Nemtek WIZORD 2 Guida utente

WIZORD 2

Electric Fence Energizer

Installer Manual

Introduction & Disclaimer 3

Nemtek group outlets 4

Mounting & Battery Replacement 5

Connection to the Fence 6

Connections/Configuration Diagram 7

PC Board Replacement Procedures 8

Service Conditions 9

Appendix 10

Installation notes 13

IEC Safety Information 14

Document revision history 14

Table of Contents

INTRODUCTION

The WIZORD 2 is a battery (12V 7AH nominal) operated energizer suitable for connection to

mains (220-240Vac, 50-60Hz).

The batteries to be used are rechargeable lead-acid batteries. Non-rechargeable batteries must

not be used. The lead-acid batteries require venting and it is imperative that the energizer be

situated in a well-ventilated area.

A new fully charged battery will typically provide in excess of 24 hours backup. Backup time will

vary with fence condition though.

Electric fencing can be lethal. Please avoid entanglement\entrapment hazards (See APPENDIX

at the end of this manual) and warn the user to avoid head contact with the fence.

DISCLAIMER

NEMTEK Holdings (Pty) Ltd or any of its subsidiary companies does not guarantee that the

operation of the product will be uninterrupted or totally error free.

Energizer specifications may be altered without prior notification.

The installer is referred to the definitions and general requirements in the Appendix.

The installer must take into consideration the applicable municipal laws concerning the

installation of electric fences. General guidelines are available, or refer to the website:

http://www.nemtek.com. International standards can be viewed at http://www.iec.ch and

South African standards on http://www.sabs.co.za.

Introduction & Disclaimer

HEAD OFFICE

Tel: +27 (0)11 462 8283 Northriding Commercial Park

Fax: +27 (0)11 462 7132 Stand 251, Aintree Street, Northriding

Randburg, South Africa

EXPORTS

Tel: +27 (0)11 462 8283 exports@nemtek.com

Fax: +27 (0)11 462 7132

EDENVALE

Tel: +27 (0)11 453 1970 Unit 4, Meadowdale Park

Fax: +27 (0)11 453 1858 Cnr. Dick Kemp & Herman Roads

Meadowdale, Edenvale, South Africa

CAPE TOWN

Tel: +27 (0)21 386-3742 27B Concord Crescent, Airport City

Fax: +27 (0)21 386-5573 Cape Town, South Africa

NELSPRUIT

Tel: +27 (0)13 752-2187 Waterval Ave, Riverside Industrial

Fax: +27 (0)13 752-2188 Nelspruit, South Africa

KWAZULU-NATAL

Tel: +27 (0)31 701-2125 19 Henwood Road

Fax: +27 (0)31 701-2125 Pinetown, South Africa

AUSTRALIA

Tel: (08) 9303 9855 Unit 5, 19 Innovation Circuit,

Email: nemtek@bigpond.net.au Wangara, 6065, Perth, WA, Australia

Website: www.nemtek.com

E-mail: nemtek@nemtek.com

Manufactured in South Africa

NEMTEK Group Outlets

Mounting & Battery Replacement

STEP 1: Disconnect mains. Open the lid after

removing the two cap screws. Unplug the

battery terminals if connected.

STEP 2: Remove screws and battery bracket

STEP 3: Remove battery

*Dispose of old battery according to legal

requirements. Do not replace with a non-

rechargeable battery!

STEP 4: Use a drilling template and drill 4 x

8mm holes in the wall for mounting the unit.

Four nail-in anchors are supplied with the unit.

Insert the plastic sleeve of the nail in anchor

into the wall then hammer the screw in with a

screwdriver and hammer.

NB: Always insert the plastic sleeve from

the inside of the box.

STEP 5: Insert battery with the positive

terminal to the top.

STEP 6: Place the battery bracket back

(with plastic offsets at the top) and fasten

the screws into place.

STEP 7: Connect battery wires. Close the lid

by hooking the top of the lid in first and then

fasten the bottom down with the two cap

screws. Apply mains power to the unit.

Note: Energizer to be mounted vertically against a

flat surface, in a well ventilated area.

Avoid prolonged exposure to direct sunlight.

OPTION 1: NO EARTH LOOP MONITORING

Bridge the earth OUT terminal to earth RETURN terminal.

Connection to the Fence

Earth spikes as per

SANS 10222-3 or local

specifications

OPTION 2: EARTH LOOP MONITORING; GOOD SOIL EARTHING

This earth wire is not

coupled to the fence

earth at any other point

OPTION 3: EARTH LOOP MONITORING; POOR SOIL EARTHING

Earth wire connection

Live wire connection

Earth wire connection

Live wire connection

Earth wire connection

Live wire connection

Earth spikes as per SANS 10222-3

or local specifications

Connection/Configuration Diagram

*JP4 – Bypass Safety Switch. Not to be installed during normal use.

All other Jumpers are reserved for factory use only

JUMPER OPERATION:

Function

JP1

JP2

JP3

Energizer Operation

Gate Alarm

out

Switched Input delayed for 4 minutes with

energizer On only

Gate Alarm

out

Switched Input delayed for 1 minute with

energizer On only

Panic Alarm

out

Switched Input instantaneous (panic alarm)

with energizer On or Off

High/Low

Voltage Mode

out

Switched Input toggles the energizer between

High Voltage and Low Voltage mode

Remote On/Off

out

Switched Input acts as remote On\Off switch

Remote On/Off

indication and

Gate alarm

out

Strobe indicates fence is On or Off, Switched

Input delayed for 4 minutes with energizer On

only

Not yet available

out

Service Alarm disabled, Switch Input delayed

for 4 minutes with energizer On only

Reserved for factory use

PC Board Replacement Procedures

REMOVAL

STEP 1: Disconnect mains power and the

battery terminals if connected.

STEP 2: Remove screws.

STEP 3: Remove all connectors

from PC Board.

STEP 4: Gently pull PC Board

vertically upwards to remove (connections

are on the back side of the PC Board).

REPLACEMENT

STEP 5: Gently push PC Board back into

place. Take care that the spade connectors

are correctly positioned before pushing the

PC Board into place. Also ensure that the

opto-coupler (looks like LED) is correctly

positioned before pushing the PC Board

into place.

STEP 6: Reconnect all connectors to the PC

Board.

STEP 8: Reconnect the battery terminals

and apply mains power.

Service Conditions

HOW TO CHECK: (ALL FUSES ARE 2 AMPERE FAST BLOW)

SUPPLY: The power LED does not illuminate when the mains power is present

AUX:The siren and strobe does not function

BATTERY:The energizer switches off in the absence of mains power

FUSE DESCRIPTION & FAULT SYMPTOMS

SUPPLY

BATTERY

AUX

Basic definitions

• Electric Fence:

A barrier which includes one or more electric conductors, insulated from earth, to

which electric pulses are applied by an energizer

• Connecting Lead:

An electric conductor, used to connect the energizer to the electric fence or the

earth electrode

• Electric Security Fence:

A fence used for security purposes which comprises an electric fence and a physical

barrier electrically isolated from the electric fence

• Public Access Area:

Any area where persons are protected from inadvertent contact with pulsed

conductors by a physical barrier

• Pulsed Conductors:

Conductors which are subjected to high voltage pulses by the energizer

• Secure Area:

An area where a person is not separated from pulse conductors below 1,5m by a

physical barrier

General requirements for electric security fences

Electric fences shall be installed and operated so that they cause no electrical hazard to

persons, animals or their surroundings.

Electric fence constructions which are likely to lead to the entanglement of animals or

persons shall be avoided, as entrapment can be lethal.

An electric fence shall not be supplied from two different energizers or from independent

fence circuits of the same energizer.

For any two different electric fences, each supplied from a different energizer with

independent timing, the distance between the wires of the two electric fences shall be at

least 2.5m. If this gap is to be closed, this shall be affected by means of electrically non-

conductive material or an isolated metal barrier.

Barbed wire or razor wire shall not be electrified by an energizer.

Appendix

Indice

Altri manuali Nemtek Alimentazione elettrica

Nemtek

Nemtek druid LCD Guida utente

Nemtek

Nemtek AGRI Solar Manuale utente

Nemtek

Nemtek MERLIN II M Series Manuale utente

Nemtek

Nemtek WIZORD Manuale utente

Nemtek

Nemtek AGRI 80 Manuale utente

Nemtek

Nemtek MERLIN M25 Manuale utente

Nemtek

Nemtek MERLIN STEALTH MASTER Manuale utente

Nemtek

Nemtek WIZORD 4 Manuale utente

Nemtek

Nemtek AGRI xJ Manuale utente

Nemtek

Nemtek Druid 28LCD Manuale utente

Nemtek

Nemtek druid LCD Manuale utente

Nemtek

Nemtek MERLIN 4 Manuale utente

Nemtek

Nemtek MERLIN STEALTH MASTER Guida utente

Nemtek

Nemtek druid LCD Guida utente

Nemtek

Nemtek MERLIN 4 Guida utente

Nemtek

Nemtek Strainrite AGRI Solar Manuale utente

Nemtek

Nemtek MERLIN STEALTH M113S Manuale utente

Nemtek

Nemtek Druid LCD 2X Istruzioni di installazione e manutenzione

Nemtek

Nemtek MERLIN STEALTH MASTER Guida utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente