Nedap UPASS Access Manuale utente

2013-03-22 Doc.no.5281326

This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys

no license under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifica-

tions and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in

whole orin part,without the writtenconsent of the publisher.

uPASS Access

Installation Guide

uPASS Access

FCC ID: CGDUPASSACC

IC: 1444A-UPASSACC

Compliace statement:

This device complies with part 15 of the FCC rules and to RSS210 of Industrial Canada.

Operation is subject to thefollowing two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Déclaration conformitè:

Cet appareil se conforme aux normes RSS210 exemptés de license du Industry Canada.

L'opération est soumis aux deux conditions suivantes:

(1) cet appareil ne doit causer aucune interférence, et

(2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération

non pas voulu de cet appareil.

Warning:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This device shall be installed to provide a separation distance of at least 20 cm from all persons.

uPASS Access

CONTENTS

1INTRODUCTION.......................................................................................................................................................................................4

1.1 SUPPORTED TAGS........................................................................................................................................................................4

1.2 TAG SECURITY ...............................................................................................................................................................................5

2INSTALLATION.........................................................................................................................................................................................6

2.1 SAFETY INSTRUCTION ................................................................................................................................................................6

2.2 MOUNTING INSTRUCTIONS......................................................................................................................................................6

3CONNECTIONS.........................................................................................................................................................................................8

3.1 POWER SUPPLY.............................................................................................................................................................................9

3.2 COMMUNICATION.......................................................................................................................................................................9

3.2.1 RS485..................................................................................................................................................................................9

3.2.2 USB.......................................................................................................................................................................................9

3.2.3 WIEGAND / MAGSTRIPE............................................................................................................................................10

3.3 LED CONTROL.............................................................................................................................................................................11

3.4 TAMPER SWITCH........................................................................................................................................................................11

3.5 NEDAP ANTENNA INTERFACE..............................................................................................................................................11

4UHFFREQUENCIES..............................................................................................................................................................................12

4.1 RADIO REGULATIONS..............................................................................................................................................................12

4.2 FREQUENCY CHANNEL SELECTION....................................................................................................................................12

5READER CONFIGURATION................................................................................................................................................................13

5.1 UHFTOOL SOFTWARE..............................................................................................................................................................13

5.2 SETTINGS......................................................................................................................................................................................13

5.2.1 READ DATA....................................................................................................................................................................13

5.2.2 DECODE NEDAP XS.....................................................................................................................................................14

5.2.3 RELAY / TIMING............................................................................................................................................................15

5.2.4 LED CONTROL...............................................................................................................................................................15

5.3 EXPERT SETTINGS......................................................................................................................................................................16

5.3.1 OUTPUT...........................................................................................................................................................................16

5.3.2 OUTPUT MESSAGE FORMAT...................................................................................................................................16

5.3.3 EXTRA OUTPUT............................................................................................................................................................17

5.3.4 FREQUENCY...................................................................................................................................................................18

5.3.5 READ RANGE.................................................................................................................................................................18

ATECHNICAL SPECIFICATIONS ..........................................................................................................................................................19

BPARTNUMBERS....................................................................................................................................................................................19

uPASS Access

1INTRODUCTION

The uPASS Access reader offers a revolutionary and enduring solution for hands-free door access. The uPASS

Access has the dimensions of a conventionally access control reader but offers read range unmatched in the

industry. The uPASS Access offers identification up to 2 meter (6 feet) using the latest UHF technology.

The uPASS Access includes a RS485 interface, a wiegand/magstripe and a RF-modulation interface.

The uPASS Access can also be connected to NEDAP AEOS access control hardware such as the AP1001, using the

RF-modulationinterface.

The uPASS Access does not offer the TRANSITcompatibility features.

The uPASS Access is equipped with a fixed shielded cable pigtail, 12 x 0.14 mm2, length 5 meter (15 feet). The

cable shield shall be connected to the metal case of the external device or external devices.

In the case of extending this pigtail cable, ONLY shielded cables shall be used and all shields shall beconnected

to the metal case of the external device(s).

1.1 SUPPORTED TAGS

Any EPC Class 1 Gen 2 tag is supported by the uPASS Access.

NEDAP formatted UHF tags can have the following formats:

•NEDAP UHF wiegand tags

These tags will contain all wiegand information including facility code and parity bits. All wiegand formats

can be supported. The reader transparently sends this information via the wiegand outputs. There is no

need to change any DIP-switches or configuration settings. See chapter 3.2.3 for wiring details.

Note: The Wiegandoutput format is determined by the tag and not bythereader.

•NEDAP UHF magstripe tags

These tags will contain all magstripe information. The reader transparently sends this information onto the

magstripe interface. There is no need to change any DIP-switches or configuration settings. See chapter

3.2.3 for wiring details.

Note: The magstripe output formatis determinedby the tagand not by the reader.

•NEDAP UHF XS tag

These tags are especially programmed in the same format as our 2.45GHz AVI tags (Compact-Tag, Window-

Button and Heavy-Duty-Tag). The tags will also have a customer-code and id-number. The reader will

modulate the tag-info onto the Nedap antenna interface output, which can be connected to NEDAP AEOS

access control hardware such as the AP1001.

Note: See also the 'decode nedap xs'feature as described inchapter 5.2.2.

uPASS Access

1.2 TAG SECURITY

EPC (Electronic Product Code) tags were introduced as a possible successor to the barcode with added

functionalities. The tag emits its EPC in plain text. This makes the tags vulnerable to cloning and counterfeiting

attacks. Unlike many 13MHz smartcards, EPC tags do not supportany DES, 3DES or AES encryption.

EPC tags contain a data field known as the Tag Identifier (TID). At the discretion of the EPC manufacturer, the

value may be factory programmed and locked, ensuring that tags have a unique identity and (theoretically)

cannot be cross-copied. This TID based anti-cloning mechanism is notconsidered to be a strong protection.

NEDAP UHF tags support a locked serialized TID and the uPASS Access reader can be configured to read the TID

data field.

In addition NEDAP has also implemented an advanced anti-cloning and anti-counterfeiting method based upon

a two way authentication. This feature is supported in combination with all NEDAP UHF tags.

By default the uPASS Access reader is configured to read any EPC tag.

We encourage customers to enable the TID-check or the two way authentication. But also advise not to

completelyrelyon these methods in high-security applications.

uPASS Access

2INSTALLATION

2.1 SAFETY INSTRUCTION

The followingsafetyprecautions should be observed duringnormal use, service and repair.

•The uPASS Access may only be installed and serviced by qualified service personnel.

•Disconnect the power supply before (dis)connecting any wires, uPASS Access is NOT hot-swappable, so

when making or changing connections, power must be switched OFF.

•The cable shield shall be connected with safety ground and the metal case ofthe external device(s).

•To be sure of safety, do not modify or add anything to the uPASS Access other than mentioned in this

installation guide or indicated by NEDAP N.V.

2.2 MOUNTING INSTRUCTIONS

The uPASS Access can be mounted to any surface, including directly to metal. See the picture below for details

about the dimensions.

Figure1: uPASS Access dimensions (mm)

Mount the base-plate on the required location.

Ensure that it is placed correctly covering the cable entry hole. Properly fix the base-plate into its position using

the 2 screws. When mounting on a stone or concrete wall drill 5mm holes for the plugs. When mounting on

wood, drill with 2.5mm.

uPASS Access

Install the uPASS Access reader onto the base-plate.

1. Feed the cable through the cable entry hole. Important note: minimum bending radius 30mm.

2. Attach the top of the uPASS Access onto the base-plate.

3. Fix the assembly using the screw on the bottom.

Figure2: uPASS Access installation

uPASS Access

3CONNECTIONS

The uPASS Access is supplied with a 5 meter (15 feet) shielded cable pigtail with 12 multi-colorwires.

RED

Power supply 12- 24VDC.

BLACK

Power supply 0VDC, DC-Ground.

BROWN

RS485 A-

GREEN

RS485 A+

GRAY

Data-0 / Clock

PINK

Data-1 / Data

YELLOW

Tamper switch (normally closed)

GRY/PNK

Tamperswitch (common)

RED/BLU

Led_UL_IN*

WHITE

Led_NA_IN*

PURPLE

Nedap antenna interface. RFMOD antenna modulation. Connect to ANT.

BLUE

Beeper_IN*

SHIELD

Shield

Note: Cable shieldshall beconnected to the metalcase ofthe external device(s).

Cableextensionsshall only be made by means of shielded cable(s).

All shields of the shielded cableextensions shallbe connected together and to the metalcase of the external

device(s).

Led_UL_IN*, Led_NA_IN* and Beeper_IN* are inputs that are active LOW.

uPASS Access

3.1 POWER SUPPLY

The uPASS Access requires DC power supply in the range from 12 – 24V.

Maximum current consumption is 1A @ 12VDC, 0.5A @ 24VDC.

Connections:

RED

Power supply 12- 24VDC.

BLACK

Power supply 0V / DC-ground.

SHIELD

Shieldconnectedto DC-ground .

Note: Extending thisconnection beyond the 5 meter pig tail lengthshall ONLY be allowed using shielded cable.

The minimum voltage at the end of the fixed shieledpigtailcable shall be greather then 12VDC -10%

The shield shall be connectedto the metal case of the external device.

3.2 COMMUNICATION

3.2.1 RS485

The uPASS Access reader has a RS485 interface for communication with a host system or for configuring reader

settings. The RS485 interface is a 2-wire half-duplexserial communication interface using balancedlines.

Connections:

BROWN

RS485 A- Balanced RX/TX

GREEN

RS485 A+ Balanced RX/TR

SHIELD

Shieldconnectedto DC-ground.

Note: The RS485 interface isdisabledwhile theUSB interfaceis in use!

Extending thisconnection beyond the 5 meter pig tail length shall ONLY be allowed using shieldedtwistedpair

cable(2 x 2 x 0.25 mm2)as long as the total length is shorter then 1200meters, 6000 feet, cable capacity < 100

pF/meter.

The secondtwisted pair shallbe used for the DC power supply.

The shield shall be connectedto the metal case of the external device.

3.2.2 USB

The uPASS Access reader features an USB interface for service, installation and firmware upgrade purposes. The

Mini-USB connector is located on the bottom of the device and can only be reached when the bottom screw is

opened and the uPASS Access is lifted away from the base-plate. This ensures that unauthorized modifications

to the reader settings can be detected using the tamperswitch.

The USB interface can be used to configure the reader using the UHFTOOLsoftware.

Note: While the shielded USB cable is connected, the RS485interfaceis disabled!

The maximum shieldedcable length shall be < 2meter.

USB Driver installation

Make sure your computer is connected to the internet. The driver should install automatically via Windows

update when the uPASS Access reader is connected to your PC via the USB cable. Follow the driver installation

wizard. If you do not see the Windows update pop-up, you can manually install the driver. To manually install,

you need to go to FTDI’s website at www.ftdichip.com/Drivers/VCP.htm and download the VCP (Virtual Com

Port) drivers for your operating system. Drivers for MacOS and Linux are available as well.

uPASS Access

3.2.3 WIEGAND / MAGSTRIPE

The wiegand interface connections also support magstripe.

NEDAP UHF Wiegand tags will generate a wiegand message on the interface.

NEDAP UHF Magstripe tags will generate a magstripe message on the interface.

OtherUHF tags will not generate a message on this interface,unless the 'Extra output' settings are used!

The wiegand/magstripe output format is determined by the programmed format of the tag.

Make sure to order the correct tag formatting if you want to use the wiegand or magstripe interface. See also the

UHF tags order guide for more information.

Connections:

Wiegand connections Magstripeconnections

GRAY

Data-0 Clock

PINK

Data-1 Data

BLACK

Ground Ground

SHIELD

Shieldconnectedto DC-ground.

Note: Extending these connections beyondthe 5 meterpig tail lengthshall ONLY be allowed usingshielded cable (4 x

0.25 mm2) as long as the total length isshorter then 150 meters (500 feet).

The shieldshall be connected tothe metalcase of the external device.

3.2.3.1 WIEGAND TIMING

In the figure below the Wiegand protocol timingis specified.

Tpw

DATA-1

DATA-0

Tpi

Tpw

Timing constants:

Tpi Pulse interval time 1msec

Tpw Pulse width time 50µsec

Figure3: Wiegand protocol timing

3.2.3.2 MAGSTRIPE TIMING

The magstripe message length is determined by the tag. The first character will be a start-sentinel (0xB). The

message is terminated with an end-sentinel character(0xF) and an LRC character.

The figure below shows the timing for one magstripe character. Each bit consists out of one period low

(220µsec) and two periods high (440µsec). The Data-signal is valid and stable on the falling edge of the Clock-

signal. Before andafter the data 16 clock pulses are generated (postamble and preamble).

odd parity

msb

lsb

3300µsec

220µsec

660µsec

CLK

DAT

Timing constants:

Clock period 660µsec

Clock high 440µsec

Clock low 220µsec

Data pre-amble 16 clock periods

Data post-amble 16 clock periods

Figure4: Magstripe protocol timing one character

Altri manuali per uPASS Access

Indice

Manuali Serratura della porta popolari di altre marche

Assa Abloy

Assa Abloy effeff 827A-IP Manuale utente

We.lock

We.lock SECBNEBL51 Manuale utente

Iseo

Iseo MA1A Manuale utente

ID Lock

ID Lock 150 Manuale utente

Lockly

Lockly ACCESS TOUCH PRO Manuale utente

iLoq

iLoq G50S Manuale utente

SDC

SDC Z7835 Manuale utente

ilco

ilco 452 Manuale utente

Samsung

Samsung shs-h705 Manuale utente

TRU-BOLT

TRU-BOLT 08102017 Manuale utente

CDVI

CDVI 500-LADJ Manuale utente

Igloohome

Igloohome Deadbolt 2S Metal Grey Istruzioni di installazione e manutenzione

eSSL

eSSL FL-300 Manuale utente

JAKO

JAKO JKBTNX4 Manuale utente

Dorma

Dorma MUNDUS PREMIUM GK 50 Guida utente

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuale utente

Yale

Yale MORTISE 8800 SERIES Manuale utente

Siegenia

Siegenia KFV AS3500 Manuale utente

Nedap uPASS Access Manuale utente

Manuali Serratura della porta popolari di altre marche