NEC MultiSync LCD1700M+ Manuale utente
English
1700e.p65 01/02/28, 17:40Page 9 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
1700e.p65 01/02/28, 17:40Page 10 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
Contents
Your new NEC MultiSync monitor box* should contain the following:
– MultiSync LCD1700M+ Monitor.
– Power Cords.
– Audio Cable.
– User’s Manual.
– Installation Disk.**
* Remember to save your original box and packing material to transport
or ship the monitor.
** This diskette contains the Windows 95/98 INF file. This enables easy
and correct configuration of the monitor witn this operating system.
To use the INF file, double-click on the display icon in the control
panel, select the settings tab and follow the instructions to change the
monitor type.
Contents E - 1
MultiSync LCD1700M+ Monitor
Power Cords
Audio Cable
1700e.p65 01/02/28, 17:40Page 11 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
Hardware Installation
To attach the MultiSync monitor to your system, follow these instruc-
tions:
1. Make sure that the computer and monitor’s power are both turned
off. Please follow the steps to install your LCD monitor.
a. Place monitor face down on a non-abrasive surface. Take off
the rear cover, then the base cover.
b. Connect the power cord to your LCD monitor. Then connect
the audio cable into the Audio Input of the monitor. Reattach
base cover.
c. Put rear cover back.
d. Plug the 15-pin Mini D-SUB cable into the signal connector
of the computer.
E - 2 Hardware Installation
Bundle cables here.
1700e.p65 01/02/28, 17:40Page 12 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
2. Connect the power cord at the back of the monitor to an AC
power socket.
Please make sure, that the socket is not blocked or covered, so
you can disconnect the unit from AC supply if you need to. Your
monitor is equipped with an automatic power supply for a volt-
age range from 100 to 240 Volt at a frequency of 50 to 60 Hz.
Be sure that your local power is within the supported range. If
you are unsure, ask your electricity supplier.
Hardware Installation E - 3
1700e.p65 01/02/28, 17:40Page 13 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
E - 4 Software Installation
Software Installation
Choosing the best resolution
Due to the technology of a LCD monitor, it always provides a fixed reso-
lution. For this monitor, it is a resolution of 1280x1024. This is called the
native resolution, which also represents the maximum resolution. Lower
resolutions are displayed on a full screen through an interpolation circuit.
Flaws do occur with the interpolated resolution compared to the native
resolution. If you want to have all the advantages of LCD technology you
must use the native resolution. Using Windows 95/98/2000 you can change
the resolution as follows:
1. Double-click the “Display”icon in the control panel.
2. From the “Display properties”window, select the “Settings”tab.
There is a slider on the right-hand side in the middle of the win-
dow. There you can alter the resolution.
3. Set a resolution of 1280x1024.
4. In the subsequent window press: “Apply”, “OK”and “Yes”.
5. You can now close “Display Properties”.
Refresh Rate Selection
There is no need to choose the highest possible refresh rate on a LCD
monitor. It is not technically possible for a LCD display to flicker. Even
at a refresh rate of 60 Hz you will get an absolutely flicker-free image.
More important is that you make sure that you use one of the factory
modes. In contrast to a modern CRT monitor, which is a multi-scan moni-
tor, this model is a multi-frequency monitor. This means, the best results
are only obtained by using the factory modes. You will find a table with
the factory modes in this user guide. For the native resolution of
1280x1024, these, for example, are 60, 70 and 75 Hz, not 72 Hz. In Win-
dows 95/98/2000 you can change the refresh rate as follows:
1. Double click the “Display”icon in the control panel.
2. From the “Display properties”window, select the “Settings”tab.
Click the “Advanced properties”button in the bottom right cor-
ner.
1700e.p65 01/02/28, 17:40Page 14 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
3. Select the “Adapter”tab. The refresh rate selection field is lo-
cated in the center at the bottom of the window.
4. Choose a refresh rate from the table with the factory modes,
which can be found in the user’s guide, and select this in the
settings field.
5. In the subsequent window press: “Apply”, “OK”and “Yes”.
6. You can now close “Display Properties”.
Software Installation E - 5
1700e.p65 01/02/28, 17:40Page 15 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
E - 6 Adjusting the Monitor
Adjusting the Monitor
There are 4 keys & one wheel for user’s control that includes Power,
Auto, Exit, Enter and a wheel. The following descriptions are the intro-
duction of these keys & fly wheel.
1. Power: Turn the power on or off.
2. Auto: Adjust vertical position, phase, horizontal position and
pixel clock automatically.
3. Exit: Back to main menus ; Entering “save menu”; Exit OSD
menu without saving. Hot key for Audio volume adjustment.
4. Enter: Enter main/sub menus ; select items ; save menu.
5. Fly-wheel: Left/right adjustment. Hot key for Brightness/Con-
trast adjustment.
Power Indicator
Power
Auto
Fly-wheel
Exit Enter
1700e.p65 01/02/28, 17:40Page 16 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
Adjusting the Monitor E - 7
Adjustable Items
Luminance
Contrast
Adjusts the contrast.
Brightness
Adjusts the brightness.
Geometry
Hor. Position
Adjusts a displaying position in horizontal direction.
Ver. Position
Adjusts a displaying position in vertical direction.
Phase
Adjusts a phase when horizontal noise is displayed on the
screen. Also used when characters are blurred or not sharply
displayed.
Pixel Clock
Expands or contracts the screen.
Color Adjustment
(9300K)
Selects the pre-set colour (9300K).
(6500K)
Selects the pre-set colour (6500K).
(5800K)
Selects the pre-set colour (5800K).
(User)
Adjusts the colour proportion for red, green and blue.
1700e.p65 01/02/28, 17:40Page 17 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
E - 8 Adjusting the Monitor
Recall (Display Mode)
Displays information about the input signal.
Returns a currently displayed set value for signal to factory
set one when Enter key is pressed.
(Only values adjusted at Geometry can be returned to fac-
tory set ones.)
Miscellaneous
OSD Position
Adjusts an OSD menu position.
Language Select
Switches the current language displayed on OSD menu into
another.
OSD Time
Set a time in which OSD menu disappears automatically.
Zoom
Selects whether or not display is expanded to 1280 x 1024.
Volume
Adjusts the speaker volume.
SN (Serial Number)
Displays the serial number of this liquid crystal display
(LCD).
1700e.p65 01/02/28, 17:40Page 18 AdobePageMaker6.5J/Win
ﾌﾞﾗｯｸ
Altri manuali per MultiSync LCD1700M+
1
Indice
Altri manuali NEC Monitor
NEC
NEC MultiSync 75F Manuale utente
NEC
NEC NEC MultiSync LCD1525V LCD1525V LCD1525V Manuale utente
NEC
NEC MultiSync LCD6520 Manuale utente
NEC
NEC MULTEOS M461 Manuale utente
NEC
NEC SpectraView LCD2180 WideGamut LED Manuale utente
NEC
NEC LCD2335WXM - MultiSync - 23" LCD TV Guida
NEC
NEC MultiSync C431 Manuale utente
NEC
NEC PlasmaSync 42XR4 Manuale utente
NEC
NEC EA273WM-BK Manuale utente
NEC
NEC MD304MC - MultiSync - 29.8" LCD Monitor Manuale del prodotto
NEC
NEC LCD1810 - MultiSync - 18.1" LCD Monitor Manuale utente
NEC
NEC MultiSync X462S Manuale utente
NEC
NEC MultiSync LCD1510 Manuale utente
NEC
NEC MultiSync EA231WMi Manuale utente
NEC
NEC MultiSync FP1375X Manuale utente
NEC
NEC MultiSync P241W Manuale elenco delle parti
NEC
NEC MultiSync V651 Manuale utente
NEC
NEC LCD1980SX - MultiSync - 19" LCD Monitor Manuale utente
NEC
NEC MultiSync L234GC Manuale utente
NEC
NEC NEC MultiSync FE950+ FE950+ FE950+ Manuale utente
