National Instruments IC-3120 Manuale utente
USER MANUAL
IC-3120
Industrial Controller
This document contains detailed electrical and mechanical information for the National
Instruments IC-3120.
Contents
Hardware Overview.................................................................................................................. 1
Connector Pinouts............................................................................................................. 2
LED Indicators................................................................................................................14
Using the RESET Button................................................................................................ 19
Software Options.....................................................................................................................20
BIOS Configuration and System Recovery............................................................................ 20
Entering BIOS Setup.......................................................................................................20
BIOS Keyboard Navigation............................................................................................ 21
Main Menu......................................................................................................................21
Advanced Menu.............................................................................................................. 21
Boot Menu.......................................................................................................................22
Save & Exit Menu...........................................................................................................24
Restoring the NI Linux Real-Time Operating System....................................................25
Restoring the Windows Operating System..................................................................... 25
Mounting the IC-3120.............................................................................................................27
Securing the IC-3120 to a Mount....................................................................................31
Clearance Requirements................................................................................................. 31
Where to Go Next................................................................................................................... 32
Worldwide Support and Services............................................................................................ 32
Hardware Overview
The IC-3120 front panel consists of a VGA port, RJ50 serial port, two USB 2.0 ports, a
10/100/1000 Ethernet port, and two Gigabit Ethernet PoE ports.
The IC-3120 front panel also includes LEDs for communicating system status and a 44-pin
Digital I/O port. The Digital I/O port offers 8 isolated inputs, 8 isolated outputs, 2 bidirectional
differential I/O (RS-422) or single-ended input lines that can be used with a quadrature
encoder, and 8 bidirectional TTL lines.
Figure 1. IC-3120 Front Panel Connectors
RESET
DIGITAL I/O
10/100/
1000
ACT/
LINK
USER1
USER2
PWR/
FAULT
STATUS
PoE0
PoE PORT 0 PoE PORT 1
PoE1
5
3
6
1
2
4
IC-3120
Industrial Controller
1. VGA Connector
2. RS-232/RS-485 Serial Port
3. USB 2.0 Ports
4. Gigabit Ethernet Port
5. Gigabit Ethernet Ports with PoE
6. 44-pin Digital I/O Connector
Connector Pinouts
The IC-3120 provides the following connectors.
Chassis Grounding Screw
Use the grounding screw to connect the chassis to earth ground. An earth ground connection is
optional.
Note An earth ground connection does not connect C or CISO to earth ground.
2| ni.com | IC-3120 User Manual
Figure 2. Chassis Grounding Screw
SYSTEM
PoE
48 V
ISO
CISO CPoE
VPoE
VISO
5-24 V
12-24 V
C V
1
1. Chassis Grounding Screw
Power Input Connectors
The IC-3120 requires a power supply to power the system. If needed for your application,
additional power sources are required to enable Power over Ethernet and to power the isolated
outputs.
The same power supply may be used for both the system power and isolated outputs power if
isolation is not required and the power supply meets the voltage and power requirements for
both inputs. Refer to the IC-3120 Specifications for power requirements.
NI recommends the following power supplies for the IC-3120.
Power Supply Part Number
NI PS-15 Industrial Power Supply, to power the system or isolated outputs 781093-01
48 V, DIN Rail, Industrial Power Supply for Power over Ethernet 783307-01
48 V, Desktop Power Supply for Power over Ethernet 783308-01
IC-3120 User Manual | © National Instruments | 3
Figure 3. Power Connectors
SYSTEM
PoE
48 V
ISO
CISO CPoEV
PoE
V
ISO
5-24 V
12-24V
C V
1
3
2
1. System Power Connector
2. PoE Power Connector
3. Isolated Outputs Power Connector
Table 1. Power Connector Terminals
Terminal Description
C Common signal
V System power (12-24 VDC)
CISO Isolated common signal
VISO Power for isolated outputs (5-24 VDC)
CPoE PoE common signal
VPoE PoE power (48 VDC)
Ethernet Ports
The IC-3120 provides 3 Gigabit Ethernet ports. PoE PORT 0 and PoE PORT 1 are capable of
providing Power over Ethernet (PoE). The Ethernet ports provides a connection between the
IC-3120, a network, and other Ethernet devices. The IC-3120 automatically detects the speed
of the connection and configures itself accordingly.
The IC-3120 can power PoE-capable devices when a PoE power supply is connected. When
the IC-3120 supplies PoE, the LED that corresponds to the port illuminates. You can use non-
PoE Ethernet devices with the PoE-enabled Ethernet ports.
4| ni.com | IC-3120 User Manual
A CAT 5e or CAT 6 1000Base-T Ethernet cable is required to achieve 1,000 Mbps (Gigabit)
Ethernet performance. CAT 5 Ethernet cables are not guaranteed to meet the necessary
requirements. While CAT 5 cables may appear to work at 1,000 Mbps, CAT 5 cables can cause
bit errors, resulting in degraded or unreliable network performance.
(Windows only) The primary Gigabit Ethernet port provides Wake-on-LAN functionality from
the power off state when associated with the Intel® driver. Wake-on-LAN must be enabled in
the Power Management tab of the Intel I210 Gigabit Network Connection Properties dialog for
the primary Ethernet port in Device Manager. The NI GigE Vision driver (NI-GEV) does not
support Wake-on-LAN. The PoE Ethernet ports do not support Wake-on-LAN.
Figure 4. Ethernet Port Pin Locations
1
2
3
4
5
6
7
8
Table 2. Ethernet Port Pin Descriptions
Pin Fast Ethernet (100 Mbps) Gigabit Ethernet
MDI MDI-X
1 TX+ BI_DA+ BI_DB+
2 TX- BI_DA- BI_DB-
3 RX+ BI_DB+ BI_DA+
4 No Connect BI_DC+ BI_DD-
5 No Connect BI_DC- BI_DD-
6 RX- BI_DB- BI_DA-
7 No Connect BI_DD+ BI_DC+
8 No Connect BI_DD- BI_DC-
USB 2.0 Ports
The USB ports support common USB peripheral devices such as USB flash drives, USB hard
drives, USB-to-IDE adapters, keyboards, mice, and USB cameras.
(RT only) LabVIEW usually maps USB mass-storage devices to the /U, /V, /W, or /X drive,
starting with the /U drive if it is available. Refer to the LabVIEW Help for more information.
IC-3120 User Manual | © National Instruments | 5
Figure 5. USB 2.0 Pin Locations
4
3
2
1
Table 3. USB 2.0 Port Pin Descriptions
Pin Signal Name Signal Description
1 VBUS Cable Power (+5 VDC)
2 D- USB Data -
3 D+ USB Data +
4 GND Ground for power return
RS-485/422/232 Serial Port
The IC-3120 has a single serial port that can operate in either RS-485/422 mode or RS-232
mode. Set the serial port mode in the BIOS setup utility.
The serial port is a 10-position RJ50 modular jack, which can connect to serial devices, such
as PLCs, scanners, and lighting devices.
NI recommends the following serial cables for the IC-3120.
Cable Part Number
RJ50 10-position modular plug to DB-9 serial cable 182845-01 for 1 meter cable
182845-02 for 2 meter cable
182845-03 for 3 meter cable
Figure 6. RS-485/422/232 Serial Port Pin Locations
3
4
5
6
7
8
9
10
1
2
6| ni.com | IC-3120 User Manual
Table 4. RS-485/422/232 Serial Port Pin Descriptions
Pin RS-485/422 Mode RS-232 Mode
1 No Connect No Connect
2 TXD- Unused
3 TXD+ Unused
4 No Connect No Connect
5 No Connect No Connect
6 RXD- GND
7 RXD+ Unused
8 Unused TXD
9 Unused RXD
10 GND GND
Related Information
Serial Port Configuration Submenu on page 22
VGA Port
Use the VGA port to connect a monitor to the IC-3120. Use any standard 15-pin VGA cable to
access the VGA port. The VGA port has a maximum resolution of 1920 x 1200 at 60 Hz.
Figure 7. VGA Port Pin Locations
5 15
11
6
1
10
Pin Signal Name Signal Description
1 RED Red analog video signal
2 GREEN Green analog video signal
3 BLUE Blue analog video signal
4 RESERVED Reserved
IC-3120 User Manual | © National Instruments | 7
Pin Signal Name Signal Description
5 GND Ground reference
6 RED RETURN Ground reference
7 GREEN RETURN Ground reference
8 BLUE RETURN Ground reference
9 PWR 5 V power for DDC
10 GND Ground return for power
11 NC No connect
12 DDC_D Data signal of serial communication
13 HSYNC Horizontal synchronization signal
14 VSYNC Vertical synchronization signal
15 DDC_C Clock signal of serial communication
Digital I/O
The 44-pin Digital I/O port on the IC-3120 offers 8 isolated inputs, 8 isolated outputs, 2
bidirectional differential inputs (RS-422) or single-ended input lines that can be used with a
quadrature encoder, and 8 bidirectional TTL lines. The Digital I/O port can be connected to
any appropriate shielded device or connector block using a shielded cable.
NI recommends the following digital I/O cables for the IC-3120.
Cable Part Number
44-pin D-sub male to pigtail cable 156083-03 for 3 meter cable
44-pin D-sub male to 44-position D-sub female cable 156084-03 for 3 meter cable
156084-0R5 for 0.5 meter cable
Refer to the following image and table for pin locations and descriptions.
8| ni.com | IC-3120 User Manual
Figure 8. 44-pin Digital I/O Connector Pin Locations
15
30
44
1
16
31
Table 5. Digital I/O Pin Descriptions
Pin Number Signal Description
1 Diff 0+ Bidirectional RS-422 I/O (positive side), or quadrature encoder
phase A+
2 GND Digital ground reference for TTL and differential I/O
3 TTL 0 Bidirectional TTL I/O
4 TTL 1 Bidirectional TTL I/O
5 GND Digital ground reference for TTL and differential I/O
6 TTL 2 Bidirectional TTL I/O
7 TTL 3 Bidirectional TTL I/O
8 GND Digital ground reference for TTL and differential I/O
9 Diff 1+ Bidirectional RS-422 I/O (positive side), or quadrature encoder
phase B+
10 VISO Isolated power voltage reference output
11 CISO Common ground reference for isolated inputs and outputs
12 Iso Out 0 General purpose isolated input
13 Iso Out 1 General purpose isolated input
14 CISO Common ground reference for isolated inputs and outputs
15 Iso Out 4 General purpose isolated output
16 Diff 0- Bidirectional RS-422 I/O (negative side), or quadrature encoder
phase A-
17 GND Digital ground reference for TTL and differential I/O
18 TTL 4 Bidirectional TTL I/O
IC-3120 User Manual | © National Instruments | 9
Altri manuali per IC-3120
1
Indice
Altri manuali National Instruments Controllori
National Instruments
National Instruments CompactRIO cRIO-9072 Manuale utente
National Instruments
National Instruments NI PXIe-8880 Manuale utente
National Instruments
National Instruments GPIB-SCSI-A Manuale utente
National Instruments
National Instruments NI PXI-8840 Manuale utente
National Instruments
National Instruments GPIB-ENET Series Manuale utente
National Instruments
National Instruments PXI-8109 Manuale utente
National Instruments
National Instruments PXIe-8840 Quad-Core Manuale utente
National Instruments
National Instruments PXIe-8861 Manuale utente
National Instruments
National Instruments RMC-8354 Manuale utente
National Instruments
National Instruments CompactRIO cRIO-9066 Manuale utente
National Instruments
National Instruments PCI-8212 Manuale utente
National Instruments
National Instruments NI PXIe-8840 Manuale utente
National Instruments
National Instruments PXI-8106 Manuale utente
National Instruments
National Instruments cRIO-9063 Manuale utente
National Instruments
National Instruments CompactRIO cRIO-9035 Manuale utente
National Instruments
National Instruments IC-3121 Manuale utente
National Instruments
National Instruments NI PXI-6653 Manuale utente
National Instruments
National Instruments VXIpc 600 Series Manuale utente
National Instruments
National Instruments NI cRIO-9036 Manuale utente
National Instruments
National Instruments sbRIO-9605 Manuale utente
