National Instruments CFP-20xx Manuale utente

Quick Start Guide

FieldPoint cFP-20xx

What You Need to Get Set Up

•cFP-20xx LabVIEW RT controller

• Mounting hardware (DIN rail,

panel-mount, or rack-mount

accessory)

• I/O module(s)

•cFP-BP-xbackplane, connector

blocks, cables

• 11–30 VDC power supply

• Accessories: Ethernet cable,

number 2 Phillips screwdriver

• PC running Windows

• FieldPoint software 3.0.2 or later

•LabVIEWRT

™

cFP-20xx Quick Start Guide 2 ni.com

1. Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-xbackplane on a 35 mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the serial

number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to

connect the protective earth (PE) ground terminal on the cFP-BP-xbackplane to

the system safety ground. The backplane PE ground terminal has the following

symbol stamped beside it: . Connect the backplane PE ground terminal to the

system safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the

5/16 in. panhead screw shipped with the backplane to secure the ring lug to the

backplane PE ground terminal.

Caution Keep in mind these requirements for space and cabling

clearance:

• Allow at least 51 mm (2 in.) all around the backplane for air

circulation.

• Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the controller

for cabling clearance.

Cabling

Clearance

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

Cooling Outline

51 mm (2 in.)

Cooling Outline

51 mm (2 in.)

Min. 182 mm (7.18 in.)

106 mm (4.18 in.)

Cabling

Clearance

Cooling Outline

51 mm (2 in.)

All Around

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

127 mm

(5.00 in.)

Min. 165 mm

(6.50 in.)

cFP-20xx Quick Start Guide 4 ni.com

Mounting the Backplane on a Panel

1. Fasten the panel-mount plates to the back of the cFP-BP-xusing a number 2

Phillips screwdriver and the 8-32 × 5/16 in. countersink screws shipped with

the kit.

Caution Do not use screws longer than 5/16 in. to fasten the

panel-mount plates to the backplane.

TIONAL

INSTRUMENTS

102 mm

(4 in.)

457 mm (18 in.)

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

260 mm (10.25 in.)

102 mm

(4 in.)

cFP-20xx Quick Start Guide 6 ni.com

2. Bolt or screw the panel-mount accessory to a panel.

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

panel.

Mounting the Backplane on a DIN Rail

NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting

or rack mounting for the cFP-BP-8. The DIN rail mounting kit is NI part

number 778614-01.

1. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips screwdriver

and the 8-32 × 5/16 in. countersink screws shipped with the clip.

104.74 mm

(4.1 in.)

63.46 mm

(2.5 in.)

127.00 mm

(5.0 in.)

22.19 mm

(0.9 in.)

34.04 mm

(1.3 in.)

84.84 mm

(3.3 in.)

161.04 mm

(6.3 in.)

211.84 mm

(8.3 in.)

245.87 mm

(9.6 in.)

Caution Do not use screws longer than 5/16 in. to fasten the DIN rail

clip to the backplane.

2. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip.

3. Press down firmly on the backplane to compress the spring until the clip locks

in place on the DIN rail.

4. Connect the PE ground terminal on the cFP-BP-4 to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

TIONAL

INSTRUMENTS

cFP-20xx Quick Start Guide 8 ni.com

Mounting the Backplane in a Standard 19-in. Rack

1. Fasten the rack-mount bracket to the back of the cFP-BP-xusing the captive

screws on the bracket.

2. Bolt the rack-mount accessory to a standard 19-in. rack.

TIONAL

INSTRUMENTS

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

bracket.

TIONAL

INSTRUMENTS

cFP-20xx Quick Start Guide 10 ni.com

2. Install the cFP-20xx Controller on the Backplane

1. Make sure that no power is connected to the controller.

2. Make sure that the cFP-20xx controller is right side up with the NI logo at

the top, and align the captive screws on the controller with the holes on the

backplane.

3. Seat the card edge at the back of the controller in the card-edge connector on

the backplane.

4. Press the controller firmly to seat it on the backplane.

5. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.)

length, tighten the captive screws to 1.1 N · m (10 lb · in.) of torque.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali National Instruments Hardware per computer

National Instruments

National Instruments DAQ PCI-1200 Manuale utente

National Instruments

National Instruments NI PXIe-8130 Manuale utente

National Instruments

National Instruments NI-9146 Manuale del proprietario

National Instruments

National Instruments NI 9403 Manuale utente

National Instruments

National Instruments NI PXI-1042 Series Manuale utente

National Instruments

National Instruments PCMCIA-232 Manuale utente

National Instruments

National Instruments CPCI-GPIB Manuale utente

National Instruments

National Instruments SC-207 Series Manuale utente

National Instruments

National Instruments AT-GPIB Manuale utente

National Instruments

National Instruments MXI Express x4 Manuale utente

National Instruments

National Instruments PC/104-GPIB Manuale utente

National Instruments

National Instruments PXIe-5832 Manuale utente

National Instruments

National Instruments SCB-19 Manuale utente

National Instruments

National Instruments PXIe-7911 Manuale utente

National Instruments

National Instruments NI PXIe-1082 Manuale utente

National Instruments

National Instruments PCIe-1437 Manuale utente

National Instruments

National Instruments AT-GPIB/TNT Manuale utente

National Instruments

National Instruments NI 6711 Manuale utente

National Instruments

National Instruments USRP-2940 Manuale utente

National Instruments

National Instruments SCXI-1321 Manuale utente

National Instruments

National Instruments NAT7210 Manuale utente

National Instruments

National Instruments PXI-8170 Series Manuale utente

National Instruments

National Instruments PXIe-8100 Manuale utente

National Instruments

National Instruments PCI-1407 Manuale di istruzioni

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

Advantech

Advantech ASMB-935 Series Manuale utente

National Instruments cFP-20xx Manuale utente

Manuali Hardware per computer popolari di altre marche