Ness Security Products 5000 SERIES Manuale utente

5000 SERIES 8 ZONE INSTRUCTION MANUAL

NESS SECURITY PRODUCTS

4/167 PROSPECT HIGHWAY

SEVEN HILLS. 2147

NSW AUSTRALIA

SYDNEY Phone: (02) 8825 9222 (Head Office)

BRISBANE Phone: (07) 3343 7744

MELBOURNE Phone: (03) 9878 1022

PERTH Phone: (08) 9328 2511

To the best of our knowledge the information contained in this manual is correct at the

time of going to print. NESS Security Products reserve the right to make changes so the

features and specifications at any time and without notice in the course of product

development.

TABLE OF CONTENTS

INTRODUCTION OPERATION

Terminology 2 General Information 10

Features 3 Operating Rules 10

5000 SERIES Optional Equipment 4 Arming the Control Panel 10

Specifications 4 Disarming the Control Panel 11

Monitor Mode 11

CONTROLS AND INDICATIONS 5 Emergency Functions 12

Zone Expander Functions 12

Keypad 5 Alarms 13

Audible Indications 5 Resetting an Alarm 13

Visual Indications 5 Alarm Memory 13

Zone Indications 6 Excluding Zones 14

Including Zones 14

PROGRAMMING Auxiliary Output 14

How to Enter Program Mode 6 TESTING AND TROUBLESHOOTING

How to Program 6

Access Codes 7 Testing 15

Entry Delay Time 7 Troubleshooting Guide 16

Exit Delay Time 8 Operation and Zone Summary 17

Monitor Mode Type 8

Zones to be Monitored 9

Zones to Control the Auxiliary Output 9

Programming Summary 9

INTRODUCTION ******************************************************************************************************

Thank you for purchasing a NESS 5000 At the very least, you need only know how to

SERIES Control Panel. Please do not be ARM and DISARM the Panel plus have a basic

frightened by its apparent complexity. The understanding of the indicators. Please take

Panel is very powerful but also very easy to use the time to read this manual so that you

and you only need to use as many or as few understand the full benefits of the 5000

features as you require. SERIES Control Panel.

TERMINOLOGY ************************************************************************************************

The microcomputer based 8 Zone CONTROL If you wish to protect one area while you

PANEL forms the heart of your security system occupy another, MONITOR MODE allows

and connects to all other equipment. Each selected zones to be Armed while leaving

ZONE of the Panel will be connected to one or others Disarmed.

more detection devices to protect an area such

as the front door, hallway, windows, etc. The Control Panel housing and the metal

covers over external sirens are protected by

The Panel is said to be ARMED when it is set TAMPER switches to detect someone

to detect an intruder. At other times it is attempting to disable the security system.

DISARMED. Activation of these switches will cause an

instant TAMPER ALARM.

Normally a zone is considered SECURED

Activation of a detector will cause the zone to If a detector becomes faulty, you can

be UNSECURED and may cause an alarm. EXCLUDE the associated zone so that it is

totally ignored and cannot generate an alarm.

Detectors such as fire detectors and panic INCLUDING the zone will enable it to generate

buttons must be able to generate an alarm at an alarm again.

all times regardless of the Panel setting. A

zone with this assignment is called a 24 HOUR The Control Panel is fitted with a STAND-BY

ZONE. BATTERY to ensure your security system

continues to operate it the MAINS POWER is

Before leaving the premises you must ARM the interrupted. This battery is checked every hour

Panel to enable it to detect intruders and and whenever you Arm the Panel.

generate an alarm. After ARMING, the Panel

will ignore most detectors for the EXIT DELAY Whenever an alarm occurs, it may be silenced

TIME to enable you to depart without triggering by entering an ACCESS CODE, otherwise it

an alarm. will reset at the end of RESET TIME. All

alarms are stored in MEMORY and may be

When you enter the premises the Panel will retrieved at any time by entering MEMORY

ignore selected zones for the ENTRY DELAY MODE.

TIME and will not alarm unless you fail to

DISARM the panel during this allowed time.

****************************************************************************************************

The 5000 SERIES 8 Zone Control Unique dynamic input system which will

Panel is one pan of an integrated range detect any component failure of the

of equipment. zone input circuitry and generates an

alarm.

4 Access codes. ALL inputs and outputs are heavily

Monitor mode (partial Arming). Simple protected against lightning and high

operation allows selected zones to be voltage power supply transients. An

Armed while others are ignored. Ideal earth terminal is provided for extra

for monitoring doors and windows protection.

while you are safe inside. TRUE DYNAMIC BATTERY TEST under

Additional security is provided by the load, every hour and when Arming the

various programming options: panel. Your system will warn you in

advance of possible battery failure.

- Arm via a code Works irrespective of whether the

mains is on or off.

- Exclude zones via a code A large 6.5 A-H backup battery and a

- Indication of zones that are unsecured 1.4 amp plug-pack transformer provides

when arming. more than sufficient current to maintain

the operation and security of the entire

Special interface to allow the system, even under full alarm

connection of NESS Remote Keypads conditions.

which offer full programmability and

operation of the panel from a remote The mains input is constantly

location. monitored. A warning is given when the

mains is disconnected.

Unique keyswitch input to allow simple

remote operation of the Control Panel. Audible warnings to indicate trouble

when Arming.

Easy connection of the 5000 SERIES

Satellite Siren to greatly increase the Comprehensive Memory Mode for easy

security of your system. retrieval of important events such as

Primary Alarms, Secondary Alarms,

The Control Panel housing has 4 Tamper Alarms, Low Battery and Mains

separate tamper systems - Keypad, Fail.

Wall, Lid and Panel impact. The panel

impact tamper system protects against All Programming data is permanently

control panel intrusion by heavy stored in secure non-volatile EEPROM.

impacts. These tampers are protected

24 hours a day.

Different siren sound for 24-hour

alarms

Outputs are separately fused.

5000 SERIES OPTIONAL EQUIPMENT ****************************************************************************

The following optional 5000 SERIES equipment

is available for use with the 8 zone Control

Panel. Securitel Interface Unit

Similar to the Telephone Auto Dialler but

Remote Intelligent Keypad provides higher security.

Remote or Intelligent Keypads can increase

convenience of operation and security of your Radio Control Equipment

system. A Radio Control Receiver can be connected to

the Panel to receive signals from Radio Trans-

Remote Keyswitch mitters such as hand-held panic/emergency

The Remote keyswitch will simplify the buttons.

operation of the Control Panel it is required. Real Time Event Recorder Printer

This device is connected to the Panel to

Satellite Siren RECORD and/or PRINT when any activity

Fitted with its own battery and electronics, a takes place.

Satellite Siren will operate independently of the

control panel if there is any interference to the Output Expander

system wiring. Provides 20 additional outputs for interfacing to

other equipment.

Telephone Auto Dialler

The Telephone Auto Dialler allows the 5000 Zone Expander

SERIES Control Panel to communicate alarms Provides an extra 16 Zones for the Panel.

via your telephone line.

Dialler Remote Control

This small hand-held device allows com-

munication and remote control between you at

a remote telephone and your Control Panel.

Securitel is a Trademark of Telecom Australia.

SPECIFICATIONS **********************************************************************************************

Construction 3mm Polycarbonate.

Dimensions (mm) 233 wide x 300 high x 85 deep.

Weight (with 6.5 AH battery) 3.3 kg.

Plug pack Input -240V AC. Output-17V AC. at 1.4A.

Power supply 13.8 V DC. at 1.25 Amps, current limited.

Quiescent Current Less than 80 mA.

Operating Voltage 10 V to 15V DC.

Rechargeable Battery 12 V, 6.5AH.

Battery Charge Current 450 mA maximum, current limited.

Dynamic Battery Test Every hour and when the Panel is Armed.

(whether mains power is on or off)

Dynamic Battery Test Low Voltage 10.7 V with a 5A load.

Fuses (5x20 mm) 4 x 1.5A, fast blow.

Zone Inputs End-of-line resistor = 2200 plus/minus 900 ohms

Remote Tamper Input Same as zone input.

Remote Keyswitch / Panic Button Input Same as zone input.

Remote Keypads' Inputs Proprietary.

Intelligent Keypad Outputs Proprietary.

Internal Siren Output Open collector, fused.

External Siren Output Open collector, fused.

Satellite Siren Output Proprietary.

Maximum number of Sirens 3 x 8 ohm Ohm speakers (not including Satellite

sirens since they have a separate siren driver circuit)

Latched Alarm (Strobe) Output 1.5 A at 12 V, open collector, fused.

Power Output for Optional Equipment With battery, 12 V, 1.5 A, fused.

Resetting Alarm Output 1.5 A at 12 V, open collector, fused.

24 hour Alarm Output 100 mA at 12 V, open collector, current limited.

Monitor Alarm Output 100 mA at 12 V, open collector, current limited.

Auxiliary Output 50 mA at 5 V emitter follower, current limited.

CONTROLS AND INDICATIONS

KEYPAD ******************************************************************************************************

The keypad consists of 12 buttons or keys. The PROG (or P) button is used to begin any

Each button of the keypad is used for three. programming sequence.

purposes,

a) to enter a number (eg. 1,2,3),

b) to select a client programming option

marked in blue (eg. CODE 1), The END (or E) button is used in all cases to

c) to select a command marked in white signify the end of the button sequence just

(eg. ARM). pressed.

AUDIBLE INDICATIONS

******************************************************************************************************

Every time a button is pressed the Panel At other times, the beeper will sound various

responds with a very brief beep In warnings such as 10 beeps for a low battery.

acknowledgment.

The beeper is also used to indicate whether the

entry was valid or invalid. For example, When Arming the Panel, 1-8 beeps will indicate

whenever E is pressed, all the buttons pressed that a zone is unsecured, eg. Zone 3 will be

before it are checked to see whether they are indicated by 3 long beeps.

valid. If they are valid, the response will be 3

short beeps. A continuous tone on Arming indicates a

Tamper or 24-Hour zone is unsecured. During

If they are invalid (or incorrect) the response Entry time, it indicates that an alarm has

will be 1 long beep and they will be ignored. occurred.

VISUAL INDICATIONS

******************************************************************************************************

The panel has 16 indicator lights surrounding the keypad. Each light has three basic states to indicate function.

These are: ON, OFF, FLASHING

ARMED ON The panel is Armed OFF The panel is Disarmed

MONITOR FLASHING The panel is in Monitor Mode

ALARM ON Memory mode is selected OFF No alarms

MEMORY FLASHING FAST An alarm has occurred FLASHING SLOW An alarm is stored in memory

ZONE ON The panel is in EXCLUDE mode OFF No zones are EXCLUDED

EXCLUDED FLASHING Zone(s) have been EXCLUDED

PROGRAM OFF The panel is in normal operation mode. ON The panel is in client program mode.

FLASHING SLOW The panel is in installer FLASHING FAST The program memory is faulty.

program mode.

BATTERY ON The panel battery is healthy. FLASHING The panel battery is low.

(If flashing in unison with the satellite light, the satellite

battery is low.)

MAINS ON The mains power is connected and FLASHING The mains power is disconnected or

turned on. turned off.

TAMPER OFF The control panel and satellite siren tamper FLASHING The panel or satellite siren tamper are

SATELLITE are secure and satellite siren battery is healthy. unsecured. If flashing in unison with the battery light,

the satellite battery is low.

LINE OFF The dialler is inactive. ON The dialler has seized the phone line, a dialler or

EXPAND FLASHING SLOW The dialler senses a phone zone expander option is selected.

line fault or a failure to communicate with the FLASHING FAST The dialler or zone expander has a

base station. System fault, or the dialler cannot store the information

just programmed into it.

FLASHING at the incoming call rate. The dialler is detecting an incoming call.

ZONE INDICATIONS

******************************************************************************************************

FLASHING FAST Primary alarm ie. indicates the

There are 8 Zone indicator lights above the first zone to become unsecured and cause the

keypad. In normal operating mode they show alarm.

the following states:

.FLASHING SLOW Secondary alarm - ie. indicates

OFF Zone secured those zones that have become unsecured

during the Alarm Reset time.

ON Zone unsecured As explained elsewhere in this manual,

these zone lights are used to indicate other

information in the Memory, Exclude,

Monitor, Installation and Client Program

modes.

PROGRAMMING

HOW TO ENTER PROGRAM MODE

******************************************************************************************************

The program Mode is entered whenever TO ENTER PROGRAM MODE, PRESS

programming options are to be changed.

(PROG) (MASTER CODE) (END)

IMPORTANT: The Control Panel will The Program light will be illuminated.

automatically exit the Program Mode if no keys

are pressed within a two minute period.

HOW TO PROGRAM

******************************************************************************************************

Programming the NESS 5000 SERIES 8 zone The PROG or P button is used in the selection

Control Panel is achieved via the keypad on the of PROGRAM mode, and thereafter in the

front. Every time a button is pressed, the panel selection of the option to be programmed.

responds with a very brief beep in

acknowledgment. Each button is used for

three purposes,

a) to enter a number (eg. 1,2,3), The END or E button is used in all cases to

signify the end of the button sequence just

b) to select a programming option pressed.

c) to select a command (eg. ARM).

Note: that programming options can Visual feedback of the options programmed is

only be selected whilst in PROGRAM achieved by illuminating the zone indicator

mode. lights or flashing the BATTERY/ MAINS light.

The particular type of indications are described

Programming of options can be carried out with the setting of each option in the following

in any order. pages.

All Programming follows this pattern

Select your option and VIEW the current value ENTER the new value(s)

(PROG) (OPTION) (END) (VALUE) (END)

One long beep indicates an invalid entry.

ACCESS CODES ***********************************************************************************************

The control Panel may be programmed with up 1) To program code 1 to be, say, 3456, then

to 4 separate Access Codes. Therefore each enter:

user may be allocated with their own unique

code for higher security. P 1 E 3456 E 3456 E

REMEMBER 2) To program code 2 to be, say, 9765, then

enter:

Access CODE 1 (master code) MUST

be programmed. P 2 E 9765 E 9765 E

All codes must contain a minimum of 3 3) To CANCEL code 2, then enter:

digits to a maximum of 6 digits and

must not begin with a zero. P 2 E 09765 E 09765 E

Codes 2,3 and 4 are optional.

A code may be cancelled by beginning

the code with zero.

As a security measure, the existing

code will not be displayed and the new

code must be entered twice. If the

second entry differs from the first, the

existing code will remain unchanged.

To input Code 1 ENTER

(PROG) (1) (END) (_ _ _ _ ) (END) (_ _ _ _ ) (END)

(_ _ _ _ ) Represents the numbers required as the code.

To input Code 2 ENTER

(PROG) (2) (END) (_ _ _ _ ) (END) (_ _ _ _ ) (END)

(_ _ _ _ ) Represents the numbers required as the code.

Access Codes 3 and 4 are programmed as above.

ENTRY DELAY TIME

******************************************************************************************************

The Entry Delay Time is the time the Control 1. To view the current Entry Delay Time, enter:

Panel gives you to disarm the Panel after a

delay zone is unsecured. P5E

For maximum security, the Entry Delay Time 2. The value programmed will be displayed via

should be as short as possible. the zone (1-8), battery (9) and mains (0)

lights. The display of the current value must

The Entry Delay Time can be set to a minimum be complete before a new value can be

of 1 second up to a maximum of 99 seconds. entered.

3. To change the current value to say,

10 seconds enter: 10 E

Zone 1 light will flash on for 1 second followed

by the MAINS light (0) to indicate the new value

To VIEW the Entry Delay Time ENTER To CHANGE the Entry Delay Time ENTER

(PROG) (5) (END) (VALUE) (END)

EXIT DELAY TIME

******************************************************************************************************

The Exit Delay Time is the time the Control 1. To view the current Exit Delay Time, enter:

Panel gives you to secure and depart the

premises after the Panel is Armed. P 6E

The Exit Delay Time should be just long enough 2. The value programmed will be displayed via

to allow departure comfortably without rushing the zone (1-8), battery (9) and mains (0)

and making mistakes. lights. This display of the current value must

be complete before a new value can be

entered.

The Exit Delay Time can be set to a minimum of 3. To change the current value to say,

1 second up to a maximum of 99 seconds. 80 seconds enter: 80 E

Zone 8 light will flash on for 1 second followed

by the MAINS light (0) to indicate the new value

To VIEW Exit Delay Time ENTER To CHANGE Exit Delay Time ENTER

(PROG) (6) (END) (VALUE) (END)

MONITOR MODE 'TYPE

******************************************************************************************************

The 8 zone Control Panel provides an unique The 4 different types of Monitor mode alarms

Monitor mode to ensure your security even are:

while the Panel is disarmed and the premises

are occupied. 1 = Beeper warning for the duration of the panel

entry time, then full siren alarm. Used for

perimeter protection.

Typically, Monitor mode is used to monitor the 2 = Beeper and siren operate for 2 seconds

perimeter zones (doors, windows) of a house only. Use this for medium security warnings or

while the occupants are at home or to monitor as a walk test mode.

entry through front doors or fire doors in shops

and offices while the premises are in use. 3 = Full siren alarm immediately. Use this for

high security, such as monitoring fire doors etc.

4 = Zone number is beeped out only. Use this

You can program which zones are to be for door opened warning.

monitored as well as select 1 of 4 different

types of Monitor alarms. To select, say, Monitor mode 3, enter:

P7E 3E

When the above option is programmed into the

panel, zone light 3 will flash on for 1 second.

Talk to your security installation company

about your specific requirements.

To VIEW Monitor Mode Type ENTER To CHANGE Monitor Mode Type ENTER

(PROG) (7) (END) (VALUE) (END)

ZONES TO BE MONITORED

******************************************************************************************************

Any zone can be selected for operation in To program, say, zones 3 and 4 to be

Monitor mode. However, do not select a zone Monitor zones, enter,

that has been installed to generate a 24 hour

alarm (eg. Fire Detector). P8E 2E 3E 4E

To remove a zone from the Monitor mode As each zone is programmed, the

selection, re-enter the zone number. corresponding zone light is illuminated (if it was

previously off). If the zone light was previously

on, it will be extinguished, thus de-selecting that

zone from Monitor mode.

To VIEW Zones to be monitored ENTER To CHANGE zones to be monitored ENTER

(PROG) (8) (END) (ZONE NUMBER) (END)

ZONES TO CONTROL THE AUXILIARY OUTPUT

******************************************************************************************************

The 8 Zone Control Panel provides an Auxiliary To program, say, zones 4, 6 and 8 to control

output which can be turned on and off by ANY the Auxiliary Output, enter:

selected zones or via the keypad. This output

can be used for a variety of applications. Talk P9E 4E 6E 8E

to your security installation company about

your specific requirements. As each zone is programmed, the

corresponding zone light is illuminated (if it was

A zone programmed for Auxiliary will cause the previously off). If the zone light was previously

Auxiliary Output to turn on when it becomes on, it will be extinguished, thus de-selecting

unsecured, regardless of whether the Panel is that zone.

Armed or Disarmed. The output can also be turned on or off

To remove a zone from the selection, re-enter (toggled) by pressing 9 E while Disarmed or

the zone number of the zone to be removed. in Monitor mode.

To VIEW Auxiliary Zones ENTER To CHANGE Auxiliary Zone(s) ENTER.

(PROG) (9) (END) (ZONE NUMBER) (END)

PROGRAMMING SUMMARY

******************************************************************************************************

DESCRIPTION OPTION DEFAULT PROGRAMMED

Code 1 P1E code Ecode E

Code 2 P2E code Ecode E

Code 3 P3E code Ecode E

Code 4 P4E code Ecode E

Entry Delay Time P5E time E20 secs (1-99)

Exit Delay Time P6E time E60 secs (1-99)

Monitor Type P7E type EType 2 (1-4)

Monitor Zones P6E zone EAll Zones (1-8)

Aux Output Zones P9E zone EAll Zones (1-8)

OPERATION

GENERAL INFORMATION

******************************************************************************************************

This section describes the operation of a The Control Panel is normally operated via the

typical Control Panel installation. Keep in mind keypad on the front of the Panel or the optional

that your installation may vary depending on Remote Keypad, or the optional Intelligent

the selected options and equipment. Remote Keypad.

The operating instructions which follow will

endeavour to cover the most common options.

If you have any doubts speak to your Installer.

OPERATING RULES

******************************************************************************************************

The various operations that can be performed The optional keyswitch is operated by

are indicated in white on the top of the relevant turning it clockwise (until it stops)

buttons, (eg. memory). momentarily.

Generally, the Panel will be in the Disarmed, If you make a MISTAKE while entering any

Armed or Monitor modes which provide codes, press the END (E) button and start again.

different levels of security for your premises. When you are required to enter your Access

Three other temporary modes, Program, code, you are given THREE opportunities to

Memory and Exclude, allow you to perform enter it correctly. After the third invalid attempt

various operations. The Panel will automatically the alarm is activated (requiring the correct

exit from these temporary modes it you do not code to silence the alarm). This prevents

press any buttons on the keypad within a 2 anyone trying to guess your code by entering

minute period. random numbers.

ARMING THE CONTROL PANEL

******************************************************************************************************

The Control panel must be ARMED prior to There are three methods of Arming the Panel.

vacating the premises in order to detect

intruders. a) Normally the panel is ARMED by entering on

the keypad

Ensure that the Panel is not in Program, 0 E

Memory or Exclude modes.

b) However, your Installer may have

NOTE: If the panel is already in alarm, you programmed the Panel to require the entry of

must first silence the alarm before you can a code to Arm the Panel.

Arm. 0 (CODE) E

c) If the optional keyswitch is connected, this is

turned momentarily to ARM the Panel.

1. CHECK that all windows and doors are securely locked.

2. Enter (0) (END) or (0) (CODE) (END)

3. The ARMED light should be ON and the keypad should beep 3 times.

4. Leave the premises within your Exit Delay Time.

5. At the end of the Exit Delay Time, three beeps will indicate successful Arming.

If something is wrong when Arming the control panel, the normal 3 beeps will be replaced by other warnings;

10 BEEPS Indicates either a Mains fault, Control Panel Battery fault or Satellite Siren Battery fault.

LONG BEEPS Warn that a zone is unsecured. Eg. 4 long beeps if zone 4 is unsecured.

CONSTANT TONE Indicates a 24 hour zone is unsecured. (Tamper, Panic or 24 hour zone.)

Indice

Altri manuali Ness Security Products Pannello di controllo

Ness Security Products

Ness Security Products D-8 Manuale utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche