National Instruments PXI-8109 Manuale utente

INSTALLATION GUIDE

NI PXI-8109 and NI PXIe-8133

Flex Cable Replacement

This guide describes how to install the flex cable replacement for the

NI PXI-8109 and NI PXIe-8133 embedded controllers. For more detail and

a video demonstration of the cable replacement, please visit ni.com/info

and enter the Info Code 8133FlexReplace.

The flex cable can be replaced by hand. No tools are needed and the

controller does not need to be disassembled. Perform the following steps

for installation and removal instructions.

1. Locate the single-ended board to board flex cable on your

NI PXI-8109 or NI PXIe-8133 embedded controller as shown below in

Figure 1.

Figure 1. View of the Controller Back End with Board to Board Flex Cable

Caution Touch the metal part of the case to discharge any static electricity that might be

on your clothes or body.

1 Board to Board Flex Cable

LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle

logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at

ni.com/trademarks for other National Instruments trademarks. Other product and company

names mentioned herein are trademarks or trade names of their respective companies. For patents

covering National Instruments products/technology, refer to the appropriate location: Help»Patents

in your software, the patents.txt file on your media, or the National Instruments Patent Notice

at ni.com/patents. Refer to the Export Compliance Information at ni.com/legal/

export-compliance for the National Instruments global trade compliance policy and how to

obtain relevant HTS codes, ECCNs, and other import/export data.

*325798A-01*

2. Remove the existing cable by completing steps a and b below.

Caution Do not put pressure on additional components near the connector or scrape the

connector against components while removing the cable.

a. Gently remove by hand (no tools necessary) both sides of the

cable from the mating connectors on the two boards of the

controller.

1. Disconnect one side of the flex cable from its mating

connector.

2. Straighten the cable after disconnecting the first side.

3. Disconnect the second side of the flex cable from its mating

connector.

b. Discard the old cable.

3. Install the new cable.

a. The replacement cable will be flattened when it arrives.

b. Each connector is keyed in a way to prevent improper installation.

c. Connect one side of the new flex cable to the appropriate keyed

connector on the controller.

d. Slowly bend the cable using large angles such that the second flex

cable connector is above the mating connector on the controller,

and make the connection.

Caution Tight bends or creases in the cable will damage its functionality.

e. Once both sides of the cable are in place apply moderate pressure

on both sides to ensure a good connection. Do not push on other

components in the process. You may need to gently push the

middle of the cable toward the inside of the controller to square up

the connectors on the board.

4. Verify the cable is installed correctly.

a. Install the controller into a chassis.

b. Power on the chassis.

c. Verify the controller boots properly.

Altri manuali per PXI-8109

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali National Instruments Controllori

National Instruments

National Instruments GPIB-110 Manuale utente

National Instruments

National Instruments Compact FieldPoint cFP-21 Series Manuale utente

National Instruments

National Instruments SCXI USB-1357 Manuale utente

National Instruments

National Instruments GPIB-1284CT Manuale utente

National Instruments

National Instruments PXIe-8115 Manuale utente

National Instruments

National Instruments NI SMD-7613 Manuale utente

National Instruments

National Instruments NI-488.2M Manuale utente

National Instruments

National Instruments NI 7340 Manuale utente

National Instruments

National Instruments NI PXIe-8135 Manuale utente

National Instruments

National Instruments CompactRIO cRIO-9035 Manuale utente

National Instruments

National Instruments PXI-8195 Manuale utente

National Instruments

National Instruments cRIO-9023 Manuale utente

National Instruments

National Instruments Fieldpoint CFP-2200 Manuale utente

National Instruments

National Instruments PXIe-8861 Manuale utente

National Instruments

National Instruments GPIB-232 Manuale utente

National Instruments

National Instruments PXI-8150B Guida rapida

National Instruments

National Instruments PXI-8119 Manuale utente

National Instruments

National Instruments IC-3171 Manuale utente

National Instruments

National Instruments GPIB-ENET Manuale utente

National Instruments

National Instruments cDAQ-9139 Manuale utente

National Instruments

National Instruments NI 8352 Manuale utente

National Instruments

National Instruments NI cRIO-9035 Manuale utente

National Instruments

National Instruments PXI-8150B Manuale utente

National Instruments

National Instruments cRIO-9037 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente