Nds surgical imaging Dome Ex Manuale utente
© 2011 NDS Surgical Imaging. All rights reserved.
Information in this document has been carefully checked for accuracy; however, no
guarantee is given to the correctness of the contents. This document is subject to
change without notice. NDSsi provides this information as reference only. Reference
to products from other vendors does not imply any recommendation or
endorsement.
This document contains proprietary information protected by copyright. No part of
this manual may be reproduced by any mechanical, electronic, or other means, in
any form, without prior written permission of NDSsi.
NDS Surgical Imaging, NDSsi, the NDSsi logo, Dome, the Dome by NDSsi logo,
Dome E2, Dome E2cHB, Dome E3, Dome E3cHB, Dome E3cHB DisplayPort, Dome E5,
Dome CXtra, RightLight are either registered or unregistered trademarks of NDS
Surgical Imaging. All other trademarks are the property of their respective owners.
020-0902-00A
About the Display
The Dome® Ex display systems, ranging from 2 to 5 megapixels,
consists of a TFT LCD panel and a display board and driver. The
display’s thin film transistors, in a transmissive-type display, use an
integrated cold cathode fluorescent tube (CCFT) backlight system.
The display is designed for medical imaging in diagnostic settings, in
portrait or landscape orientation, and comes fully tuned with gamma
correction that complies with the DICOM Part 14 Standard. The all-
digital design enables the display to produce the sharp, crisp images
critical to softcopy medical viewing. Unwanted analog display image
artifacts are eliminated.
Bundled with the display system, the Dome CXtra software enhances
the functionality of the Dome Ex display with a range of value-added
services, such as DICOM calibration, error reporting, and backlight
saver. Network management of Dome displays running the Dome
CXtra software requires the Enterprise Management Service for
Dome CXtra. For more information, refer to Dome CXtra User’s Guide.
2 | Dome Ex Display
* Some Dome Ex displays ship with a DC adapter that operates per power switch.
** For Dome E3cHB DisplayPort unit only.
AMLCD panel mounted on desk stand
Display controller DC power adapter* Power cords
DVI cable DisplayPort cable**
Display driver and
calibration software
About the Display | 3
System Requirements
All display systems require operating system Windows 7 (x86 or x64)
or Windows XP Service Pack 3 (x86 or x64).
IMPORTANT! Note the following:
• NVIDIA boards. Display configurations using the NVS295 board
require a DisplayPort-to-DVI adapter. Display configurations, except
for the Dome E3cHB DisplayPort unit, using Quadro 600, Quadro 2000,
or Quadro 4000 require a DisplayPort-to-DVI adapter for the second
display.
• Ten-bit display systems. Graphics boards cannot be mixed on 10-bit
display systems. Use multiple boards of the same type.
Display Controller System Requirements
Dome E2
Dome E2cHB
NVS295*
* NVS295 board x1 or x16.
• Intel or AMD multi-core
processor
• PCI Express x16 lane slot
• 50 MB hard disk space
• 512 MB RAM
•CD-ROMdrive
• Power supply, 350 watts or
greater
• Auxiliary power cable with
standard 6-pin connector
(for Quadro 4000 only)
Dome E2
Dome E2cHB
Dome E3
Dome E3cHB
Dome E3cHB DisplayPort
Dome E4c†
Dome E5
†RefertoDome E4c Display User’s Guide for instructions.
Quadro FX380 or
Quadro 2000D
Dome E2
Dome E2cHB
Dome E3
Dome E3cHB DisplayPort
Dome E5
Quadro 600,
Quadro 2000, or
Quadro 4000
4 | Dome Ex Display
Display Components
Review this illustration of the back panel to identify controls and
ports on the display unit. Also see “Connector Ports” on page 31.
All Dome Ex displays include the following on the connector plate:
• Power input. Drives power to the display; 4-pin port on Dome E2,
8-pin port on Dome E2cHB, Dome E3, and Dome E5, either 6- or
8-pin port on Dome E3cHB, and 6-pin port on Dome E3cHB
DisplayPort.
• Video input. Drives the data to the display. All Dome Ex displays
have a standard DVI connector. The Dome E3cHB DisplayPort
unit also includes a DisplayPort connector port.
• Reset button. Restores the display configuration to default
setting.
• LED lights. Provides information on the status of the display.
NOTE: Usage of both the mini-B USB port on Dome E3cHB and the
USB-B port on Dome E3cHB DisplayPort to be defined at a future
time.
Dome E2, Dome E2cHB,
Dome E3cHB
Dome E3, and Dome E5
Dome E3cHB DisplayPort
Installing the Display | 5
Installing the Display
Before you install the display controller, remove any graphics card and its driver from
your system. Also disable any onboard graphics capability on the motherboard.
Install your Dome display with one of the qualified graphics cards shown in the
following table. See the I/O bracket of the graphics card on “Qualified Graphics Cards”
on page 32.
NVS QUADRO
DISPLAY 295*
* DisplayPort-to-DVI adapter required.
FX 380 600†
† DisplayPort-to-DVI adapter required for second Dome Ex display, except Dome E3cHB DisplayPort.
2000†2000D 4000†
Dome E2 999999
Dome E2cHB 999999
Dome E3 99999
Dome E3cHB 99
Dome E3cHB
DisplayPort 99999
Dome E4c‡
‡ Refer to Dome E4c Display User’s Guide for instructions.
99
Dome E5 99999
Warning
In locations where 240V outlets are used, connect the Dome Ex display only to a
center-tapped, 240V, single-phase supply (for Canada and the United States only).
If you leave the computer turned on, you could get an electric shock and cause damage to
the system components.
Remove the display controller slowly from its package and static-shielding bag to prevent
an electrostatic discharge.
Static electricity can damage the controller. When touching the board or parts of the
motherboard, take these precautions:
• Wear an antistatic wrist strap.
• Discharge your body’s static electricity repeatedly by touching the power supply or the
metal surface of the computer chassis.
6 | Dome Ex Display
Installing the Display Controller
Before you install the display controller, choose a well-ventilated
location with an adequate amount of space. Excessive heat cannot
dissipate when display vents are blocked. Make sure a grounded AC
outlet is within easy reach.
Turn your computer off. Leave the power cord plugged into the
grounded outlet.
To install the display controller
1 Remove the computer cover.
2 Remove any existing graphics card and video signal cable.
3 Remove the blank bracket from an available PCI Express slot.
4 Insert the display controller into the slot, align the connector pins,
and press the board down until it is firmly seated.
5 For Quadro 4000 board only: Connect the 6-pin auxiliary power
supply cable to the controller. (Use the built-in 6-pin connector if it
is present.)
6 Secure the mounting bracket.
7 Reattach the computer cover and the peripherals.
Hardware Installation Tips
• NVIDIA boards. All boards referred to in this manual, except the
NVS295 board, support single link and dual link on DVI ports. The
NVS295 board supports single link only via DisplayPort-to-DVI
adapter.
• Multiple displays. Connect all displays to the video board before
you turn on the computer and install the driver.
• Access to ports. For displays mounted on a desk stand, rotate the
LCD panel from portrait to landscape for better access to the
ports.
• Threading cables. Thread the DVI cable and power cord through
the stand column. Make sure the cable and cord run through the
notches. To reattach the stand cover, align the hooks with the
slots on the stand. Press the cover into place. A click sound signals
a secure connection.
Installing the Display | 7
NOTE: For installation of the Quadro 4000 board only. If your
computer lacks a built-in 6-pin connector from the power supply, you
need to use the adapter cable supplied with the display controller to
complete the installation of the board.
Connecting the Video and Power Cables
Turn your computer off. Leave the power cord plugged into
the grounded outlet. Use the Dome Ex display with the power
adapter and video cable shipped.
IMPORTANT! Note the following:
• Display configurations using the NVS295 board may require a
DisplayPort-to-DVI adapter.
• Display configurations using the Quadro 600, 2000, or 4000 board,
except for the Dome E3cHB DisplayPort unit,require a DisplayPort-
to-DVI adapter for the second display.
•FortheDomeE3cHBDisplayPort unit only. Install either the DVI or
the DisplayPort video cable, not both.
To connect the cables
1 Plug one end of the video cable into the video port on the interface
plate. Secure the connection.
2 Plug the power cord into the power input port on the
interface plate.
3 Plug the other end of the video cable into the video port on the
installed display controller. (Use the bottom port of a single display
installation or for the first display of a multiple display setup.)
Secure the connection.
4 Plug the other end of the power cord into the power supply.
5 Repeat steps 1 to 4 to connect another display to the controller.
6 Plug the power supply cord(s) into a grounded AC outlet.
7 If you are using a BridgePower adapter, turn on the adapter power
switch before you turn on the computer.
8 | Dome Ex Display
Installing the Display Driver
Before you install the driver, remove any previously installed display
driver for the display controller from your system.
To install the driver
1 Start the system.
Note: On Windows XP, click Cancel on the Found New Hardware
Wizard.
2 Insert the driver installation CD and run Setup.exe.
3ClickNext.
4 Click Yes to the license agreement. The installation starts.
5 Follow the onscreen instructions to complete the installation. When
the Setup complete message appears, select Yes, I want to restart
my computer now. Click Finish.
6 If the Digital Signature Not Found message appears, click Yes or
Continue to complete the driver installation.
Indice
Altri manuali Nds surgical imaging Monitor
Nds surgical imaging
Nds surgical imaging Dome E2c Manuale utente
Nds surgical imaging
Nds surgical imaging Radiance Series Manuale utente
Nds surgical imaging
Nds surgical imaging Dome GX2MP Plus Manuale utente
Nds surgical imaging
Nds surgical imaging Dome E2 Manuale utente
Nds surgical imaging
Nds surgical imaging Dome GX2MP Manuale utente
