NEC NP3150CM Guida

Questo manuale è adatto per i seguenti modelli

10

Indice

Altri manuali NEC Rack e supporto

NEC

NEC Wall Mount WMS32-55 Manuale utente

NEC

NEC WM-46UN Wall Mount Portrait and Landscape Manuale utente

NEC

NEC NP-M260W Guida

NEC

NEC N8154-46 Manuale utente

NEC

NEC Video Wall Mount PD02VW MFS 46 55 L Guida

NEC

NEC Wall Mount PDW S 32-55 P (WMS 32-55 P Manuale utente

NEC

NEC MultiSync P701 Manuale utente

NEC

NEC T1000 - STAND MOUNTING Manuale utente

NEC

NEC N8143-93 Manuale utente

NEC

NEC LT30 - XGA DLP Projector Guida

NEC

NEC NP04WK Manuale utente

NEC

NEC N8120-102 Manuale utente

NEC

NEC NEC ST-EX2023 Manuale utente

NEC

NEC LCD3215 - MultiSync - 32" LCD Flat Panel... Manuale utente

NEC

NEC NP-UM330W Series Manuale utente

NEC

NEC WMK-3298T Manuale utente

NEC

NEC NEC W32-70 Manuale utente

NEC

NEC easyHook NEC55 Manuale utente

NEC

NEC WMK-3257 Guida

NEC

NEC PlasmaSync PX-60XM5A Manuale utente

NEC

NEC WM-46S-P Manuale utente

NEC

NEC ST-EX2023-BK Manuale utente

NEC

NEC NP40CM Guida

NEC

NEC NP05WK1 Guida

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente

5880 Sheridan Boulevard, Arvada, Colorado 80003

Ph: 303-412-0399 ▪Fax: 303-412-9346

www.displaydevices.com



NECDisplaySolutionsofAmerica,Inc.



InstallationandAssemblyManual:

CustomCeilingMountforNECNP1000,NP2000,NP1150,NP2150,

NP3150,NP3151W,NP1250,NP2250,NP3250,andNP3250WProjectors



Model:NP3150CM

Ceiling Mount

1. Remove ¼”-20 button head bolt on ceiling plate to remove lower portion of mount.

2. Install the ceiling plate with (4) 5/16” bolts to structural attachment points. Lag screws

may be used when attaching to wood joists.

3. Reattach the lower portion of the mount.

4. Attach interface plate (pn 72-061) to projector with (4) M4 x 10 pan head Phillips screws.

5. Align interface plate into holes on mount, slide stand off bolts into slots and tighten. Add

center locking Torx cap screw which attach secures the interface plate to the mount.

6. Attach the wire safety rope to the interface plate with the enclosed coupler.

7. Attach power and signal cables to projector.

8. Attach the I/O cover (pn 72-065) to the interface plate with (4) 10-32 x 3/8 pan head

Phillips screws and #10 lock washers.

9. Loosen tilt adjustment cap screw with enclosed tool and level the projected image to the

screen. Tighten cap screw when a level image is achieved.

10. Loosen up-down pitch adjustment cap screw with enclosed tool and adjust the pitch

angle of the projector. Tighten cap screw when at desired projection position.

11. If desired, add Kensington lock through the opening of the mount head, loop through

cable end and attach to projector.

5880 Sheridan Boulevard, Arvada, Colorado 80003

Ph: 303-412-0399 ▪Fax: 303-412-9346

www.displaydevices.com

Pole Mount

1. Install a 1 ½” NPT pipe with male threads on lower end from the ceiling. Aftermarket

mounting pans and accessories are available.

2. Thread locking ring onto pipe. Thread mount onto pipe and leave locking ring loose.

3. Attach interface plate (pn 72-061) to projector with (4) M4 x 10 pan head Phillips screws.

4. Align interface plate into holes on mount, slide stand off bolts into slot and tighten. Add

center locking Torx cap screw which attach secures the interface plate to the mount.

5. Attach the wire safety rope to the interface plate with the enclosed coupler.

6. Insert power and signal cables through pipe and out the top of the mount head to the

projector and attach to projector.

7. Attach the I/O cover (pn 72-065) to the interface plate with (4) 10-32 x 3/8 pan head

Phillips screws and #10 lock washers.

8. Adjust left-to-right yaw. When desired position is attained, tighten locking ring on pipe

to mount.

9. Loosen tilt adjustment cap screw with enclosed tool and level the projected image to the

screen. Tighten cap screw when a level image is achieved.

10. Loosen up-down pitch adjustment cap screw with enclosed tool and adjust the pitch

angle of the projector. Tighten cap screw when at desired projection position.

11. If desired, add Kensington lock through the opening of the mount head, loop through

cable end and attach to projector.