be damaged by even the small internal voltage

of a multi-meter. Always return the PCB to your distributor for any repairs.

3. INSPECTION

The FINAL LAP 3 Game carton should be carefully inspected upon receipt to insure

that the game is complete and was delivered in good condition.

Inspect the game cabinet by doing the following:

Examine the cabinet exterior for dents, chips, or broken parts.

Unlock and open the rear service door, the front coin door, and the front dash panel

(unbolt 3 bolts) that swings forward and down.

Inspect the interior of the cabinet as follows:

Verify that all plug-in connectors (on the cabinet harnesses) are fiiy plugged

in. The connectors next to the PCB metal enclosure are for the car-color

selection. Any or none of the three connectors can be plugged into the harness

connector. (For more information, Ref. 4-5, Choosing the Car-Color).

DO NOT force connectors together. The connectors are keyed so they fit only

in the proper orientation. A reversed edge connector can damage a PCB and

will void your warranty.

Inspect the power cord to insure that there are no cuts or dents in the insulation.

c. Inspect the power supply connectors.

Inspect other major sub-assemblies, such as the video display monitors,

PCBs,

and speakers. Make sure that they are mounted securely and that all ground

wires are fiiy connected.

4. INSTALLATION

Installing Game Cabinet

Each Cabinet has two casters (one on each rear comer) and a Moving Assist

Handle located on the upper portion of the cabinet back to allow for easy

roll-

in and positioning of the game.

Tilt and roll the cabinet near to its intended operating position, and lower the

four (4) leg levelers, one on each comer of the cabinet, until the game rests

firmly on the floor.

Note that the cabinet design provides for front servicing through the “swing-

down” Control Panel illustrated below. This provides front access to the

Monitor Adjustment Board, the game PCB, and the Steering and Shift

Assemblies. This eliminates the need for the technician to move the game

away from the wall to service these components.

Remove the three (3) security bolts on the top edge of the Control Panel, and

carefully (its heavy) swing it down on its hinge to open.

Illustration 4-1,

3/4

FRONT and BACK VIEW OF GAME

J122

J121

IONE CABINET

4-2 Preparing the game for operation

If installing a single player FINAL LAP 3 unit, check the following:

Be sure all power is disconnected before making any adjustments.

b. Remove the monitor AC power cord, and plug it into the power supply.

Note the position of the Link PCB Switch located in the recessed metal box

opposite the power supply on the lower back panel of each Monitor Cabinet.

Each FINAL LAP 3 is shipped with the connector switch set for a single

cabinet operation, and should have the slide switch set in the “OUT” position.

Check to make sure it is set to “OUT” (see below).

Illustration 4-2, LINK CONNECTION

ONE CABINET

4-3 Connecting two (2) or more FINAL LAP 3s

Up to eight (8) FINAL LAP 3s can be interconnected (linked) to allow up to eight

(8) players to participate in the same race. When linking two or more games, the

following conditions must be met:

Each FINAL LAP 3 game should be connected to a separate power outlet.

Game difficulty and lap settings must be the same on all monitors in the

linked group. (Ref. 5-3-(2))

All connecting slide switches should be set to the “IN” setting.

Install the link cables between the FINAL LAP 3s by connecting an “OUT”

from one Monitor Cabinet to an “IN” of another game per the following

diagrams. Be sure to seat each plug solidly in its jack.

Perform the self-test by turning the power on to each game. Make sure that

the connections are properly made between games. (Ref. 5-3-1, Self-Test)

(CAUTION)

Make the Link Cable as short as possible to insure best signal transmission.

Link Cables transmit electronic data between games and are subject to elec-

tronic interference.

Install the Link Cable as far from other room cables as possible.

LINKING TWO CABINETS

LIIlimm

i_,,

Jlza

At,

LINK CABLE

LINKING THREE UP TO EIGHT CABINETS

LINK CABLE

Illustration 4-3, LINK CONNECTIONS

2 to UP TO 8 CABINETS

4-4 Power On/Off Switch location

The power supply is located inside the back of the cabinet and accessed through

the Rear Service Door.

The on/off switch is accessed through an opening on the lower right rear side (as

you face the game) of the cabinet.

45 Choosing the car color

Each player can select from one of four car colors. This is done by plugging in

different connectors (included with the game) into the car-color connector located

on the cabinet wall by the PCB enclosures, and accessed through the Front

Control Panel

The game, as shipped, has one connector plugged into the car-color harness and

the other two connectors attached to it.

The following are the car colors and their connectors:

l Light blue car. Plug in the connector with wires at all 4 pins.

l Blue and white car. Plug in the connector with wires at pins 2 and 4.

l Yellow car. Use NO connector.

l Red car. Plug in the connector with wires at pins 1 and 3.

YELLOW Car

USE NO CONNECTOR

icb

RED Car LIGHT BLUE Car

BLUE and WHITE

Car

Illustration 4-4, CAR-COLOR CONNECTORS

5. ADJUSTMENTS

5-l

Power on

When installation is complete, connect power cord to outlet and turn power on.

(Ref. 4-4

Power on/off Switch location)

5-2 Adjustment switches on the Service Panel

There are switches on the Service Panel located inside the coin door for adjust-

ment of the speaker volume, and for accessing the test mode.

Indice

Altri manuali NAMCO Console di gioco

NAMCO

NAMCO 90500146 Manuale utente

Manuali Console di gioco popolari di altre marche

Atari

Atari 2600 Manuale utente

PLAYNETIC

PLAYNETIC GameNetic Manuale utente

Sony

Sony SCPH-50008 Manuale utente

Nintendo

Nintendo Starlight Fun Center Manuale utente

Saitek

Saitek Alchemist Plus Manuale utente

Sears

Sears Tele-Games 637.99743 Manuale utente

AYANEO

AYANEO 2 Manuale utente

Sony

Sony PlayStation 3 (Uncharted: Drake's Fortune Limited Edition... Manuale utente

Mattel

Mattel My Meebas N2214 Manuale utente

Entex

Entex PacMan2 Manuale utente

Sega

Sega 32X Manuale utente

Saitek

Saitek Cougar Manuale utente

View-Master

View-Master Interactive Vision Schema elettrico

Sony

Sony SCPH-35003 GT Manuale utente

Sony

Sony PSP go Manuale utente

Sony

Sony PSVITA Manuale utente

Excalibur

Excalibur ABC Wide 333 Manuale utente

Microsoft

Microsoft XBOX Manuale del proprietario