NEO Argento esee Istruzioni per l'installazione

ASSEMBLY, OPERATION

& MAINTENANCE INSTRUCTIONS

NEO ARGENTO ESEE, FIGURA ESEE & CURVA ESEE

FOR OUTDOOR USE ONLY

here barbecuing meets art

ASSEMBLY, OPERATION AND MAINTENANCE INSTRUCTIONS

FOR EVERDURE 4 BURNER GAS BARBECUE RANGE

ARGENTO ESEE, FIGURA ESEE AND CURVA ESEE OUTDOOR BARBECUES

CONTENTS

SECTION PAGENO.

General Safety Instructions 3

Appliance Details 4

Gas Connections 4

OutdoorInstallationGuide 5

Operating Instructions for Barbecue 6

Lighting Procedure 6

Cooking 7

Cleaning&Storage 7

Operating Instructions for Wok Burner 8

Esee Light System Instructions 8

Troubleshooting 9

Maintenance 9

Assembly Instructions 10-17

It is important that you retain these instructions for future reference.

Neo Argento Esee Neo Figura Esee

IMPORTANT SAFETY INSTRUCTIONS (GAS)

IMPORTANT: Read the assembly instruction section and safety precautions of this booklet carefully

before removing the contents of this carton.

1. This barbecue and wok burner is for OUTDOOR USE ONLY. This appliance must NOT be used indoors.

2. Unsupervised children or pets should not be near a barbecue while cooking or during warm up or cool down.

Ensure children or pets are kept a distance well away from the barbecue whilst it is in use. Ensure that young

children do not play with the appliance.

3. Particular care must be taken when removing the fat tray. Hot fats can cause serious injury.

4. Turn all gas valves off including cylinder after use. Do not allow build up of unburned gas.

5. Do not use this appliance for any purpose other than what it is intended for.

6. Do not move this barbecue while in use as accessible parts may be very hot.

7. People with flammable clothing such as nylon etc. should keep well away from the barbecue when it is

operating.

8. Never leave burners on high for more than 10 minutes unless actually cooking.

9. Always check for leaks when a gas cylinder is replaced or reconnected.

10. Sand, kitty litter and fat absorbers should not be used in the fat tray.

11. In case of fat fire turn cylinder off. Fat drip trays should be cleaned and checked before using the barbecue.

Regular cleaning should reduce the build up of fat and food residues which is combustible and can result in a fat

fire. Fat fires can be prevented with diligence in cleaning your fat tray. Damage as a result of fat fire is not

covered by your warranty and voids it.

12. For your safety and enjoyment, read all operating instructions before lighting.

13. Ensure that the product has adequate clearance from combustible materials. The appliance is designed so that

heat will not affect the trolley. All combustible materials must be kept more than 250mm from the sides of the trolley

and more than 1500mm above the cooking surface of the barbecue.

14. If the burner makes a hissing sound when lit, it may be burning inside. Turn the burner off, allow to cool, and try

ignition again. Keep your barbecue protected against strong wind – if this cannot be avoided, always check that the

burners remain alight if operating the barbecue in windy conditions.

15. This appliance is not intended for use by young children or infirm persons.

16. When the wok burner is in use or is still hot, the lid must not be placed in the closed position.

17. Do not carry out any servicing on the gas manifold of the barbecue yourself – this must only be done by authorised

technicians.

18. We recommend that you regularly maintain your barbecue and keep it in good condition. This can be achieved by

following the cleaning and maintenance suggestions in this booklet.

DO NOT OPERATE THIS APPLIANCE BEFORE READING THE INSTRUCTION BOOKLET

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE

DO NOT STORE CHEMICALS OR FLAMMABLE MATERIALS OR SPRAY AEROSOLS NEAR THIS APPLIANCE

DO NOT OPERATE THIS APPLIANCE INDOORS

DO NOT ENCLOSE THIS APPLIANCE

IMPORTANT SAFETY INSTRUCTIONS (ELECTRICAL)

IMPORTANT: Read the safety precautions of this booklet carefully before removing the barbecue from

its carton or connecting the barbecue to an electrical supply.

1. Do not immerse any part of the power pack or cables in water. Do not connect or use the lighting system in the rain.

2. The lighting system should be turned off and disconnected from the main power source whenever it is not in use, or

when changing light globes.

3. Only replace globes with those of equivalent wattage (10W, 12Vac). Using higher rated globes could damage the

globe housing, wiring or power pack. Replacement globes are available from Everdure.

4. All electrical cables should be stowed within the barbecue trolley when the barbecue is not in use.

5. The supply cord plug should be removed from the socket-outlet before any cleaning is done.

6. Do not place cord extension sockets or portable power boards where they may be splashed or where moisture may

get in.

7. Check periodically for damage to the supply cord and power pack. Do not use a damaged appliance and do not

attempt to fix any electrical faults. Contact your Service Centre to have any parts replaced with an equivalent unit.

8. This appliance should be maintained in order to ensure a long, useful life and protect the operator against electric

shocks.

9. A safety switch can enhance electrical safety when using this appliance. If in doubt, speak to a local licensed

tradesperson.

APPLIANCE DETAILS

Gas Type: Universal LPG

(Propane and/or Butane gas)

N.G.

Burner Pressure: 2.75 kPa 0.95 kPa

Injector Diameter: Ø1.10 mm Ø1.65 mm

Heat Input: 60 MJ/ hr 50 MJ/ hr

Wok Injector Diameter: Ø0.90 mm Ø1.65 mm

Wok Heat Input: 10.5MJ/hr 12.5MJ/hr

Note: The size of the injector diameter is stamped on one of the hexagon faces (e.g. ‘104’ for Ø1.04mm injector).

Air is admitted at the underside of the front and rear of the combustion chamber. Exhaust gases are emitted

through the grill plate, around the edge of the hot plate and through the louvers in the rear of the hood.

The Esee lighting system requires a 240Vac supply (via a standard Australian socket outlet). The supplied power

pack is rated to IP64, and supplies 12Vac with a maximum output of 20VA. This transformer complies to

Australian Standards AS/NZS 3108 (Safety) and AS/NZS 1044 (EMC).

GAS CONNECTIONS

LOCAL AUTHORITY REQUIREMENTS

Check Gas Type and specifications plate on the left-hand side of the barbecue. All gas fitting work, service and repairs

can only be performed by an authorised person in accordance with AS5601 / AG601 and local gas regulations.

NATURAL GAS

Neo 4 burner barbecues can be converted to use natural gas ONLY with a Neo NG 4 burner conversion kit. Fit the NG

cross-over adaptor, NG manifolds, regulator and NG hose. This conversion can ONLY be performed by an authorised

person in accordance with AS5601 / AG601 and local gas regulations.

Note: The burner pressure (as noted on the appliance details) MUST be checked after installation by turning on and

measuring at the regulator output test point. All connections must be checked for leaks.

FOR GAS CYLINDER CONNECTION

1. To achieve the optimum performance from your Barbecue, an approved gas cylinder (POL fitting) of 9kg capacity

must be used.

2. Do not connect gas to a barbecue that is not secured in a trolley.

3. Connect the cylinder to the barbecue, via the hose and regulator. Firmly tighten joints, but do not over-tighten. Take

care not to damage the regulator fitting.

LEAK TESTING

1. Make sure gas controls are Off and turn the cylinder valve On.

2. Check for leaking joints by brushing with solution of half-liquid detergent and half water. If a leak is present, bubbles

will appear (or you will hear a hissing sound). Retightening connections can generally repair a leaking joint. You must

also check the gas hose and connection at the gas cylinder, and at the wok burner. If a leak cannot be resolved, do

not proceed.

LEAK TEST ALL CONNECTIONS, INCLUDING THE CONNECTION

TO THE GAS CYLINDER.

DO NOT USE NAKED FLAME FOR LOCATING GAS LEAKS.

IF A LEAK PERSISTS CALL AN AUTHORISED GAS FITTER.

LENGTH (mm) WIDTH (mm) HEIGHT (mm)

Barbecue only 830 545 220

Argento Esee & Figura Esee 1540 640 1220

Barbecue

and Trolley Curva Esee 1510 640 1220

Secondary Air Inlet (Front) 15mm x full width of fat tray

Secondary Air Inlet (Rear) 54 x Ø22mm holes

OUTDOOR INSTALLATION GUIDE

This Appliance shall only be used in an above ground open-air situation with natural ventilation, without

stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural

convection.

This appliance must not be used indoors. Do not use your barbecue in garages, porches, sheds or

other enclosed areas. The barbecue is not intended to be installed in or used on recreational vehicles

(e.g. boats, camping vans) and should not be placed close to or under any surfaces that will burn or

are sensitive to heat. Do not block/obstruct the flow of air and combustion around the barbecue

housing while in use.

Any enclosure in which the appliance is used shall comply with one of the following:

•An enclosure with walls on all sides, but at least one permanent opening at ground level and no

overhead cover.

•Within a partial enclosure that includes an overhead cover and no more than two walls

•Within a partial enclosure that includes an overhead cover and more than two walls, the following shall

apply-

(i) at least 25% of the total wall area is completely open: and

(ii) at least 30% of the remaining wall area is open and unrestricted.

In the case of balconies, at least 20% of the total of the side, back and front wall areas shall be and remain

open and unrestricted.

OPERATING INSTRUCTIONS

GAS TYPE AND CONSUMPTION

The barbecue is designed to operate on Universal LP Gas (Propane and/or Butane gas) or Natural Gas (via a

conversion kit). Gas consumption, Pressure and Injector Orifice size are shown on the Data Plate found on the

left-hand side of the barbecue.

GAS CONTROL KNOBS

The gas control knob locks in both the Off and High positions. By depressing the knob and turning anti-

clockwise, gas flow will gradually increase until the High position is reached. Continue turning in this direction

and gas flow will decrease until a simmer level is reached at Low. To turn gas flow off the gas control knob

must be turned clockwise from Low, depressed at High and turned until the Off position is reached.

VAPOURISER

Prior to using the barbecue, ensure the vapouriser is located in the correct position below the grill plate.

HOT PLATE, GRILL PLATE

Prior to using the barbecue, it’s advisable to cure the cooking surface. Wash the hot plate and grill plate, then

cover with olive or vegetable oil, light all burners and leave on until oil is absorbed, then wipe with a dry cloth.

DRIP TRAY

Prior to use check that the drip tray is clean and lined with aluminium foil.

UNDER NO CIRCUMSTANCES MUST SAND, FAT ABSORBENTS

OR KITTY LITTER BE USED IN THE DRIP TRAY

LIGHTING PROCEDURE

READ ALL OPERATING INSTRUCTIONS BEFORE LIGHTING.

MAKE SURE ALL GAS CONTROL KNOBS ARE IN THE ‘OFF’

POSITION AND OPEN CYLINDER VALVE.

LIGHTING THE BARBECUE

The 4 burner barbecue has a rotary ignition system built into the third gas control from the left (attached to the

third control knob from the left), which ignites the third burner from the left. The remaining burners are ignited

by a cross over channel. Pushing this control knob in, and rotating the control knob in an anti-clockwise

direction (starting at off), will cause a spark to ignite an extended pilot flame, which will in turn light the third

burner from the left. Once the knob is released, the pilot flame will extinguish. Visually check to see if the

burner has ignited. If the burner does not light, turn gas control off (turn the control knob clockwise) and allow

the unburned gas to dissipate before attempting ignition again. If ignition continues to fail refer, to the “Trouble

shooting” section. To achieve ignition on the remaining burners, turn an adjacent burner control knob to high

and the burner will ignite from the first burner.

MANUAL IGNITION

To help light the barbecue manually, a match holder and chain has been provided, and should be attached to

the right hand servery. The right hand burner can then be lit by lighting a match, fitting it into the holder and

pushing the match through to the right hand burner. After the initial burner is lit, the others can be ignited as

described above.

COOKING

GENERAL COOKING GUIDE

A fairly protected location is desirable for pleasant and efficient cooking. IMPORTANT! Strong winds will

drastically reduce cooking efficiency. As a guide, allow 10 minutes with the burners on high, to heat cooking

area. A little cooking fat (or olive oil) on the grill will prevent sticking. Cooking time for a 20mm thick steak

cooked to medium on the char grill is approximately 15 minutes (7.5 minutes per side) with the burners on

high. Turn burners down a little when full heat is not required and to LOW when not cooking.

As a guide for Hood closed cooking, use as per the following instructions: Open hood and remove the

solid plate and vapouriser. Position the grill plate central over the two centre burners. Place either the

roasting dish or a foil baking dish in the centre of the bbq. Fill the dish with 2 cm of water. Place a suitably

sized rack in the dish. Place food on the rack so that any fats will drip into the water in the bottom of the dish.

The water will also keep the food moist during cooking. With the hood open light the bbq as per normal

lighting instructions, then close the hood and turn off the two central burners. Leave the outer two burners on

high. This is most important – if left on the two centre burners will cause overheating and spoil the food. As a

rough guide to the cooking times for roast beef, allow 30 to 50 minutes cooking time per kilogram for rare to

well done respectively. It is recommended that the food be turned half way through the cooking time, for

evenness of cooking. Remember, never use the roasting hood with all the burners on high as this will cause

severe overheating and may damage the hood and bbq. During cooking, fat and scrapings will drip through

to the drip tray. Do not allow excess fat to build up in the drip tray. Clean the drip tray and replace the

aluminium foil before use. This is a general guide for roasting only – please check www.everdure.com for

any updated cooking guides.

AFTER COOKING

1. When finished, make sure burner control knobs are turned OFF.

2. TURN OFF THE GAS SUPPLY AT THE CYLINDER.

3. Immediately after cooking and whilst the barbecue is still warm, remove scraps from the grill with a

scraper.

4. Excess fat and meat scraps can be scraped off the vapouriser by removing the grill to gain access.

WARNING: Some surfaces may still be hot.

5. Clean the fat tray and replace the aluminium foil after or before each use of the appliance.

6. Once the barbecue is cool close the roasting hood and wipe off any fat splatter from the trolley with a

clean rag.

CLEANING AND STORAGE

CLEANING

Painted surfaces can be cleaned using a mild household detergent or cleaner. It is advisable to test

cleaners on a small section of the appliance first. It is recommended to clean the stainless steel surfaces

with clean water only (no detergents to be used) or use a stainless steel cleaner. Failure to follow these

instructions may void your warranty. Over time, stainless steel will be affected by “tea staining” or “bronzing”

(brown discoloration of stainless steel). This can be reduced by washing the surface with mild detergent and

warm water, followed by rinsing with clean cold water. Dry the surface afterwards.

NEVER use paint thinners or similar solvents for cleaning and NEVER pour cold water over hot surfaces.

STORAGE

WARNING:When the appliance is not in use, the cylinder valve must be turned OFF, the appliance and the

cylinder together must be stored outdoors in a well ventilated area. However it is permissible to store the

appliance (but not the cylinder) indoors. Ensure a small amount of fat or oil is on the barbecue plates to

prevent rust.

STORE CYLINDER IN A WELL VENTILATED AREA OUT OF REACH OF CHILDREN

When the gas cylinder is disconnected, replace the plug or cap on the valve outlet.

For extended storage it is suggested that the primary air port of the burners be covered against the

penetration of insects or vermin. Spiders and small insects can spin webs or nest in the burner rails/tubes,

which could lead to obstruction in the gas and air flow, resulting in a fire in an around the burner rails/tubes.

This type of fire is called a flash-back and can cause serious damage to your barbecue and create an unsafe

operating condition. To prevent this, regularly inspect and clean the burners. A barbecue cover can be

placed over the appliance for extra protection, and to reduce this.

To extend the life of your barbecue and trolley and to keep it looking great, we recommend using a

Weatherproof Cover.

GAS SUPPLY

1. Inspect the gas supply hose for any deterioration and replace it if necessary.

2. Test the gas circuit for leaks and remedy any found. See leak testing instruction.

TROLLEY

1. Check all fasteners for tightness and re tighten where necessary to ensure rigidity of the structure.

2. Wipe over barbecue trolley with a clean cloth.

OPERATING INSTRUCTIONS FOR WOK BURNER

GAS CONNECTION

Attach small hose from wok burner gas valve to barbecue manifold. Connect gas hose and

regulator to the cylinder. Before turning gas cylinder on please ensure that the gas valves on the

barbecue and wok burner are in the off position.

Turn gas supply on and check for leaks by applying a soap solution to all connections with a brush.

If a leak is detected, retighten the connection and test for leaks again. Never check for leaks with

the use of a flame.

BEFORE IGNITING THE BARBECUE ENSURE THAT ALL VALVES ON THE

BARBECUE AND THE WOK BURNER ARE IN THE OFF POSITION.

LIGHTING INSTRUCTIONS

Important: The lid must be open when lighting the burner and during normal operation.

1. Push in and turn the control knob to HIGH.

2. The built-in ignitor will light the burner.

3. If burner does not light, return knob to the OFF position and retry 5 times.

4. If the burner does not light, leave the knob in the OFF position, and wait 5 minutes before retrying.

CARE AND CLEANING

Before cleaning, ensure the appliance has cooled down and is safe to touch. Remove the trivet plate and

wipe down the burner and spill bowl with a clean damp cloth. Do not use harsh detergents or scourers as

damage may occur to the surfaces.

ESEE LIGHT SYSTEM INSTRUCTIONS

Check that the barbecue wiring is connected to the power pack (screwed onto the top of the power pack).

Check that the lighting switch is off, and plug the power pack into the power supply. With the power

supply on, the lighting switch at the front right hand corner of the barbecue can be used to turn the lights

on and off. When not in use, the unit should be disconnected from the power supply and all cords stored

within the trolley.

TROUBLESHOOTING

Burner will not ignite when using the igniter:

Cylinder valve is not on Turn cylinder valve on.

Cylinder is empty Replace with a full cylinder.

Igniter button is not working Check connections.

Igniter is not sparking Remove plate and visually check ignition box for a spark. If there is no spark

contact, check connections.

Injector is blocked Clean injector with a toothbrush. Do not drill out or use wire. Do not remove

injector. Contact authorised service centre.

Burner flame is erratic:

Burner is blocked Remove burner and check for obstruction.

Flame is burning inside burner

(hissing sound)

Turn off burner, allow to cool and re-ignite.

Regulator is faulty Contact authorised service centre.

Injector is partially blocked Clean injector with a toothbrush. Do not drill out or use wire. Do not remove

injector. Contact authorised service centre.

Gas is leaking from connections:

Connections are loose Tighten loose connections (do not over-tighten) and leak test under

pressure with soapy water solution. Refer to leak testing instructions

Hose has deteriorated Replace hose and leak test after replacement.

Gas valve is faulty Contact an authorised service centre

Threads are damaged Contact an authorised service centre

Lights not working:

Power not on Check that the power cord from the power adaptor is connected correctly

and that the power is on at the main power board.

Transformer overheated Turn off main power for half an hour before re-trying.

Globe(s) broken Replace globes.

Switch or wiring damaged Contact Everdure Service.

MAINTENANCE

It is recommended that, at the commencement of each barbecue season, the following maintenance be

conducted.

BURNERS

1. Remove the burner and inspect the port holes, primary air inlet and mixing throat for any signs of

blockage. Clean out with compressed air or a length of wire if necessary.

2. Wire brush the outside of the burner to remove rust and dirt.

3. Replace the burner.

GAS SUPPLY

1. Inspect the gas supply hose for any deterioration and replace it if necessary.

2. Test the gas circuit for leaks and remedy any found.

TROLLEY

1. Check all fasteners for tightness and re-tighten where necessary to ensure rigidity of the structure.

2. Wipe over barbecue trolley with a clean cloth.

BARBECUE ASSEMBLY

CHECK AND REMOVE THE BBQ PARTS FROM THE CARTONS

NEO Argento Esee & Figura Esee

6.COOKING PLATE

11.RIGHT SIDE PANEL

8.BODY AND HOOD ASS'Y WITH LIGHTS

5.VAPOURISER

4.GRILL

3.WARMING RACK

7.SIDE SERVERY

AND DRAWER

1.FAT TRAY

2.FAT TRAY HANDLE

12.DOORPOSTS (2PCS)

13.DOOR HANDLES (2PCS)

14.RIGHT DOOR

15.TROLLEY BOTTOM PANEL

16.CASTOR (2PCS)

9.TROLLEY TOP PANEL

10.MAGNETS (2PCS)

17.LEFT DOOR

19.WHEELS (2PCS)

18.WHEEL DECALS (2PCS)

20.AXLE

21.LEFT SIDE PANEL

23.WOK SERVERY

22.REAR PANEL

24.MATCH HOLDER

27.SERVERY BRACKET

25.BURNERS

26.POWER ADAPTOR

PARTS REQUIRED / INVENTORY

Make sure you thoroughly inspect parts before assembly and do not assemble or operate a barbecue that

appears damaged.

The use of an adjustable spanner and a Phillips screwdriver will be required.

ITEM PICTURE NAME AND QUANTITY ITEM PICTURE NAME AND QUANTITY

A SCREW M6X16…......14PCS G LOCK NUT M10….…...…2PCS

SCREW M5X15….…..32PCS H LOCK NUT M3……....…..4PCS

C SCREW M4X8…….......8PCS I SPRING WASHER D6.....14PCS

D SCREW M3X12….…....4PCS J FIBRE WASHER M5.........4PCS

E FLAT HEAD SCREW.....4PCS K SCREW M4X15……........2PCS

F NUT M6..................... 14PCS L LOCK NUT M4……....…..2PCS

Philli

s Screwdriver Spanner

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali NEO Griglia

NEO

NEO GAS-5BURN-BBQ Manuale utente

Manuali Griglia popolari di altre marche

Orbegozo

Orbegozo GR 2300 Manuale utente

bora

bora PT11 Manuale utente

Klarstein

Klarstein 10031664 Manuale utente

Garland

Garland MWE3W Manuale utente

Char-Broil

Char-Broil 463722714 Manuale utente

Nexgrill

Nexgrill 720-0830HK Manuale utente

Kenmore

Kenmore 415.16123800 Manuale utente

Camp Chef

Camp Chef PG24CLAU Manuale utente

Tucker Barbecues

Tucker Barbecues GTR Series Istruzioni per il montaggio

Monogram

Monogram ZGG540NCP1SS Manuale utente

Equipex

Equipex Sodir Savoy Manuale utente

Gaggenau

Gaggenau VR 414 610 Manuale utente

Miele

Miele KM 408-1 Manuale utente

George Foreman

George Foreman GGR50B Manuale utente

AOG

AOG T series Manuale utente

Gorenje

Gorenje TG2000CB Manuale di istruzioni

Weber

Weber Genesis Silver-B Permamount NG 051701 Manuale utente

Glen

Glen SA 3037 Manuale utente

NEO argento esee Istruzioni per l'installazione

Manuali Griglia popolari di altre marche