Neilsen DR CT1080 Manuale utente
AIR IMPACT WRENCH -1/2” DR
CT
ORIGINAL INSTRUCTIONS
SAVE THESE
INSTRUCTIONS AND PRECAUTIONS.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
Cannon Tools Limited
Address:
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
CT
1080
INSTRUCTIONS AND PRECAUTIONS.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
2
3
EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety and
health requirements of the EC Directive based on its design and type, as brought
into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will
lose its validity.
Product description:AIR IMPACT WRENCH -1/2”DR
Model: CT1080
Applicable EC Directives:
EC Machinery Directive 2006/42/EC
Harmonized standards
EN ISO 11148-6
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2016-09-18
4
SYMBOLS
In this manual and/or on the machine the following symbols are used:
WARNING:
IMPORTANT SAFETY INFORMATION ENCLOSED. READ THIS MANUAL BEFORE
OPERATING TOOL. IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE
INFORMATION IN THIS MANUALINTO THE HANDS OF THE OPERATOR. FAILURE TO
OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
FOR USE
•
Impact wrenches are designed for use in general automotive repair, body shops, front end
service and light truck and farm equipment applications.
PLACING TOOL IN SERVICE
• Always operate, inspect and maintain this tool in accordance with all regulations (local, state,
federal and country), that may apply to hand held/hand operated pneumatic tools.
• For safety, top performance, and maximum durability of parts, operate this tool at 0.65Mpa
maximum air pressure at the inlet with 3/8” (10 mm) inside diameter air supply hose.
• Always turn off the air supply and disconnect the air supply hose before installing, removing or
adjusting any accessory on this tool, or before performing any maintenance on this tool.
• Do not use damaged, frayed or deteriorated air hoses and fittings.
• Be sure all hoses and fittings are the correct size and are tightly secured.
• Always use clean, dry air at 0.65Mpa maximum air pressure. Dust, corrosive fumes and/or
excessive moisture can ruin the motor of an air tool.
• Do not lubricate tools with flammable or volatile liquids such as kerosene, diesel or jet fuel.
Denotes risk of personal injury, loss of life or damage to the tool in
case of non-observance of the instructions in this manual.
Wear hearing protection.
Wear safety goggles.
Contact with or inhalation of dust coming free during use (e.g.
lead-painted surfaces, wood and metal) can endanger your health
and the health of bystanders. Always wear appropriate protective
equipment, such as a dust mask. Always use proper dust
extraction during use.
Wear gloves.
5
• Do not remove any labels. Replace any damaged label.
• Always wear eye protection when operating or performing maintenance on this tool.
• Always wear hearing protection when operating this tool.
• Keep hands, loose clothing and long hair away from rotating end of tool.
• Note the position of the reversing lever before operating the tool so as to be aware of the
direction of rotation when operating the throttle.
•Anticipate and be alert for sudden changes in motion during start up and operation of any
power tool.
• Keep body stance balanced and firm. Do not overreach when operating this tool. High
reaction torques can occur at or below the recommended air pressure.
• Tool shaft may continue to rotate briefly after throttle is released.
• Air powered tools can vibrate in use. Vibration, repetitive motions or uncotmfortable positions
may be harmful to your hands and arms. Stop using any tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Use only impact sockets and accessories. Do not use hand (chrome) sockets or accessories.
• Impact wrenches are not torque wrenches. Connections requiring specific torque must be
checked with a torque meter after fitting with an impact wrench.
NOTICE
The use of other than replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by trained personnel.
ADJUSTMENTS
SETTING THE POWER REGULATOR
WARNING! Impact wrenches are not torque control devices. Fasteners with specific torque
requirements must be checked with suitable torque measuring devices after installation with an
impact wrench.
Impact Wrenches incorporate a power regulator into the reverse mechanism that allows the
operator to have either full power output in one direction and reduced power output in the other
direction or full power output in both directions. To adjust the power, proceed as follows:
For full power in both directions. rotate the reverse valve until the notch on each end of the
reverse valve aligns with the number 5 on each side of the housing.
NOTICE! The numbers 0 thru 5 on the housing are only for reference and DO NOT denote a
specific power output. Zero (0) designates the lowest power output while five (5) denotes the
highest.
6
For reduced power in the forward direction and full power in the reverse direction, push the
reverse valve inward on the right side of the tool and rotate the reverse valve until the notch on
the right side aligns with the desired number on the right side. This provides reduced power in
forward but full power in reverse when the reverse valve is pushed in the opposite direction.
For reduced power in the reverse direction and full power in the forward direction, push the
reverse valve inward on the left side of the tool and rotate the reverse valve until the notch on
the left side aligns with the desired number on the left side. This provides full power in forward
but reduced power in reverse when the reverse valve is pushd the opposite direction.
RECOMMENDED ARRANGEMENT OF AIR PIPING AND AIR LINE SYSTEM
SPECIFICATION:
Free speed: 7000/min
Max. torque: 425 ft/lb
Air consumption: 8cfm
Max. operating pressure: 0.65Mpa
Air inlet: 1/4"
7
ASSEMBLY DIAGRAM AND PARTS LIST
8
CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Made in China
Indice
Altri manuali Neilsen Avvitatore a impulsi
