Nemalux AR10 Guida

APPLICATION

AR luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt,

corrosion, vibration and rough usage. This luminaire is certied by NSF for use in Splash-zone and

Non-Food areas of food processing locations as dened in NSF-2. The AR luminaire has been certied for

use on marine vessels inside, outside, and in other severely wet saltwater environments.

Certied to: UL 1598, UL 1598A, and UL 8750;

CSA 22.2 No. 250.0 and CSA22.2 No. 250.13

ABS Listed

Housing: Copper-free Cast Aluminium with Polycarbonate lens

Input Voltage: Based on luminaire sux in table below: Sux - AC: 120-277 VAC | Sux - HV: 347-480 VAC

Electrical Ratings:

Connections: 2 x 3/4” NPT Conduit | Black: Line | White: Neutral | Green: Ground

Optional: Purple: 0-10V Dimming (+) | Grey: 0-10V Dimming (-)

For connections use wire rated to a minimum of 90°C. Class 1 Wiring only.

Dimming control wires must be rated 300V minimum for luminaires with sux AC,

600V minimum for luminaires with sux HV.

Temperature Range: AR10, 15, 20, 25 AC Models: -40°C to +55°C

AR10, 15, 20, 25 HV Models: -40°C to +50°C

AR30 AC, HV Optical models: -40°C to +45°C

AR30 AC Flood model: -40°C to +40°C

AR30 HV Flood model: -40°C to +45°C

Ingress Protection: IP66/67 | Suitable For Wet Locations. Marine Outside Type (Salt Water)

SURFACE/CEILING

MOUNTING INSTALLATION

LUMINANCE

AR10

AR15

AR20

AR25

AR30

RATED VOLTAGE

[Volts]

RATED WATTAGE

[Watts]

INPUT

VOLTAGE

120-277

347-480

120-277

347-480

120-277

347-480

120-277

347-480

120-277

347-480

107

129

145

190

187

247

245

312

310

FREQUENCY

[Hz]

50/60

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

E477827

1-4

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

E477827

STEP 1.

Inspect shipping package and contents to ensure no

damage has occurred during shipping.

STEP 2.

Remove 8x M6 hex cap bracket mounting screws from

head and re-install with included Surface/Suspension

Mount Brackets. See diagram for orientation of brack-

ets. Torque M6 bolts to 5 Nm (45 in-lbs).

STEP 3.

A) For surface mounting conguration, mount lumi-

naire in desired ceiling location using 4x 1/4-20 OR 4x

M6 fasteners and washers (Not provided). One mount-

ing hole on each bracket is keyed to allow partial

pre-installation of two fasteners for ease of install.

B) For ceiling mounting congurations, connect 4x

anchors to the 12.7mm (0.5”) holes. Suspension hard-

ware (Not provided) must be rated for a minimum of

180 lbs.

STEP 4.

Open AR Lens with a 7mm socket or wrench and allow

Lens to hang via retention strap.

Note:

Screws are captive fasteners and will remain attached to

the Lens for ease of reinstall and to prevent loss of

fasteners.

5.0in

126mm

5.2in

132mm

21.1in

535mm

22.5in

570mm

0.5in

12.7mm

0.3in

6.8mm

0.5in

12.7mm

0.5in

12.7mm

0.5in

12.7mm

0.5in

12.7mm

SURFACE/CEILING MOUNT INSTALLATION

(Brackets Included as Standard Parts)

Refer to alternate instructions if using Conduit, Hook, Wall, Pole or Yoke Mount

Step 2

Step 3A

Step 3B

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

2-4

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

WARNING

To reduce the risk of electric shock, disconnect the luminaire

from the supply circuit before opening for installation and

servicing. Keep tightly closed when in operation.

WARNING

To avoid the risk of re, explosion, or electric shock, this

product should be installed, inspected, and maintained

by a qualied electrician only, in accordance with all

applicable electrical codes.

STEP 5.

Make wiring connections from branch circuit conductors

to factory provided lead wires. Refer to NEC/CEC codes

and follow all applicable local standards. See wiring

diagram on Page 4.

For 0-10V Analog Dimming Control, connect Violet (+)

and Gray (-) to 0-10VDC control wiring:

• 0-10V Interface can be wired as Class 1 or Class 2

Circuit.

• LED Drivers will source a combined maximum of

400µA for control needs.

• 0-10V Controller must sink current from LED driver

0-10V control connections.

NOTE:

To aid in assembly and protection against ingress use of a

petrolatum or soap thickened mineral oil based thread

lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the

integrity of the enclosure.

STEP 6.

Close AR lens. Ensure the retention cable is not pinched

between AR Head and the AR Lens. Tighten lens bolts

using a 7mm socket or box wrench to 1.7 N-m (15 in-lbs)

in the order designated in the diagram to ensure gasket

sealing.

Step 5

Step 6

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

3-4

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

WIRING DIAGRAM

PS 1

PS 2

GROUND

(Factory)

BLACK  LINE

WHITE  NEUTRAL

GREEN  GROUND

PURPLE  DIM +

GREY  DIM 

BLACK

WHITE

GREEN

PURPLE

GREY

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

4-4

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

AR-PM – POLE MOUNT INSTALLATION

Refer to alternate instructions if using Conduit, Hook, Wall or Yoke Mount

INSTALLATION STEPS

Step 3

Step 5

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire. Remove 4 x M6 bolts from supply side of

luminaire and disard.

STEP 2.

Install the provided plastic 3/4”bushing into side 3/4" NPT entry.

STEP 3.

Install Pole Mount and gasket with adhesive side applied to mount

using included M6 bolts and washers.

Torque to 5 Nm (45 in-lbs)

STEP 4.

Thread luminaire assembly onto 1.5”NPT pole.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or soap

thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of the

enclosure.

STEP 5.

Insert and tension M6 set screw to pole to lock rotation.

STEP 6.

Resume installation instructions provided with luminaire. (STEP 4 in AR

Installation Instructions provided with Luminaire)

SET SCREW

This AR-PM kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

AR-PM

PART NAMEQTY

POLE MOUNT

POLE MOUNT GASKET

M6 X 25mm HEX HEAD CAP SCREW

M6 FLAT WASHER

M6 X 16mm HEX HEAD CAP SCREW

3/4 NPT THREADED SMOOTH BORE BUSHING

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

1-1

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

AR-WM – WALL MOUNT INSTALLATION

Refer to alternate instructions if using Conduit, Hook, Pole or Yoke Mount

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire. Remove 4 x M6 bolts from supply side of

luminaire and disard.

STEP 2.

Install provided 3/4 NPT conduit plugs in desired locations on wall

mount. To maintain ingress rating all NPT entries not used for wiring

connections are required to be plugged. Torque to 10 Nm (88 in-lbs)

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or soap

thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of the

enclosure.

STEP 3.

Install provided 3/4”NPT plastic bushing onto side NPT entry on AR

head, rotate so that ats are parallel to lens surface to avoid

interference with mount hardware.

STEP 4.

Install Wall Mount main body with included M6 bolts and washers and

adhesive backed gasket. Apply gasket to mount with adhesive backed

side. Torque to 5 Nm (45 in-lbs).

STEP 5.

Install Back Cover Plate with 4x M4 Flat head screws and adhesive

backed gasket. Apply gasket with adhesive side applied to mount main

body. Torque to 1.7 N-m (15 in-lbs).

STEP 6.

Mount luminaire assembly to desired location using 4x 1/4-20 OR M6

Screws or Bolts (Not Provided).

STEP 7.

Resume installation instructions provided with luminaire. (STEP 4 in AR

Installation Instructions provided with Luminaire)

Steps 2 through 5

[5.7in]

145mm

4 x

6.8mm THRU ALL

[5.7in]

145mm

Step 6

This AR-WM kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

AR-WM

PART NAMEQTY

WALL MOUNT

WALL MOUNT PLATE

WALL MOUNT PLATE SIDE GASKET

WALL MOUNT GASKET

6 x 25mm SOCKET HEAD CAP SCREW

M4x 10mm FLAT HEAD SOCKET CAP SCREW

M6 FLAT WASHER

3/4 NPT HEX CAP PLUG

3/4 NPT THREADED SMOOTH BORE BUSHING

INSTALLATION STEPS

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

1-1

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

4.3in

108.15mm

2.3in

59mm

0.27in

6.76mm

0.27in

6.8mm

1.7in

44mm

2.8in

70mm

AR-YM – YOKE MOUNT INSTALLATION

Refer to alternate instructions if using Conduit, Hook, Pole or Wall Mount

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire. Remove 4 x M6 bolts from supply side of

luminaire and disard.

STEP 2.

Install suitable wiring system to the conduit opening per CEC/NEC

requirements for the specic location of install.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or soap

thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of the

enclosure.

STEP 3.

Loosely assemble Yoke mount with carriage bolts on inside and

washers and nuts on the outside.

NOTE:

Depending on which mounting hole is used in the curved slot, the luminaire may

be congured for an upward or downward adjustable swing.

STEP 4.

Thread installed wiring through openings in yoke mount cheek plate

and yoke mount bracket. Mount yoke assembly to luminaire using 4x

M6 Socket Head Cap Screws and Washers (Provided). Torque fasteners

to 5 Nm (45 in-lbs).

STEP 5.

Mount luminaire assembly to desired location using 4x 1/4-20 OR M6

Screws or Bolts (Not Provided).

STEP 6.

Adjust and aim luminaire to desired position. Torque hardware nuts to

9 N-m (80 in-lbs).

STEP 7.

Resume installation instructions provided with luminaire. (STEP 4 in AR

Installation Instructions provided with Luminaire)

Step 5

Step 3

This AR-YM kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

INSTALLATION STEPS

AR-YM

PART NAMEQTY

YOKE MOUNT A

YOKE MOUNT B

CHEEK PLATE

1/4-20 HEX NUT

1/4" FLAT WASHER

1/4-20 x 0.5in CARRIAGE BOLT

M6 x 25mm HEX HEAD CAP SCREW

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

1-1

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

AR-HK – HOOK PENDANT INSTALLATION

Refer to alternate instructions if using Pendant, Wall, Pole or Yoke Mount

Step 3

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire.

STEP 2.

It is recommended to install Secondary Safety Cable by looping

appropriate steel cable or chain through the outer band of the unit and

fastening a closed loop. Secondary safety hardware must be rated for a

minimum of 180lbs. Secondary safety cables made from stainless steel

aircraft cable are available upon request.

STEP 3.

Slide anti-rotation lock onto suspension hook assembly and install hook

assembly into ¾ NPT threaded entry. Tighten to hand tight plus 1 to 2

turns. Slide anti-rotation lock into place and tighten set screw to lock

unit in place.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or soap

thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of the

enclosure.

STEP 4.

Latch hook onto eye-bolt or other xed mounting loop. Mounting point

must be rated for a minimum of 180lbs.

STEP 5.

Install remaining loop of secondary safety chain or steel cable to

suitable mounting location and fasten securely.

STEP 6.

Resume installation instructions provided with luminaire. (STEP 4 in AR

Installation Instructions provided with Luminaire)

Step 2

This AR-HK kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

INSTALLATION STEPS

AR-HK

PART NAME

QTY

PENDANT HOOK ASSEMBLY

ANTI-ROTATION ASSEMBLY

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

1-1

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

This kit contains NSF component Anti-Rotation-Lock

(1004-01-02-201)

AR-CM –

CONDUIT MOUNT INSTALLATION

Refer to alternate instructions if using Wall, Hook, Pole or Yoke Mount

Step 2

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire.

STEP 2.

Slide anti-rotation lock onto suitably mounted hanging conduit or

luminaire hanger and install luminaire onto ¾”NPT threaded nipple.

Tighten to hand tight contact plus 1 to 2 turns. Slide anti-rotation lock

into place and tighten set screw to lock unit in place. Fixed Rigid Metal

Conduit must be suitably mounted to prevent rotation and system

must be rated for 180 lbs.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or soap

thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of the

enclosure.

STEP 3.

Install Secondary Safety Cable by looping appropriate steel cable or

chain through the outer band of the unit and fastening a closed loop.

Secondary safety hardware must be rated for a minimum of 180lbs.

Install remaining loop of secondary safety chain or steel cable to

suitable mounting location and fasten securely. Secondary safety

hardware must be rated for 180lbs.

STEP 4.

Resume installation instructions provided with luminaire. (STEP 4 in AR

Installation Instructions provided with Luminaire)

Step 3

This AR-CM kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

INSTALLATION STEPS

AR-CM

PART NAMEQTY

1ANTI-ROTATION BRACKET ASSEMBLY

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

1-1

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

This kit contains NSF component Anti-Rotation-Lock

(1004-01-02-201)

AR-YK – HIGH VIBRATION YOKE INSTALLATION

Refer to alternate instructions if using Conduit, Hook, Pole, Wall Mount, or Yoke Mount

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire. Remove 8 x M6 hex bolts from sides of

luminaire and discard.

STEP 2.

Mount AR high vibration yoke to mounting surface using a minimum of

4x ¼-20 or M6 fasteners (not provided).

STEP 3.

Install suitable wiring system to the conduit opening per CEC/NEC

requirements for the speci-c location of install.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or soap

thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of the

enclosure.

STEP 4.

Mount AR Cheek Plates to sides of AR luminaire using 4x M6 at head

cap screws per side. Thread one cheek plate over installed wiring

during assembly. Torque fasteners to 5 Nm (45 in-lbs).

STEP 5.

Thread installed wiring through opening in AR high vibration yoke

mount and install AR luminaire into yoke. The raised circular bosses on

the AR cheek plates should register inside of the large circular holes on

the AR high vibration yoke mount arms. Rotate luminaire to aim in the

desired direction and fasten in place using 2x M6 socket head cap

screws and at washers per side. Torque fasteners to 5 Nm (45 in-lbs).

STEP 6.

Resume installation instructions provided with luminaire. (STEP 4 in AR

Installation Instructions provided with Luminaire)

Step 4

Step 2

This AR-YK kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

INSTALLATION STEPS

AR-YK

PART NAMEQTY

AR HIGH VIBRATION YOKE

CHEEK PLATE

M6 x 1 x 25mm SOCKET FLAT HEAD CAP SCREW

M6 FLAT WASHER

M6 x 1 x 16mm SOCKET HEAD CAP SCREW

Nemalux

I N DUSTRIAL

AR-GEN

rev. A-17

1-1

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

WARNING:

The AR Head must not face upwards

by any degree beyond the vertical

position for Class II, Division 2, Zone 22,

and Class III hazardous locations.

✔

✘

LIGHT BEAM

HORIZON

[3.1in]

80mm

[17.3in]

440mm

[4.3in]

108mm

[2.3in]

59mm

[1.7in]

44mm

10 x 6.8mm [0.27in] THRU ALL

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Nemalux Lanterna

Nemalux

Nemalux MR3 Manuale utente

Nemalux

Nemalux XR-HAZ Manuale utente

Nemalux

Nemalux XR8 Manuale utente

Nemalux

Nemalux GS Series Manuale utente

Nemalux

Nemalux GS Series Manuale utente

Manuali Lanterna popolari di altre marche

KYOWA

KYOWA KW-9114 Manuale utente

Stahl

Stahl ECOLUX 6610 Series Manuale utente

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuale utente

PRG

PRG VARI LITE VL5 Manuale utente

Raytec

Raytec VARIO2 series Manuale utente

ENSA

ENSA LEDBT18WS2 Manuale utente

LUG

LUG OFFICE LB LED N/T Manuale utente

GE Wallighter 250 Manuale utente

Draper

Draper RLEDL19/B Manuale utente

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuale utente

Panasonic

Panasonic EY3741B57 Manuale utente

Clas Ohlson

Clas Ohlson LCC8T Manuale utente

Coolon

Coolon WDN-140 Manuale utente

Holiday Travel

Holiday Travel 834873 Manuale utente

BEGA

BEGA 84 036 Manuale utente

BEGA

BEGA 33 596 Manuale utente

Dale Tiffany

Dale Tiffany GT701162 Manuale utente

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuale utente