National Instruments NI cDAQ-9134 Manuale del proprietario

SAFETY, ENVIRONMENTAL, AND REGULATORY INFORMATION

NI cDAQ™-9134

NI CompactDAQ Four-Slot Controller

This document includes compliance precautions and connection information for the

NI cDAQ-9134.

Note The guidelines in this document are specific to the NI cDAQ-9134. The other

components in the system might not meet the same ratings. Refer to the

documentation for each component in the system to determine the safety and EMC

guidelines for the entire system.

Safety Guidelines

Caution Do not operate the NI cDAQ-9134 in a manner not specified in this user

manual. Product misuse can result in a hazard. You can compromise the safety

protection built into the product if the product is damaged in any way. If the product

is damaged, return it to National Instruments for repair.

Note Because some C Series modules may have more stringent certification

standards than the NI cDAQ-9134, the combined system may be limited by

individual component restrictions. Refer to the NI cDAQ-9134 Specifications for

more details.

Hot Surface This icon denotes that the component may be hot. Touching this

component may result in bodily injury.

Safety Voltages

Connect only voltages that are below these limits.

V1 terminal to C terminal 30 VDC maximum, Measurement Category I

V2 terminal to C terminal 30 VDC maximum, Measurement Category I

Chassis ground to C terminal 30 VDC maximum, Measurement Category I

Measurement Category I is for measurements performed on circuits not directly connected to

the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is for measurements of voltages

from specially protected secondary circuits. Such voltage measurements include signal levels,

special equipment, limited-energy parts of equipment, circuits powered by regulated low-

voltage sources, and electronics.

Caution Do not connect the cDAQ-9134 to signals or use for measurements within

Measurement Categories II, III, or IV.

Note Measurement Categories CAT I and CAT O are equivalent. These test and

measurement circuits are not intended for direct connection to the MAINS building

installations of Measurement Categories CAT II, CAT III, or CAT IV.

Safety Guidelines for Hazardous Locations

The NI cDAQ-9134 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous

locations; Class I, Zone 2, AEx nA IIC T4 and Ex nA IIC T4 hazardous locations; and

nonhazardous locations only. Follow these guidelines if you are installing the NI cDAQ-9134

in a potentially explosive environment. Not following these guidelines may result in serious

injury or death.

Caution Do not disconnect the power supply wires and connectors from the

controller unless power has been switched off.

Caution Do not disconnect I/O-side wires or connectors unless power has been

switched off or the area is known to be nonhazardous.

Caution Do not remove modules unless power has been switched off or the area is

known to be nonhazardous.

Caution Substitution of components may impair suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications, install the system in an enclosure

rated to at least IP54 as defined by IEC/EN 60079-15.

Caution Do not insert or remove SD cards unless power has been switched off or

the area is known to be nonhazardous.

Caution The USB host ports, USB device port, mini DisplayPort, and SD card slot

require the retention accessories listed in the following table for hazardous locations.

All cables must be used in a conduit or cable gland to wire to a nonhazardous

location. Do not disconnect a cable unless the cDAQ-9134 is powered off or the area

is known to be nonhazardous.

Table 1. Hazardous Location Retention Accessories

Port Required Accessory Part Number

USB Host Port NI Industrial USB Extender Cable 152166-xx

USB Device Port NI Locking USB Cable 157788-01

2| ni.com | NI cDAQ-9134 Safety, Environmental, and Regulatory Information

Table 1. Hazardous Location Retention Accessories (Continued)

Port Required Accessory Part Number

Mini DisplayPort Mini DisplayPort Cable Retention Bracket 156866-01

SD Card Slot SD Door Kit 783660-01

Special Conditions for Hazardous Locations Use in Europe and

Internationally

The cDAQ-9134 has been evaluated as Ex nA IIC T4 Gc equipment under DEMKO

Certificate No. 12 ATEX 1202658X and is IECEx UL 14.0089X certified. Each device is

marked II 3G and is suitable for use in Zone 2 hazardous locations, in ambient temperatures

of -40 °C ≤ Ta ≤ 70 °C.

Caution You must make sure that transient disturbances do not exceed 140% of

the rated voltage.

Caution The system shall only be used in an area of not more than Pollution

Degree 2, as defined in IEC 60664-1.

Caution The system shall be mounted in an ATEX/IECEx-certified enclosure with

a minimum ingress protection rating of at least IP54 as defined in IEC/EN 60079-15.

Caution The enclosure must have a door or cover accessible only by the use of a

tool.

Power Requirements

Caution The protection provided by the NI cDAQ-9134 can be impaired if it is

used in a manner not described in the user documentation.

Note Some C Series modules have additional power requirements. For more

information about C Series module power requirements, refer to the

C Series module(s) documentation.

Note Sleep mode for C Series modules is not supported in the NI cDAQ-9134.

Voltage input range 9 to 30 V (measured at the NI cDAQ-9134

power connector)

Maximum power consumption140 W

Recommended power supply 100 W, 24 VDC

1Includes maximum 1 W module load per slot across rated temperature and product variations.

NI cDAQ-9134 Safety, Environmental, and Regulatory Information | © National Instruments | 3

Note The maximum power consumption specification is based on a fully populated

system running a high-stress application at elevated ambient temperature, and with

all C Series modules and USB devices consuming the maximum allowed power.

Power Connector Characteristics

Screw-terminal wiring

Gauge 0.5 mm 2 to 2.1 mm2 (20 AWG to 14 AWG)

copper conductor wire

Wire strip length 6 mm (0.24 in.) of insulation stripped from the

end

Temperature rating 85 °C

Torque for screw terminals 0.20 N · m to 0.25 N · m (1.8 lb · in. to

2.2 lb · in.)

Wires per screw terminal One wire per screw terminal

Connector securement

Securement type Screw flanges provided

Torque for screw flanges 0.20 N · m to 0.25 N · m (1.8 lb · in. to

2.2 lb · in.)

Wiring Power to the NI cDAQ-9134

The NI cDAQ-9134 requires an external power source as described in the Power Requirements

section. The NI cDAQ-9134 filters and regulates the supplied power and provides power to all

of the I/O modules. The NI cDAQ-9134 has a primary power input, V1, and a secondary

power input, V2. The POWER LED on the front panel identifies the power input in use. When

the LED is lit green, V1 is in use; when the LED is lit yellow, V2 is in use.

Caution Do not connect V2 to a DC MAINS supply or to any supply requiring a

connecting cable longer than 3 m (10 ft). A DC MAINS supply is a local DC

electricity supply network in the infrastructure of a site or building.

Complete the following steps to connect a power source to the NI cDAQ-9134.

1. Make sure the power source is turned off.

2. Install the ferrite (National Instruments part number 711849-01, included in the shipping

kit) across the negative and positive leads of the power source, approximately 50 mm to

75 mm (2 in. to 3 in.) from the ends of the leads near the NI cDAQ-9134.

3. Loosen the connector screw flanges and remove the power screw terminal connector plug

from the NI cDAQ-9134.

Note Do not tighten or loosen the terminal screws on the power connector

while the power is on.

4. Connect the positive lead of the primary power source to the V1 terminal of the power

connector plug and tighten the terminal screw.

4| ni.com | NI cDAQ-9134 Safety, Environmental, and Regulatory Information

5. Connect the negative lead of the primary power source to one of the C terminals of the

power screw terminal connector plug and tighten the terminal screw.

6. Optionally, you can connect the positive lead of a secondary power source to the

V2 terminal and the negative lead to the other C terminal.

7. Install the power connector plug on the front panel of the NI cDAQ-9134 and tighten the

connector screw flanges.

8. Turn on the external power source(s).

The cDAQ controller uses V1 if the voltage across V1 and C is 9 V or greater. If the V1-to-C

voltage drops below 9 V, the NI cDAQ-9134 switches to V2. If the V2-to-C voltage is less

than 9 V, operation may be interrupted.

Note If the NI cDAQ-9134 is using V1 and a secondary power source is connected

to V2, there is a small leakage current on V2. The leakage current depends on the

V2-to-C voltage. Refer to the NI cDAQ-9134 Specifications for nominal values of

this leakage current

If the power source is connected to the power connector using long wiring with high DC

resistance, the voltage at the power connector may be significantly lower than the specified

voltage of the power source.

The C terminals are internally connected to each other but are not connected to chassis ground.

You can connect the C terminals to chassis ground externally. Refer to the Power

Requirements section for information about the power supply input range. Refer to the Safety

Guidelines section for information about the maximum voltage from terminal to chassis

ground.

Caution Removing power without shutting down the NI cDAQ-9134 for Windows

can corrupt the embedded Windows system drive.

Preparing the Environment

Ensure that the environment you are using the NI cDAQ-9134 in meets the following

specifications.

Temperature (IEC 60068-2-1 and IEC 60068-2-2)

Operating -40 to 70 °C

Storage -40 to 85 °C

Caution Failure to follow the mounting instructions in the

NI cDAQ-9132/9133/9134/9135/9136/9137 User Manual can cause temperature

NI cDAQ-9134 Safety, Environmental, and Regulatory Information | © National Instruments | 5

derating. For more information about mounting configurations and temperature

derating, go to ni.com/info and enter Info Code cdaqmounting.

Pollution Degree (IEC 60664) 2

Maximum altitude 5,000 m

Indoor use only.

Note Refer to the NI cDAQ-9134 Specifications for complete specifications.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, product installation requires

either special considerations or user-installed add-on devices. Refer to the

NI cDAQ-9132/9133/9134/9135/9136/9137 User Manual for further information.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories. Note that the input DC power cables may be

unshielded.

Caution To ensure the specified EMC performance, do not connect V2 to a

DC MAINS supply or to any supply requiring a connecting cable longer than 3 m

(10 ft). A DC MAINS supply is a local DC electricity supply network in the

infrastructure of a site or building.

Caution To ensure the specified EMC performance, the length of any cable

connected to the video and USB host ports must be no longer than 3 m (10 ft). The

length of any cable connected to the RS-232 port must be no longer than 30 m

(100 ft).

Caution The USB device port is intended for use in device configuration,

application deployment, debug, and maintenance.

6| ni.com | NI cDAQ-9134 Safety, Environmental, and Regulatory Information

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for marine (shipboard) applications.

To verify Lloyd’s Register certification for a product, visit ni.com/certification and search for

the LR certificate, or look for the Lloyd’s Register mark on the product.

Caution In order to meet the EMC requirements for marine applications, install the

product in a shielded enclosure with shielded and/or filtered power and input/output

ports. In addition, take precautions when designing, selecting, and installing

measurement probes and cables to ensure that the desired EMC performance is

attained.

Connecting to the cDAQ Controller

Connecting to the Network through the Ethernet Port

Caution To prevent data loss and to maintain the integrity of your Ethernet

installation, do not use a cable longer than 100 m.

Connecting to the Mini DisplayPort Connector

Caution Do not hot-swap mini DisplayPort devices while the NI cDAQ-9134 is in

a hazardous location or connected to high voltages.

Connecting to the USB Host Ports

Install a noise-suppression ferrite (National Instruments part number 711849-01, included in

the shipping kit) around all external USB cables attached to the USB host ports to ensure that

your device meets all EMC standards applicable to your country. The ferrite should be

installed so that it is approximately 50 to 75 mm (2 to 3 in.) from the end of the cable that

plugs into the USB host port. The ferrite should accommodate both USB cables depending on

cable diameter.

Caution Do not hot-swap USB devices while the NI cDAQ-9134 is in a hazardous

location or connected to high voltages. If the NI cDAQ-9134 is not in a hazardous

location, you can connect and disconnect USB devices without affecting operation.

Connecting to the USB Device Port

Caution National Instruments requires a locking USB cable, such as part number

157788-01, in order to meet the shock and vibration specifications of this product.

Caution Do not hot-swap USB devices while the NI cDAQ-9134 is in a hazardous

location or connected to high voltages. If the NI cDAQ-9134 is not in a hazardous

location, you can connect and disconnect USB devices without affecting operation.

NI cDAQ-9134 Safety, Environmental, and Regulatory Information | © National Instruments | 7

Connecting to the NI-XNET CAN/LIN Connector

Caution To maintain product performance and accuracy specifications when using

the NI-XNET CAN/LIN port and NI transceiver cable(s), do not attach or mount the

transceiver overmold directly to the NI cDAQ-9134. Mount the overmolded section

of the transceiver cable at least 50.8 mm (2.00 in.) away from the NI cDAQ-9134.

Caution Do not hot-swap NI-XNET devices while the NI cDAQ-9134 is in a

hazardous location or connected to high voltages. If the NI cDAQ-9134 is not in a

hazardous location, you can connect and disconnect NI-XNET devices without

affecting operation.

Using the SD Card Removable Storage

Caution You must use the SD card slot cover to protect the SD card in hazardous

locations.

Caution Do not insert or remove SD cards unless power has been switched off or

the area is known to be nonhazardous.

Where to Go Next

The following documents contain information that you may find helpful as you use this

document:

•NI cDAQ-9132/9133/9134/9135/9136/9137 User Manual

•NI cDAQ-9134 Specifications

Worldwide Support and Services

NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,

78759-3504. NI also has offices located around the world. For telephone support in the United

States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For

telephone support outside the United States, visit the Worldwide Offices section of ni.com/

niglobal to access the branch office websites, which provide up-to-date contact information,

support phone numbers, email addresses, and current events.

Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on NI trademarks. Other product and

company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI

products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the

National Instruments Patent Notice at ni.com/patents. You can find information about end-user license agreements (EULAs)

and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/

legal/export-compliance for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other

import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION

CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in

this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth

in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

371802B-02 Nov15

Indice

Altri manuali National Instruments Controllori

National Instruments

National Instruments cDAQ-9139 Manuale utente

National Instruments

National Instruments PXI-8109 Manuale utente

National Instruments

National Instruments 73 Series Manuale utente

National Instruments

National Instruments NI cRIO-9035 Manuale utente

National Instruments

National Instruments sbRIO-9637 Manuale utente

National Instruments

National Instruments NI PXIe-8840 Manuale utente

National Instruments

National Instruments NI 7340 Manuale utente

National Instruments

National Instruments PXI-665 Series Manuale utente

National Instruments

National Instruments SB-GPIB Manuale utente

National Instruments

National Instruments cRIO-9034 Manuale utente

National Instruments

National Instruments PXI-7344 Manuale utente

National Instruments

National Instruments sbRIO-9637 Manuale utente

National Instruments

National Instruments sbRIO-9860 Manuale utente

National Instruments

National Instruments GPIB-1284CT Manuale utente

National Instruments

National Instruments SCXI USB-1357 Manuale utente

National Instruments

National Instruments GPIB-232 Manuale utente

National Instruments

National Instruments GPIB Series Manuale utente

National Instruments

National Instruments UMI-7774 Manuale utente

National Instruments

National Instruments Compact FieldPoint cFP-21 Series Manuale utente

National Instruments

National Instruments CompactRIO cRIO-9035 Manuale utente

National Instruments

National Instruments PXI-8232 Manuale utente

National Instruments

National Instruments RMC-8354 Manuale utente

National Instruments

National Instruments CompactRIO cRIO-9002 Manuale utente

National Instruments

National Instruments PXIe-8820 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente