NEO C-R200 Manuale utente
SMART CONTROLLER
powered by Neo Smart Blinds
ENGLISH
SETUP CODE
CODE DE CONFIGURATION
MODEL/MODÈLE: C-R200
System requirements
• A strong WiFi signal (3 bars or more) in the location where you
will setup your Smart Controller.
• The Smart Controller only supports 2.4GHz WiFi (IEEE 802
11b/g/n), not 5GHz. WiFi security needs to be set to WPA-PSK or
WPA2-PSK.
• A smartphone or tablet running Android 4.4 (KitKat) or higher,
or iOS 8 or higher is needed.
Troubleshooting
The home WiFi doesn’t appear in the step 4
Try rescanning, if the problem persists, you will need to reposition
the Smart Controller to a place with stronger WiFi signal. In this
case, exit the process (tap on the menu, then tap Your Rooms),
replace the Smart Controller and start over.
The Smart Controller LED in the bottom is not blinking blue
The process fails in the last step
Press the S button for 10 seconds, then press the R button once
and start over. Pay special attention when typing the WiFi
password.
Need more help?
Visit neosmartblinds.com/smartcontroller for detailed instructions
about how to use the app and troubleshooting.
Integrations
Smart home devices
Visit neosmartblinds.com/smartcontroller-integrations for detailed
information about connecting to smart home devices, such as
Amazon Alexa.
Control4
Please send an email to tech@neosmartblinds.com with your
name, your email and your company’s name. This information is
necessary to always send to you any further driver update.
Legal Information
Getting to know your
Smart Controller
Smart Controller Status:
Flashing blue - Hotspot available
Flashing green - Connecting to the WiFi network
Pulsing cyan/blue-green - Connected to the Internet
Getting Started
Download the Neo Smart Blinds app
Download the app to your phone or tablet by
searching Neo Smart Blinds on Google Play
or the App Store.
Note: Do not install Neo Smart Blinds Blue
Plug in your Smart Controller in reach of your home WiFi
Choose a place not too far from your home router or a place
you know has good WiFi signal strength. You will be able to
change its location after, if necessary.
Create an account and choose the setup code written
on the cover
After opening the app, tap on Create one to create
a new account. Enter a valid email address and choose
a password, select the region time zone from the place
where the Smart Controller will be located. Choose the
setup code written in the cover and tap on Register.
Follow the app step by step to add the Smart Controller
Have in hand the home WiFi password. It will be necessary
to connect the Smart Controller to the Internet.
Note: Some Android users won’t be connected quickly to the
hotspot. If it is the case, please wait about 10 seconds
before returning to the app. During this time, your device may
notify you that the hotspot does not have Internet access,
and will prompt you whether you want to remain connect-
ed. You need to select the option that will allow you to keep
connected before returning to the app.
micro-USB port
power adapter
micro-USB cable
LED indicator
Smart Controller Status
Reset button
Setup button
FCC ID: 2ALM6-CR2P1A
Warning: Changes or modications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment. This device complies with Part 15 of
the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help
IC: 22561-CR2P1A
This device complies with Industry Canada’s licence-ex-
empt RSSs. Operation is subject to the following two
conditions:
• This device may not cause interference; and
• This device must accept any interference, including
interference that may cause undesired operation of
the device.
This device meets the exemption from the routine
evaluation limits in section 2.5 of RSS102 and users
can obtain Canadian information on RF exposure and
compliance.
This end equipment should be installed and operated
with a minimum distance of 20 centimeters between the
radiator and your
NEOV1
SMART CONTROLLER
propulsé par Neo Smart Blinds
FRANÇAIS
Code de conguration
tiise e code de conguration crit sur tiuette
au dos de cette age
Conguration générale requise
• n signa ii asse uissant andes ou us endroit o
ous ae instaer aarei mart Controer
• e mart Controer soutien ue a ruence du ii de
et non
• n thone inteigent ou une taette dot de a ersion
ndroid itat ou us rcent ou ien i ou us rcent
Résoudre des problèmes
Le réseau Wi domestique n’apparaît pas sur le pas 4
ssae rescanner si e rome ersiste ous dere
reositionner e mart Controer dans un endroit aec un signa
ii us ort ans ce cas uitte e rocessus tae sur e
menu uis aue sur our ooms reositionne e mart
Controer et recommence
La lumière DEL en bas du Smart Controller ne clignote pas
en blue
Le processus échoue à la dernière étape
ue sur e outon endant secondes uis aue une
ois sur e outon et recommence aites attention orsue
ous tae e mot de asse ii
Besoin d’aide?
Visitez neosmartblinds.com/smartcontroller our otenir des
instructions dtaies sur utiisation de aication et
a rsoution des romes
Intégrations
Appareils domestiques intelligents
Visitez neosmartblinds.com/smartcontroller-integrations our
otenir des inormations dtaies sur a conneion des
aareis domestiues inteigents tes ue maon ea
Control4
euie enoer un courrie techneosmartindscom aec
otre nom otre courrie et e nom de otre entrerise Cette
inormation est ncessaire our touours ous enoer toute
nouee mise our du iote
Information légale
IC: 22561-CR2P1A
e rsent aarei est conorme au C dndustrie Canada aicaes au aareis radio
eemts de icence eoitation est autorise au deu conditions suiantes
• aarei ne doit as roduire de rouiage
• utiisateur de aarei doit acceter tout rouiage radioectriue sui mme si
e rouiage est suscetie den comromettre e onctionnement
e disositi rond eemtion des imites dauation de routine dans a section de
et es utiisateurs euent otenir des renseignements canadiens sur eosition au et
e resect
Cet uiement derait tre insta et actionn aec une distance minimum de centimtres
entre e radiateur et otre cors
Description de votre
Smart Controller
État du Smart Controller:
eu cignotant otsot disonie
ert cignotant en train de se connecter au rseau ii
Canueert usant Connect nternet
Démarrage Rapide
Téléchargez l’appli Neo Smart Blinds sur votre
appareil mobile
charge ai sur otre aarei moie en
aisant une recherche our Neo Smart Blinds
sur ooge a ou sur tore
Note: e as instaer ai eo mart inds ue
Branchez votre Smart Controller assez proche à votre
WiFi
Choisisse un endroit as tro oin de otre routeur
domestiue ou un endroit ue ous sae ui a une onne
orce de signa ii ous ourre e reositionner ars
si ncessaire
Créez un compte et choisissez le code de conguration
écrit sur la couverture
rs ourir ai touche sur Crer our crer un
noueau comte ntre une adresse courrie aide
choisisse un mot de asse et sectionne e useau horaire
de a rgion o se troue e mart Controer Choisisse e
code de conguration crit sur a couerture et touche
sur nregistrer
Suivez les instructions dans l’appli
e en main e mot de asse de otre ii domestiue
sera ncessaire our connecter e mart Controer
otre nternet
Note: Certains utiisateurs ndroid ne seront as connects
raidement au oint daccs du mart Controer i cest e cas
attende eniron secondes aant de retourner ai e
aarei moie eut ous inormer ue e oint daccs ne disose
as dun accs nternet et ous demande si ous souhaite rester
connect ous dee sectionner otion ui ous ermettra de
rester connect aant de retourner ai
ort micro
datateur
daimentation
Ce micro
umire indicatrice
tat du mart Controer
outon de rinitiaisation
outon de conguration
Altri manuali NEO Controllori
