Neets Control SieRRa DK Manuale utente

Page 1 Doc. no#: 310-0100-004-001 R200 Manual

Foreword:

The purpose of this document is to describe how to install and configure the Neets Control –SieRRa DK and EU

models.

of Neets. All rights are reserved. You may not allow any third party access to content, information or data in

this manual without Neets’ express written consent.

CHANGES - Neets reserve the right to change the specification and functions of this product without any

notice.

Questions, AFTER reading this manual, can be addressed to your local dealer or:

Neets

Langballe 4

8700 Horsens

Denmark

by E-Mail: Suppor[email protected]

or you may use our contact form at www.neets.dk

Revision list:

Author: Date

Description

Pages

TSA 07/03-11

First release.

All

DB 08/03-12

New company address

Doc. no#: 310-0100-004-001 R200 Manual Page 2

Table of content

Foreword............................................................................................................................................... 1

Revision list ........................................................................................................................................... 1

Table of content..................................................................................................................................... 2

Description ............................................................................................................................................ 3

Connections on units.............................................................................................................................. 4

Technical description ............................................................................................................................. 5

USB............................................................................................................................................. 5

RS-232 Port ................................................................................................................................ 5

IR/RS-232 ports .......................................................................................................................... 6

uSD-Card .................................................................................................................................... 6

I/O Ports..................................................................................................................................... 7

LAN............................................................................................................................................. 7

Fault finding........................................................................................................................................... 8

System log file............................................................................................................................ 9

Page 3 Doc. no#: 310-0100-004-001 R200 Manual

Description:

Neets Control –SieRRa is the best of both worlds (touch screen interface combined with hardware buttons).

An extra dimension is added by a built-in web server, which means you can use a secondary touch panel to get

more functions.

To get an unlimited number of buttons you can use for instance a smart phone, PC or touch panel (e.g. Android

tablet, Ipad, Ipod touch).

Other special features are a flexible and recognizable design between small and big room installations, level

indication and easy installation.

Neets Control –SieRRa is available in polar white and anthracite.

Front view:

Back view:

Doc. no#: 310-0100-004-001 R200 Manual Page 4

Description

Neets Control - SieRRa

RS-232 (Rx/Tx)

RS-232 (Tx) / IR (controls up to 4 devices)

LAN device control

Expansion bus (for level knot, real-time clock, extra buttons…)

I/O

Micro SD card

Real time clock

Add on board

Buttons

LED

LED colors (Green, Red, Blue, Orange, Turquoise, Purple, White)

USB port for programming

PIR sensor input

Yes

Light on/off

Yes

Room darkening

Yes

Screen up/down

Yes

Volume control (with LED level)

Yes

Alarm when RS-232 device is removed

Yes

Device feedback

Yes

Connections on units

DK version

EU version

Number

Description

Extern 12V DC input

RS-232 port

RS-232 or IR control out

NEB Neets External Bus (for adding e.g. level control, RS-485, RTC, extra buttons)

Input/Output

LAN

Page 5 Doc. no#: 310-0100-004-001 R200 Manual

Technical description

Technical details:

RS-232

Baud: 1200-115200

Data bit:7/8

Parity: none, even, odd

Stop bit: 1/1,5/2

Transmit 381 Hz –500 KHz

LAN

10/100 MBit

Input

Sence low < 1 VDC

Sence high > 4 VDC

Output

Open drain

Max voltage: 24 VDC

Max current: 0,5 A

Power

12VDC (110-230VAC Adapter included)

USB

The USB port can only be used to program the Neets Control –SieRRa from the

Neets Project designer software. It cannot be used to control any devices what

so ever.

From the USB you can also power the system. This is to be used in programming

situations, so you do not have to connect 12VDC to the unit to program it.

The USB connector needed to connect to the Neets Control –SieRRa is of the type

mini USB B 5P. You can either buy this cable from Neets or via the web (buy a USB A

to Mini USB B 5P). The cable type is also widely used for MID device and compact

cameras and so on.

RS-232 Port

The onboard RS-232 port (TX-1 and RX-1) is used for two way

communication. This port is used for the device you want to use reply on

(e.g. your projector). It can also be used for uploading settings to the unit

(be aware that this is the most slow way to do this).

To connect the Neets Control - SieRRa you must wire the RS-232 cable as

shown here to the right. This is a Female 9 pin SUB-D connector that will fit

into a standard computer RS-232 port, or any USB to RS-232 converter.

EU version

DK version

Doc. no#: 310-0100-004-001 R200 Manual Page 6

IR/RS-232 ports

The SieRRa has 2 ports (TX-2 and TX-3) that can be configured (in software) either as RS-232 or as IR emitter.

uSD-Card

The uSD-Card is used to storage firmware, homepage and the settings.

Under normal operation, removal of the uSD-Card is not needed.

If needed, you can copy the settings and the firmware directly onto the card.

To remove the uSD Card from the unit, please first remove the front plastic

(all the buttons).

Bellow those you will find the uSD-Card, please be very careful when you

remove the card.

When used as RS-232 transmit port:

Connect the device to e.g. TX-2 and

GND, as shown here above.

When used as single IR port:

Connect the IR emitter to e.g.

TX-2 (white striped wire) and

GND, as shown here above.

When used as dual IR port:

Connect the IR-1 emitter to e.g. TX-2

(white striped wire) and black wire on

IR-1 emitter to IR-2 emitter (white

striped wire), and black wire from IR-2

emitter to GND, as shown here above.

Junction

REMEMBER to remove power

from the unit before removing

Micro SD card!

Page 7 Doc. no#: 310-0100-004-001 R200 Manual

I/O Ports

The Neets Control –SieRRa has 3 I/O’s onboard. They can be used for external

keyboard, PIR (movement) sensor, keyboard lock, extra relays and so on.

The ports are not potential free, which means you will need external relays, if you

need to prevent e.g. ground loops.

When used as output they are active low (when the software says activated, the

pin are tied to GND through a FET transistor - also called open drain/collector

function). You can draw up to 24VDC/500mA.

When used as input the voltage has to be below 1 Volt DC to be accepted as LOW, and

above 4 VDC (but below 24 VDC) to be accepted as high.

LAN

The network connector is for connecting the system to the local area network.

There are two LED’s on the connector. They have the following meaning:

Color:

Off

Blink

Yellow

No Link

Link

Activity

Green

10Mbit

100Mbit

Default IP settings are:

IP address:

192.168.254.253

Subnet:

255.255.255.0

10/100Mbit:

Auto

DHCP:

Disabled

Doc. no#: 310-0100-004-001 R200 Manual Page 8

Fault finding

When errors occur the LED will indicate this. The following will give you a guide to find these errors.

In the Neets Control –SieRRa the LED´s are placed here:

Fault

Solution

uSD-card missing

Control that the uSD-card is mounted correctly and that

the uSD-card you are using are formatted with FAT.

Unexpected Error

There are properly problems in the project you have

uploaded. Try e.g. to upload a empty project and see if this

works or contact Neets or your local dealer.

Error in serial number

During the production of the unit, something has gone

wrong. You need to return the unit to Neets or your local

dealer for replacement/repair.

Unzipping config.zip

file after power on

If you have placed a project file manually on the uSD-card,

the system will extract the files needed to run the project.

After extraction, the system will start to run the project.

Unable to start the

project

This scenario often happens, when the uSD-card in the

unit is replaced with a blank uSD-card.

Alternatively, there can be a problem in the project you

have uploaded. In this case e.g. try to upload an empty

project and see if this works - or contact Neets or your

local dealer.

Page 9 Doc. no#: 310-0100-004-001 R200 Manual

Fault

Solution

System are in boot

mode

You have put the system in boot mode.

This mode allows you to communicate with the system

using Rx1/Tx1. To get the system in boot mode, hold down

all 4 corner buttons for more than 2 seconds (2 in the top,

and 2 in the botton).

System are resuming

factory default

settings

When pressing Switch 1 and 4 during power on,

the system will delete the current settings and resume

factory default.

This method are only intended to be used, if the control

system lock up and enters “Unexpected Error”.

System log file

The Neets Control –SieRRa has a log file, which contains information, warnings and errors that the system

encounters during run.

The log file looks like below:

To give you the best support possible we recommend that you have access to the log file, when contacting

support.

There are two ways to get access to this file:

uSD-card:

If you put the uSD-card into your computer you find the log file here: Drive\System\Log.txt

HTTP:

Enter the following address into your browser: http://xxx.xxx.xxx.xxx//System/Log.txt.

xxx.xxx.xxx.xxx are the IP address of your Neets Control –SieRRa.

Remember the two“//”.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo