nekos
products have been manufactured in accordance with safety standards and
conforms to the stipulations of current standards in force.
When correctly assembled, installed and used according to the present instructions, they
will not generate any danger for
Symbols used in the manual
DANGER
Contents
1.
Security rules
................................
2.
Technical operating information
3.
Formulas and
recommendations for installation
3.1.
Calculation of opening / closure force
3.2.
Maximum opening based on sash height
4.
Construction and regulatory references
5.
Id plate and marking data
................................
6.
Technical data
................................
7.
Electric power supply
................................
7.1.
Selecting the cross
8.
Electrical connection
................................
9.
Instructions for assembly
................................
9.1.
Prepar
ation for mounting the actuator……………………………………… 10
9.2.
9.3.
windows
................................
10.
Programming the actuator
................................
10.1.
10.2.
RESET Procedure
................................
10.3.
Overlap acquisition
................................
10.4.
LED Light signals
................................
11.
Checking for correct assembly
12.
Emergency manoeuvres, maintenance or cleaning
13.
Environmental protection
................................
14.
Certificate of guarantee
................................
15.
Declaration of
incorporation (for a partly completed machine) and EC Declaration
of Conformity
................................
3
products have been manufactured in accordance with safety standards and
conforms to the stipulations of current standards in force.
When correctly assembled, installed and used according to the present instructions, they
will not generate any danger for
persons, animals or items.
Symbols used in the manual
This indication draw the attention about potential dangers for
safety and health of peoples and animals.
................................
................................
................................
Technical operating information
................................
................................
recommendations for installation
................................
Calculation of opening / closure force
................................
.........................
Maximum opening based on sash height
................................
Construction and regulatory references
................................
................................
................................
................................
................................
................................
................................
................................
................................
............................
section of the power supply cables
...............................
................................
................................
.............................
................................
................................
ation for mounting the actuator……………………………………… 10
................................
................................
-
hung windows opening outwards or bottom
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
Checking for correct assembly
................................
................................
Emergency manoeuvres, maintenance or cleaning
................................
................................
................................
................................
................................
incorporation (for a partly completed machine) and EC Declaration
................................
................................
................................
products have been manufactured in accordance with safety standards and
When correctly assembled, installed and used according to the present instructions, they
This indication draw the attention about potential dangers for
safety and health of peoples and animals.
................................
........ 4
................................
............ 5
................................
..................... 5
.........................
5
................................
.................... 6
................................
. 6
................................
...................... 6
................................
...... 7
............................
7
...............................
8
.............................
8
................................
...................... 9
ation for mounting the actuator……………………………………… 10
................................
................. 10
hung windows opening outwards or bottom
-hung
................................
........ 10
................................
................... 11
................................
............ 11
................................
.................... 12
................................
................... 12
................................
..................... 13
................................
............ 14
................................
............. 15
................................
.................... 15
15
incorporation (for a partly completed machine) and EC Declaration
................................
...... 16
1. Security rules
C
PERSONAL SAFETY
.
I
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard
IEC 60335-2-
103 (Particular requirements for drives for gates, doors and windows) and
other directives and regulations indicated in the attached Declarations of Incor
CE Conformity (at the end of the manual). According to the Machinery Directive, actuators
are “partly completed machinery” intended for incorporation into doors and windows. The
manufacturer/supplier of the window is required, with exclusive r
compliance of the entire system with the applicable standards and to issue CE certification.
We strongly discourage any use of the actuators other than that specified and therefore, in
any case, the supplier of the complete sys
For systems installed at a height of less than 2.5 m above floor level or other levels
accessible to users, the manufacturer/supplier of the window must conduct
regarding potential harm (violent blows, crushing, wounds) caused to people by normal use
or possible malfunction or accidental breakage of the automated windows, and to
implement suitable
r
ecommended by the specified standard:
-
controlling the actuators via a “deadman’s button” placed near the system and within
the operator’s field of view, to ensure that people are out of the way during operation.
The button must be placed at a height of 1.5
public; or:
-
use of contact safety systems (also included in the actuators) that ensure a maximum
closing force of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of
IEC 60335-2-103; or:
- use of non-
contact safety systems (lasers, light grids); or:
-
use of fixed safety barriers that prevent access to moving parts.
Automated windows are deemed adequately protected if they:
-
are installed at a height of >2.5 m; or:
- have a leading-
-
are part of a smoke and heat evacuation system for emergency use only.
In any case, moving parts of windows that could fall below 2.5 m following breakage of a
system component need to be fixed or secured in
falling or collapsing: e.g. the use of safety arms on bottom
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience
allow children to play with the fixed controls and keep any remote
their reach.
The actuator is destined exclusively for installation indoors. For any special
application we recommend you consult the manufacturer
After removing packaging, check for any damage on the appliance.
Always request exclusive use of original spare parts. Failure to respect this condition
could compromise safety and invalidate the benefits contained in the warranty for the
appliance.
In the event of any problems or queries, consult your agent or contact the
manufacturer directly.
4
THE FOLLOWING INSTAL
SIS AND PROTECTION MEASURES
.
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard
103 (Particular requirements for drives for gates, doors and windows) and
other directives and regulations indicated in the attached Declarations of Incor
CE Conformity (at the end of the manual). According to the Machinery Directive, actuators
are “partly completed machinery” intended for incorporation into doors and windows. The
manufacturer/supplier of the window is required, with exclusive r
esponsibility, to ensure the
compliance of the entire system with the applicable standards and to issue CE certification.
We strongly discourage any use of the actuators other than that specified and therefore, in
any case, the supplier of the complete sys
tem retains full liability.
For systems installed at a height of less than 2.5 m above floor level or other levels
accessible to users, the manufacturer/supplier of the window must conduct
regarding potential harm (violent blows, crushing, wounds) caused to people by normal use
or possible malfunction or accidental breakage of the automated windows, and to
in view of these. Such measures include those
ecommended by the specified standard:
controlling the actuators via a “deadman’s button” placed near the system and within
the operator’s field of view, to ensure that people are out of the way during operation.
The button must be placed at a height of 1.5
m and operated by key if accessible to the
use of contact safety systems (also included in the actuators) that ensure a maximum
closing force of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of
contact safety systems (lasers, light grids); or:
use of fixed safety barriers that prevent access to moving parts.
Automated windows are deemed adequately protected if they:
are installed at a height of >2.5 m; or:
200 mm and a closing speed of <15 mm/s; or:
are part of a smoke and heat evacuation system for emergency use only.
In any case, moving parts of windows that could fall below 2.5 m following breakage of a
system component need to be fixed or secured in
order to prevent them from suddenly
falling or collapsing: e.g. the use of safety arms on bottom
-
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience
allow children to play with the fixed controls and keep any remote
The actuator is destined exclusively for installation indoors. For any special
application we recommend you consult the manufacturer
After removing packaging, check for any damage on the appliance.
Always request exclusive use of original spare parts. Failure to respect this condition
could compromise safety and invalidate the benefits contained in the warranty for the
In the event of any problems or queries, consult your agent or contact the
TO ENSURE
ER SAFETY
.
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard
103 (Particular requirements for drives for gates, doors and windows) and
other directives and regulations indicated in the attached Declarations of Incor
poration and
CE Conformity (at the end of the manual). According to the Machinery Directive, actuators
are “partly completed machinery” intended for incorporation into doors and windows. The
esponsibility, to ensure the
compliance of the entire system with the applicable standards and to issue CE certification.
We strongly discourage any use of the actuators other than that specified and therefore, in
For systems installed at a height of less than 2.5 m above floor level or other levels
accessible to users, the manufacturer/supplier of the window must conduct
risk analysis
regarding potential harm (violent blows, crushing, wounds) caused to people by normal use
or possible malfunction or accidental breakage of the automated windows, and to
in view of these. Such measures include those
controlling the actuators via a “deadman’s button” placed near the system and within
the operator’s field of view, to ensure that people are out of the way during operation.
m and operated by key if accessible to the
use of contact safety systems (also included in the actuators) that ensure a maximum
closing force of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of
200 mm and a closing speed of <15 mm/s; or:
are part of a smoke and heat evacuation system for emergency use only.
In any case, moving parts of windows that could fall below 2.5 m following breakage of a
order to prevent them from suddenly
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience
and knowledge. Do not
allow children to play with the fixed controls and keep any remote
-control units out of
The actuator is destined exclusively for installation indoors. For any special
After removing packaging, check for any damage on the appliance.
Always request exclusive use of original spare parts. Failure to respect this condition
could compromise safety and invalidate the benefits contained in the warranty for the
In the event of any problems or queries, consult your agent or contact the
