Necta Kobalto Manuale del proprietario
PROGRAMMING MANUAL
Code: Date:P285U00
English
05 - 2007
P285U00 05 - 2007
IntroductIon
This “Programming Manual” is a very useful tool for those operators who want to get the most out of the
potential of the installed software and know in detail all of the software available functions.
This document is available in PDF format in the Reserved Area of our internet site
www.nwglobalvending.com or, on request, through our after-sales service.
The Manual is divided into 2 parts:
The First Part contains the information concerning the Filler Menu.
The Second Part contains the information concerning the Technician Menu.
The operations described can modify the functioning cycles, therefore they must be carried out only by per-
sonnel who have the specic knowledge of the machine functioning from a point of view of electrical safety
and health regulations.
IntroductIon
The machines can function in 3 different operating modes:
- Normal Vending
- Filler Menu
- Technician Menu
normal vendIng mode
In Normal Vending mode it is possible to perform some operations with the door closed, keeping pressed the
wash button “” for more than 2 seconds or the “ ” button (see gure) if the wash button is not present.
The push-buttons take on numeric values as shown in the gure:
The machine waits a few seconds for the entry of a 5-digit
code that will allow the following operations if enabled in the
Password option within the Technician Menu:
- Reset counters
- Jug Facility
- Free Vending
- Keypad lock
- Wash
- Test selections
- Filter reset
- Waste tray reset
By default all passwords are disabled.
A
P285U00 05 - 2007
programmIng menu
In order to access the programming menu, open the front door of the vending machine, switch on the ma-
chine and insert the yellow key supplied in the relevant slot located on the left-hand side of the machine.
1
Press the programming access button as shown in the gure:
The machine goes into “Filler Menu” mode.
The buttons shown in the gure are used for surng through the different menus:
Scrolling buttons UP “” and DOWN “”
The UP and DOWN scrolling buttons are used for moving from one programming menu item to the next one,
located in the same level, and at the same time change the status or the numeric value of the corresponding
functions.
Conrm / enter button “”
The conrm / enter button is used for moving to the lower level or for conrming a value after being entered
or changed.
Exit button “”
The exit button is used for returning to the higher level or for exiting a change eld of a function. When reach-
ing the highest level in the menu, this button is pressed for going from the Technician menu into the Filler
menu and vice versa.
B
P285U00 05 - 2007
FILLER MENU
1
1 - STATISTICS
1.1 - STATIS. PRINTING
1.1.1 - PARTIAl PRINTING
1.1.1.1 - SEl. CNT. PRINT.
1.1.1.2 - PRINT BAND CNT
1.1.1.3 - DISC. CNT.PRINT.
1.1.1.4 - FAIl. CNT.PRINT.
1.1.1.5 - COIN MECH. PRINT
1
StatIStIcS
1.1
prIntIng the StatIStIcS
1.1.1
partIal prIntout
1.1.1.1
prIntIng the SelectIon counterS
When conrming this function, the counters regarding the different
selections are printed.
1.1.1.2
prIntIng the tIme band counterS
When conrming this function, the counters regarding the different
time bands are printed.
1.1.1.3
prIntIng the dIScount counterS
When conrming this function, the counters regarding discounts
and overprice are printed.
1.1.1.4
prIntIng the faIlure counterS
When conrming this function, the counters regarding the different
failure are printed.
1.1.1.5
prIntIng the coIn mechanISm data
When conrming this function, the counters regarding the coin
mechanism data are printed.
P285U00 05 - 2007
FILLER MENU
2
1.1.2 - TOTAl PRINTING
1.2 - PRINT REl. STAT.
1.2.1 - PARTIAl PRINTING
1.2.1.1 - SEl. CNT. PRINT.
1.2.1.2 - PRINT BAND CNT
1.2.1.3 - DISC. CNT.PRINT.
1.2.1.4 - FAIl. CNT.PRINT.
1.2.1.5 - COIN MECH. PRINT
1.1.2
total prIntout
When conrming this function, all statistics are printed.
1.2
prIntIng the relatIve StatIStIcS
1.2.1
partIal prIntout
1.2.1.1
prIntIng the SelectIon counterS
When conrming this function, the relative counters regarding the
different selections are printed.
1.2.1.2
prIntIng the tIme band counterS
When conrming this function, the relative counters regarding the
different time bands are printed.
1.2.1.3
prIntIng the dIScount counterS
When conrming this function, the relative counters regarding dis-
counts and overprice are printed.
1.2.1.4
prIntIng the faIlure counterS
When conrming this function, the relative counters regarding
failures are printed.
1.2.1.5
prIntIng the coIn mechanISm data
When conrming this function, the relative counters regarding the
coin mechanism data are printed.
P285U00 05 - 2007
FILLER MENU
3
1.2.2 - TOTAl PRINTING
1.3 - STATIST. DISPlAY
1.3.1 - SEl. CNT. DISP.
1.3.1.1 - CNT DIS. X S.SEl
1.3.1.2 - TOT CNT DISPlAY
1.3.1.3 - SEl.NO.CNT. DIS.
1.3.2 - DISPlAY BAND CNT
1.3.3 - DISC. CNT. DISP.
1.2.2
total prIntout
When conrming this function, all relative statistics are printed.
1.3
dISplayIng the StatIStIcS
1.3.1
dISplayIng the SelectIon counterS
1.3.1.1
dISplayIng the SIngle counterS
This function is used for displaying the counters regarding each
selection, divided by price band (0, 1, 2, 3, 4, Free, Test).
1.3.1.2
dISplayIng the total counterS
This function is used for displaying the total counters regarding
each selection.
1.3.1.3
dISplayIng the SelectIon counterS In normal vendIng - /maIntenance
This function is used for displaying the total counters regarding the
selections made while in normal vending mode and maintenance
mode.
1.3.2
dISplayIng the tIme band counterS
When selecting the desired price band (0, 1, 2, 3, 4, Free,
Test), the total number of selections made for that price band is
displayed.
1.3.3
dISplayIng the dIScount counterS
This function is used for displaying the total amount of discounts
and overprice accumulated for the dispensed selections.
P285U00 05 - 2007
FILLER MENU
4
1.3.4
dISplayIng the faIlure counterS
This function is used for displaying the number of times each pos-
sible failure occurred in the vending machine.
1.3.5
dISplayIng the coIn mechanISm data
1.3.5.1
dISplayIng the audIt data
This function is used for displaying the number of coins inserted in
the vending machine, differentiated by the type of coin.
1.3.5.2
dISplayIng the caShed amount
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit
1.4
dISplayIng the relatIve StatIStIcS
1.4.1
dISplayIng the SelectIon counterS
1.4.1.1
dISplayIng the SIngle counterS
This function is used for displaying the counters regarding each
selection, divided by price band (0, 1, 2, 3, 4, Free, Test).
1.4.1.2
dISplayIng the total counterS
This function is used for displaying the total counters regarding
each selection.
1.3.4 - FAIl. CNT. DISP.
1.3.5 - COIN MECH. DISP.
1.3.5.1 - AUDIT DATA DISP.
1.3.5.2 - CASH COUNT. DIS.
1.4 - DISP. REl. STAT.
1.4.1 - SEl. CNT. DISP.
1.4.1.1 - CNT DIS. X S.SEl
1.4.1.2 - TOT CNT DISPlAY
P285U00 05 - 2007
FILLER MENU
5
1.4.1.3 - SEl.NO.CNT. DIS.
1.4.2 - DISPlAY BAND CNT
1.4.3 - DISC. CNT. DISP.
1.4.4 - FAIl. CNT. DISP.
1.4.5 - COIN MECH. DISP.
1.4.5.1 - AUDIT DATA DISP.
1.4.5.2 - CASH COUNT. DIS.
1.5 - DElETE REl.STAT.
1.4.1.3
dISplayIng the SelectIon counterS In normal vendIng - maIntenance
This function is used for displaying the total counters regarding the
selections made while in normal vending mode and maintenance
mode.
1.4.2
dISplayIng the tIme band counterS
When selecting the desired price band (0, 1, 2, 3, 4, Free,
Test), the total number of selections made for that price band is
displayed.
1.4.3
dISplayIng the dIScount counterS
This function is used for displaying the total amount of discounts
and overprice accumulated for the dispensed selections.
1.4.4
dISplayIng the faIlure counterS
This function is used for displaying the number of times each fail-
ure occurred in the vending machine.
1.4.5
dISplayIng the coIn mechanISm data
1.4.5.1
dISplayIng the audIt data
This function is used for displaying the number of coins inserted in
the vending machine, differentiated by the type of coin.
1.4.5.2
dISplayIng the caShed amount
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit
1.5
deletIng the relatIve StatIStIcS
P285U00 05 - 2007
FILLER MENU
6
1.5.1 - PARTIAl RESET
1.5.1.1 - SEl. CNT. RESET
1.5.1.2 - DISC. CNT. RESET
1.5.1.3 - FAIl. CNT. RESET
1.5.1.4 - COIN MECH. RESET
1.5.2 - TOTAl RESET
1.5.1
partIal delete
1.5.1.1
deletIng the SelectIon counterS
When conrming this function, the counters regarding the different
selections are deleted.
1.5.1.2
deletIng the dIScount counterS
When conrming this function, the counters regarding discounts
and overprice are deleted.
1.5.1.3
deletIng the faIlure counterS
When conrming this function, the counters regarding the different
failure are deleted.
1.5.1.4
deletIng the coIn mechanISm data
When conrming this function, the counters regarding the coin
mechanism data are deleted.
1.5.2
total delete
When conrming this function, all relative statistics are deleted.
Indice
Altri manuali Necta Macchina per il caffè
Necta
Necta KORO PRIME ES Manuale utente
Necta
Necta Colibri Manuale utente
Necta
Necta Koro Espresso Manuale utente
Necta
Necta Krea Espresso Manuale utente
Necta
Necta brio 3 Manuale del proprietario
Necta
Necta BRIO "Easy Serving Espresso" Manuale utente
Necta
Necta BRIO Manuale utente
Necta
Necta Korinto Espresso Manuale del proprietario
Necta
Necta KORO FRESH-BREW Manuale utente
Necta
Necta Brio 250 Manuale utente
Necta
Necta Koro Manuale utente
Necta
Necta KREA TOUCH Manuale utente
Necta
Necta Brio Espresso Manuale utente
Necta
Necta KORO Fresh Brew Manuale utente
Necta
Necta Korinto UL 120V Manuale utente
Necta
Necta Kikko Max P250U00 Manuale del proprietario
Necta
Necta Korinto UL Manuale utente
Necta
Necta Kobalto espresso Manuale utente
Necta
Necta Koro Manuale utente
Necta
Necta Colibri Scheda tecnica
