nekos
products have been manufactured in accordance with safety standards and
conforms to the stipulations of current standards in force.
When correctly assembled, installed and used according to the present instructions, they
will not generate any danger for persons, animals or items.
Symbols used in the manual
DANGER
Contents
1. SECURITY RULES
................................
2.
TECHNICAL INFORMATION FOR APPLICATION AND OPERATION
3. TECHNICAL DATA
................................
4.
CONSTRUCTION AND REGULATORY REFERENCES
5.
ID PLATE AND MARKING DATA
6.
7. SETTING THE DIP-
8.
8.1.
Preparation of actuator for assembly
8.2. Installation
................................
8.2.1.
Milling of the seats for recessed assembly
8.2.2.
8.2.3.
Drilling for external assembly
8.2.4. External assembly
................................
9.
10. START-UP OPERATIONS
................................
10.1. With actuator
................................
10.2. Without actuator (test)
................................
11.
12.
EMERGENCY OPERATIONS OR MALFUNCTIONS
12.1. Emergency operations
................................
12.2.
Malfunctions of the device
12.3. LED Light signals
................................
13.
14.
15.
DECLARATION OF INCORPORATION (for a partly completed machine) AND EC
DECLARATION OF CONFORMITY
3
products have been manufactured in accordance with safety standards and
conforms to the stipulations of current standards in force.
When correctly assembled, installed and used according to the present instructions, they
will not generate any danger for persons, animals or items.
Symbols used in the manual
This indication draw the attention about potential dangers for
health of peoples and animals.
................................
................................
................................
TECHNICAL INFORMATION FOR APPLICATION AND OPERATION
................................
................................
................................
CONSTRUCTION AND REGULATORY REFERENCES
................................
ID PLATE AND MARKING DATA
................................
................................
................................
................................
–
Selecting the stroke and setting the operating mode
................................
................................
Preparation of actuator for assembly
................................
................................
................................
................................
................................
Milling of the seats for recessed assembly
................................
................................
................................
Drilling for external assembly
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
EMERGENCY OPERATIONS OR MALFUNCTIONS
................................
................................
................................
................................
Malfunctions of the device
................................
................................
................................
................................
................................
................................
................................
................................
................................
DECLARATION OF INCORPORATION (for a partly completed machine) AND EC
DECLARATION OF CONFORMITY
................................
................................
products have been manufactured in accordance with safety standards and
When correctly assembled, installed and used according to the present instructions, they
This indication draw the attention about potential dangers for
safety and
................................
.................... 4
TECHNICAL INFORMATION FOR APPLICATION AND OPERATION
..................................... 5
................................
.................... 5
................................
.......................... 5
................................
.............................. 6
................................
................................... 7
Selecting the stroke and setting the operating mode
.......... 7
................................
................................... 8
................................
................... 8
................................
............................ 9
................................
................................. 9
................................
.................................... 9
................................
.................... 10
................................
..... 10
................................
................................. 10
................................
..... 11
................................
.................. 11
................................
..... 12
................................
............................. 12
................................
.............................. 12
................................
.... 12
................................
............................... 12
................................
............ 13
................................
......................... 14
................................
............................ 14
DECLARATION OF INCORPORATION (for a partly completed machine) AND EC
................................
...................... 15
1. SECURITY RULES
C
PERSONAL SAFETY
.
I
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard
IEC 60335-2-
103 (Particular requirements for drives for gates, doors and windows) and other
directives and regulations indicated in the attached Declarations of Incor
Conformity (at the end of the manual). According to the Machinery Directive, actuators are
“partly completed machinery” intended for incorporation into doors and windows. The
manufacturer/supplier of the window is required, with exclusive r
compliance of the entire system with the applicable standards and to issue CE certification.
We strongly discourage any use of the actuators other than that specified and therefore, in
any case, the supplier of the complete sys
For systems installed at a height of less than 2.5 m above floor level or other levels
accessible to users, the manufacturer/supplier of the window must conduct
regarding potential harm (violent blows, crushing, w
or possible malfunction or accidental breakage of the automated windows, and to implement
suitable protective measures
in view of these. Such measures include those recommended
by the specified standard:
- controlling th
e actuators via a “deadman’s button” placed near the system and within the
operator’s field of view, to ensure that people are out of the way during operation. The
button must be placed at a height of 1.5 m and operated by key if accessible to the
public; or:
-
use of contact safety systems (also included in the actuators) that ensure a maximum
closing force of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of
IEC 60335-2-103; or:
- use of non-
contact safety systems (lasers, light grids); or:
-
use of fixed safety barriers that prevent access to moving parts.
Automated windows are deemed adequately protected if they:
-
are installed at a height of >2.5 m; or:
- have a leading-
edge opening of <200 mm and a closing speed of <15 mm/s; or:
- are pa
rt of a smoke and heat evacuation system for emergency use only.
In any case, moving parts of windows that could fall below 2.5 m following breakage of a
system component need to be fixed or
falling or collapsing
: e.g. the use of safety arms on bottom
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience and knowledge. Do not
allow children to play
with the fixed controls and keep any remote
their reach.
The actuator is destined exclusively for installation indoors. For any special
application we recommend you consult the manufacturer beforehand.
After removing packaging, check f
Always request exclusive use of original spare parts. Failure to respect this
condition could compromise safety and invalidate the benefits contained in the
warranty for the appliance.
In the event of any problems or queries
manufacturer directly.
4
THE FOLLOWING INSTAL
SIS AND PROTECTION MEASURES
.
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard
103 (Particular requirements for drives for gates, doors and windows) and other
directives and regulations indicated in the attached Declarations of Incor
Conformity (at the end of the manual). According to the Machinery Directive, actuators are
“partly completed machinery” intended for incorporation into doors and windows. The
manufacturer/supplier of the window is required, with exclusive r
esponsibility, to ensure the
compliance of the entire system with the applicable standards and to issue CE certification.
We strongly discourage any use of the actuators other than that specified and therefore, in
any case, the supplier of the complete sys
tem retains full liability.
For systems installed at a height of less than 2.5 m above floor level or other levels
accessible to users, the manufacturer/supplier of the window must conduct
regarding potential harm (violent blows, crushing, w
ounds) caused to people by normal use
or possible malfunction or accidental breakage of the automated windows, and to implement
in view of these. Such measures include those recommended
e actuators via a “deadman’s button” placed near the system and within the
operator’s field of view, to ensure that people are out of the way during operation. The
button must be placed at a height of 1.5 m and operated by key if accessible to the
use of contact safety systems (also included in the actuators) that ensure a maximum
closing force of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of
contact safety systems (lasers, light grids); or:
use of fixed safety barriers that prevent access to moving parts.
Automated windows are deemed adequately protected if they:
are installed at a height of >2.5 m; or:
edge opening of <200 mm and a closing speed of <15 mm/s; or:
rt of a smoke and heat evacuation system for emergency use only.
In any case, moving parts of windows that could fall below 2.5 m following breakage of a
system component need to be fixed or
secured in order to prevent them from suddenly
: e.g. the use of safety arms on bottom
-
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience and knowledge. Do not
with the fixed controls and keep any remote
The actuator is destined exclusively for installation indoors. For any special
application we recommend you consult the manufacturer beforehand.
After removing packaging, check f
or any damage on the appliance.
Always request exclusive use of original spare parts. Failure to respect this
condition could compromise safety and invalidate the benefits contained in the
warranty for the appliance.
In the event of any problems or queries
, consult your agent or contact the
TO ENSURE
ER SAFETY
.
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard
103 (Particular requirements for drives for gates, doors and windows) and other
directives and regulations indicated in the attached Declarations of Incor
poration and CE
Conformity (at the end of the manual). According to the Machinery Directive, actuators are
“partly completed machinery” intended for incorporation into doors and windows. The
esponsibility, to ensure the
compliance of the entire system with the applicable standards and to issue CE certification.
We strongly discourage any use of the actuators other than that specified and therefore, in
For systems installed at a height of less than 2.5 m above floor level or other levels
accessible to users, the manufacturer/supplier of the window must conduct
risk analysis
ounds) caused to people by normal use
or possible malfunction or accidental breakage of the automated windows, and to implement
in view of these. Such measures include those recommended
e actuators via a “deadman’s button” placed near the system and within the
operator’s field of view, to ensure that people are out of the way during operation. The
button must be placed at a height of 1.5 m and operated by key if accessible to the
use of contact safety systems (also included in the actuators) that ensure a maximum
closing force of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of
edge opening of <200 mm and a closing speed of <15 mm/s; or:
rt of a smoke and heat evacuation system for emergency use only.
In any case, moving parts of windows that could fall below 2.5 m following breakage of a
secured in order to prevent them from suddenly
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience and knowledge. Do not
with the fixed controls and keep any remote
-control units out of
The actuator is destined exclusively for installation indoors. For any special
application we recommend you consult the manufacturer beforehand.
or any damage on the appliance.
Always request exclusive use of original spare parts. Failure to respect this
condition could compromise safety and invalidate the benefits contained in the
, consult your agent or contact the
