Necvox FD5869 Manuale utente
Operating Instructions
7 inch Wide Screen Color Monitor
5.8 inch Wide Screen Color Monitor
5 inch Wide Screen Color Monitor
OT01003216-20020218
Important Notice
It is unlawful in most jurisdictions for a person to
drive a motor vehicle which is equipped with
a television viewer or screen that is located
in the motor vehicle at any point forward of
the back of the driver's seat, or that is visible
directly or indirectly, to the driver while op-
erating the vehicle.
CAUTION
1. Do not operate the monitor at temperatures below 32°F (0°C) or above 104°F (40°C).
2. Keep the monitor clean and dry.
3. Always seek qualified personnel to perform repairs. Never attempt your own repairs.
4. Do not drop the monitor or expose to strong impacts.
5. Do not expose to direct sunlight for extended periods of time.
2. Firmly attach dash mount on a flat surface and adjust viewing
angle of monitor by tightening the fastener at the side.
1. Slide monitor onto dash mount S2 and then tighten using
fastener.(Optional)
01
Installation Guide
02
1 To install the monitor into the seat head cushion you must ensure
that the monitor connecting cable assembly has already pull through
via the supporting pipe.
2 Before connecting the monitor, pull the connecting cable assembly
through the headrest shroud as shown in diagram 2.
3 Place headrest shroud into the opening and secure it with correct
fasteners.
Note : Installing Method of main cable assembly
1. Reeve the main cable assembly through (or beside)
the head rest support tube.
2. Secure and protect the cable assembly from damage
when the head rest is adjusted.
Installation Guide (Only for 5",5.8")
12
4 Connect the connecting cable assembly to the monitor.
5 Ensure that there is no
foreign material is trapped
inside theenclosure before
pushing themonitor onto the
headrest shroud.Make sure
that the monitor issecurely
locked in place.
HEADREST SHROUD
MONITOR
53
TRIM RING SHROUD
03
Interconnect Cable
Assembly , Monitor
Red Wire : ACC
Black Wire : Ground
Blue Wire : 12 Vdc (1A)
Output
Interconnection
Box AD-6865
Video Out
Video source 2
(Input)
Yellow Wire : Battery (+)
Wiring System :
Electrical Connections (General)
Video source 1
(Input)
Brown wire : Safety connection
(Hand - break switch)
In - Car Audio Equipment
Yellow wire : Battery (+)
Red wire : ACC
Black wire : Ground
Wiring System :
04
TV Tuner
(Stereo)
Electrical Connections
(System Upgrade)
FM Modulator
Antenna , AM/FM
88.7 MHZ
89.1 MHZ
TV Antenna
Diversity
MODE
ON / OFF and Mode
Selection
Infra-Red Remote Controller
Receiver
MODE
DOWN
Positive and Negative Adjustment
MENU
Activation of Menu Indicator
UP
Positive and Negative Adjustment
MENU
TINT
FORMAT
RESET
DIMMER
BRIGHT
FORMAT Selection
05
TINT Adjustment
Brightness Adjustment
DIMMER ON/OFF
COLOR
On Screen Display (OSD) Indicator
Color Adjustment
Reset to Original Condition
Basic Operation (Monitor)
Press Menu Key
Using Menu Function Key :
Press Menu key until OSD indicator
at the correct function mode
COLOR
BRIGHT
06
TINT
MENU
MODE
OSD will appear on screen
COLOR
BRIGHT
FORMAT
RESET
DIMMER
FORMAT
RESET
DIMMER
TINT
MODE
MENU
User Guide - Remote Controller:
Menu (Activation of OSD and
Function Selection)
Mode Selection
Down Adjustment
Up Adjustment
POWER ON / OFF
4 5 6
MEMORY
CH/DISC/SET
POWER
1 2 3
MENU
MODE
4 5 6
MEMORY
CH/DISC/SET
POWER
1 2 3
MENU
MODE
MODE Key
Note:
Press Up & Down key (CH/DISK/SET)
to select system (NTSC PAL)
MODE
AV2 : NTSC
MENU
07
Press Mode key to select the
Press or to desire setting
desired video source input
(input 1 or input 2)
AV1 : NTSC
MENU
MODE
Key
Key
Press to the desire setting
MENU
MODE
COLOR
COLOR
32
32
Press to the desire setting
MENU
MODE
4 5 6
MEMORY
CH/DISC/SET
POWER
1 2 3
MENU
MODE
4 5 6
MEMORY
CH/DISC/SET
POWER
1 2 3
MENU
MODE
4 5 6
MEMORY
CH/DISC/SET
POWER
1 2 3
MENU
MODE
MENU
MODE
VOL 32
Åã¥Üµøµ¡
VOL
AV1 : PAL
AV2 : PAL
08
FULL: 16:9 picture is fully displayed on screen.
ZOOM: Picture stretched vertically and horizontally.
NORMAL: When 4:3 picture is played on a wide screen, black bands
appear on both side of the picture.
Display Mode :
1. Press MENU to indicate OSD
2. Select FORMAT
3. PRESS to switch the screen size
ZOOM
FULL
NORMAL
OSD will appear on screen
Indice
Altri manuali Necvox Monitor
