Nedap TRANSIT Entry Manuale utente

TRANSIT Entry

Installation Guide

FCC ID: CGD-TRANSITENTRY

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

2007-09-26 Part #: 5268605

This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its

publication conveys no license under any patent or other right, nor does the publisher assume liability for any

consequence of its use; specifications and availability of goods mentioned in it are subject to change without

notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher.

TRANSIT Entry

CONTENTS

CONTENTS............................................................................................................................................. 2

1INTRODUCTION .......................................................................................................................... 3

1.1 PRODUCT DESCRIPTION .............................................................................................. 3

1.2 OPTIONAL CARD TECHNOLOGY READER INTERFACE ...................................... 3

2INSTALLATION............................................................................................................................. 4

2.1 SAFETY PRECAUTIONS.................................................................................................. 4

2.2 MOUNTING INSTRUCTIONS........................................................................................ 4

2.3 ADJUSTABLE MOUNTING BRACKET......................................................................... 5

2.4 OPENING THE SERVICE COVER .................................................................................. 6

2.5 INSTALLING AN OPTIONAL INTERFACE BOARD.................................................. 7

2.5.1 AVAILABLE INTERFACE BOARDS ................................................................ 7

2.5.2 INSTALLATION PROCEDURE ........................................................................ 8

3CONNECTIONS ............................................................................................................................ 9

3.1 POWER SUPPLY .............................................................................................................10

3.2 COMMUNICATION .......................................................................................................11

3.2.1 RS232 CONNECTION.....................................................................................11

3.2.2 RS422 CONNECTION.....................................................................................12

3.2.3 WIEGAND, MAGSTRIPE, BARCODE CONNECTION .............................13

3.2.4 USB CONNECTION .........................................................................................14

3.3 DIGITAL I/O .....................................................................................................................15

3.3.1 RELAY OUTPUT................................................................................................15

3.3.2 READ DISABLE INPUT....................................................................................16

3.3.3 GENERAL PURPOSE INPUTS .......................................................................17

3.3.4 GENERAL PURPOSE OUTPUTS...................................................................18

3.3.5 TAMPER SWITCH.............................................................................................19

4DIP-SWITCH SETTINGS ...........................................................................................................20

4.1 RANGE BEEPER ON / OFF ...........................................................................................20

4.2 RS232 / RS422 SELECTION.........................................................................................20

4.3 UNUSED SW1-3 AND SW1-4.....................................................................................20

5LED INDICATIONS ....................................................................................................................21

6FREQUENCY SELECTION........................................................................................................22

7READ RANGE CONTROL (SQUELCH) .................................................................................23

7.1 PRINCIPLE ........................................................................................................................23

7.2 READ RANGE ADJUSTING..........................................................................................23

8IDENTIFICATION .......................................................................................................................24

8.1 STANDARD OPERATING PROCEDURE...................................................................24

8.2 USING THE MTR MODULE..........................................................................................24

9FIRMWARE UPGRADE .............................................................................................................25

ATECHNICAL SPECIFICATIONS...............................................................................................26

BPART NUMBERS.........................................................................................................................27

TRANSIT Entry

1INTRODUCTION

1.1 PRODUCT DESCRIPTION

Nedap’s handsfree access solution represents the latest in technology for secure

handsfree doors access and other RFID applications. TRANSIT Entry combines the

convenience of traditional door automation with the security of restricted areas.

It makes a perfect fit to any door or vehicle gate environment where handsfree

access is required. The system reads at distances up to 4 meter (12 feet) reliable and

consistently. This has great appeal to people, especially in situations where it is

inconvenient to use their hands when presenting an ID badge when accessing a

door, but where high security needs to be maintained.

Moreover it offers handsfree vehicle access to gated areas. Vehicles are identified

at a range up to 4 meters (12 feet), without the hassle of having to open the window

to present a card.

The handsfree access system is made up of a TRANSIT Entry reader and a

transponder. TRANSIT Entry readers are installed next to a door or gate. A long

range transponder visible in line of sight of the reader will be identified at

distances up to 4 meter (12 feet).

1.2 OPTIONAL CARD TECHNOLOGY READER INTERFACE

The TRANSIT Entry reader also features an optional proximity and ISO compliant

smartcard interface. This Multi-Technology Reader Module (MTR) enables the

reader to read standard proximity cards and smartcard CSN. This also allows the

reader to operate with existing credentials when presented to the face of the

reader.

The MTR supports the following card technologies:

•120-125 kHz: HID prox, Nedap and EM read-only.

•13.56 MHz: HID iClass CSN, MIFARE, LEGIC Advant UID, ISO14443A and

ISO15693.

TRANSIT Entry

2INSTALLATION

2.1 SAFETY PRECAUTIONS

The following safety precautions should be observed during normal use, service

and repair.

•The TRANSIT Entry must be connected with safety ground.

•The TRANSIT Entry may only be installed and serviced by qualified service

personnel.

•Disconnect the power supply before removing or installing any parts.

•To be sure of safety, do not modify or add anything to the TRANSIT Entry other

than mentioned in this installation guide or indicated by NEDAP N.V.

2.2 MOUNTING INSTRUCTIONS

The TRANSIT Entry can be mounted to any surface, including directly to metal.

Locate an appropriate position. Use the upper two keyholes (K) to mount the

reader. Open the service cover to secure the reader using the two lower mounting

positions (L).

See the picture below for details about the dimensions and the locations of the

mounting positions.

service cover

200mm (7.87"

)

47mm (1.85")

220mm (8.66")

108mm (4.25")

35mm171mm (6.73") (1.38")

63mm (2.48")

4.5mm (.17")

∅5mm

(.20")

∅4.5mm

(.17")

rear viewfront view side view

Figure 1: TRANSIT Entry reader dimensions

TRANSIT Entry

2.3 ADJUSTABLE MOUNTING BRACKET

With the adjustable mounting bracket, the TRANSIT Entry can be ‘aimed’ at the

desired detection area. It can also be used for mounting the reader to round or

square masts (see appendix Bfor part numbers).

Figure 2: Adjustable mounting bracket

Once the adjustable mounting bracket is assembled, attach the bracket to the wall

or mast. After that the TRANSIT Entry can be mounted onto the bracket. The ball

and socket joint can be used to adjust the reader’s orientation. Tighten the hex

screw on top of the joint to fix the correct orientation.

Note: Maximum diameter for round masts 125mm (

4.9 inch

)

Maximum diameter for square masts 100mm (

3.9 inch

)

123mm (4.84") 47mm (1.85")

61mm (2.40")

120mm (4.72")

15mm (.59")

88mm (3.46")

side view rear view

∅4.5mm

(.17")

Figure 3: Adjustable mounting bracket dimensions (in mm)

TRANSIT Entry

2.4 OPENING THE SERVICE COVER

The service cover can be opened to access the connections, control the read

range, setup the operating frequency and view the LED indicators.

Open the screws on the bottom of the device to unlock the service cover. Once

the service cover is unlocked, lift it off.

Figure 4: Opening the service cover

Note: Make sure the screws are completely opened (and closed when placing

the cover back on). Don’t worry about losing the screws, they cannot fall

out.

TRANSIT Entry

2.5 INSTALLING AN OPTIONAL INTERFACE BOARD

Make sure to follow all safety precautions outlined in chapter 2.1 and disconnect

the power supply when installing or replacing an optional interface board.

2.5.1 AVAILABLE INTERFACE BOARDS

Various optional interface boards are also available for the TRANSIT Entry.

Ethernet (TCP/IP) interface board

Connects the TRANSIT Entry to an Ethernet network using the

TCP/IP protocol.

See for detailed information about the Ethernet communication

board its user's manual.

MTR Module (Multi Technology Reader Module)

The MTR Module enables proximity reading of many transponders

types such as HID Prox, EM read-only, Mifare and HID iCLASS.

HIB (HID Interface Board)

Enables the reading of HID prox cards with an HID Prox Booster.

See appendix Bfor part numbers.

TRANSIT Entry

2.5.2 INSTALLATION PROCEDURE

1. Disconnect the power supply.

2. Remove the complete front cover from the TRANSIT Entry.

3. Place the interface board on the 14-pin header K1. Make sure it’s firmly

positioned and makes good contact with connector K1.

Figure 5: interface board installation

4. Tighten the two screws to fix the board into place.

5. Read the board’s installation guide for additional notes like address settings,

jumper settings and wiring details.

6. Replace the front cover on the TRANSIT Entry.

TRANSIT Entry

3CONNECTIONS

Wire connections to the TRANSIT Entry are user friendly spring cage terminal

connectors.

Connection procedure with spring cage terminal connectors.

1. Strip wire lead for about 9 mm (0.35 inch).

2. Push the screwdriver straight down to release the

spring cage. Use a slotted, narrow-head

screwdriver.

3. Insert the wire lead into the wire terminal.

4. Remove the screwdriver, this clamps the wire.

5. Gently pull on the installed wire to make sure the

connection is reliable.

Wire

Lead

Screwdriver

Figure 6: Wiring detail

Note 1: Each connector terminal can accommodate only 1 solid or stranded wire.

Note 2: Wiring is normally done without ferrules. However, it is possible to use

ferrules, provided that they are properly crimped.

See appendix Afor recommended maximum and minimum conductor cross

sections and for the recommended wire stripping length.

TRANSIT Entry

3.1 POWER SUPPLY

The TRANSIT Entry requires DC power supply in the range from 12 – 24V.

Maximum current consumption is 1A @ 12VDC, 0.5A @ 24VDC.

Connections:

DC- Power supply 0V. Should be connected to a protective earth

connection.

DC+ Power supply 12 - 24VDC.

Note: The power supply connection has an auto resetting fuse protection.

DC+

DC-

Power supply

Figure 7: Power supply wiring

Altri manuali per TRANSIT Entry

Indice

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente