Ness M1-G Manuale utente

M1 & M1-G Cross Platform Controller

USER’S GUIDE

This manual describes operation using KP1,

KP2, KP3 keypads. The M1 Navigator touch

screen keypad is covered separately.

REV2

M1 Cross Platform Control - User Guide

Page 2

Congratulation on purchasing one of the most advanced security systems on the market.

This system consists of a main control unit, one or more keypads, and various contact

sensors and detectors. The control unit is generally placed in an out of sight location

such as a closet, utility room, etc. It houses the main electronics and a backup battery

for standby power. Ordinarily, there is no reason for anyone except the installer or ser-

vice personnel to have access to the control unit.

Keypads are the primary user interface, and they display the current system status using

their LCD screen and LED lights. Keypads also produce audible feedback at appropri-

ate times. Generally speaking, a keypad is installed adjacent to any primary entry/exit

door(s).

THIS MANUAL IS PROVIDED TO ACQUAINT YOU WITH THE OPERATION OF THE

SYSTEM AND HELP YOU BECOME PROFICIENT WITH IT’S OPERATION. ALL

USERS SHOULD READ AND FOLLOW THE INSTRUCTIONS AND CAUTIONS

IN THIS MANUAL. FAILURE TO DO SO COULD RESULT IN THE SYSTEM

NOT WORKING PROPERLY. KEEP THIS MANUAL IN AN EASY TO ACCESS

LOCATION. READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. IF YOU

DO NOT UNDERSTAND ANY PORTION OF THIS MANUAL OR IF YOU HAVE ANY

QUESTIONS ABOUT YOUR SYSTEM, CONTACT THE INSTALLING COMPANY FOR

ASSISTANCE.

PLEASE BE AWARE OF THE FOLLOWING:

The level of security obtained is directly related to two major factors.

1. The quantity, quality, and placement of sensors attached to this system.

2. The knowledge and operating skills that you have of the system, including but not

limited to the weekly testing of the complete system.

Important notes when preparing a security/safety plan for your home or business:

1. This system is an electronic device and like any electronic device is subject to

failure or malfunction.

2. This system will not work without power.

3. This system should be tested weekly.

4. Audible warning devices will need to be loud enough, wired correctly, and properly

placed to provide adequate notication of an alarm event.

5. Smoke and heat detectors may not detect smoke and heat in all situations.

6. Only qualied security professionals should install and maintain this system.

7. It may be possible to arm this system WITHOUT the backup battery connected or

with less than an adequate charge. Weekly testing of the system with AC Power

removed should be performed to verify that the battery is connected and adequately

charged.

8. Care should be taken after testing to make certain that AC Power is restored.

M1 Cross Platform Control - User Guide

Page 3

CONTENTS

Understanding The Keypad...............................................................................4

System Notes ....................................................................................................6

Operating The System.......................................................................................7

User Codes .............................................................................................................. 7

Checking the Ready Status...................................................................................... 7

Arming in the “Away” Mode ..................................................................................... 8

Arming in the “Vacation” Mode ................................................................................ 8

Arming in the “Stay” Mode........................................................................................ 8

Auto Stay Arming ..................................................................................................... 9

Using the Quick Arm ................................................................................................ 9

Changing Stay Modes While Armed......................................................................... 9

Bypassing Zones.................................................................................................... 10

Quick Bypassing of Violated Zones........................................................................ 10

Disarming and Resetting the System ......................................................................11

Alarm Acknowledgments ........................................................................................ 12

Troubles.................................................................................................................. 12

Chime Mode, Turning On and Off .......................................................................... 13

Keypad Menus.................................................................................................14

Menu 1-View/Control Automation Functions .......................................................... 14

Menu 2-Reset Smoke Detectors ............................................................................ 16

Menu 3-Walk Test Area (zones) ............................................................................. 17

Menu 4-View History Log ....................................................................................... 17

Menu 5-View (Zone) Status.................................................................................... 18

Menu 6-Change User Codes.................................................................................. 18

Menu 7-Automation Custom Settings..................................................................... 19

Menu 8-System Settings ........................................................................................ 19

Operation by Telephone ..................................................................................21

Fire Safety & Maintenance ..............................................................................23

Silencing a Fire Alarm ............................................................................................ 23

Resetting Smoke Detectors.................................................................................... 23

Acknowledge/Reset an Alarm ................................................................................ 23

Household Fire Safety Audit................................................................................... 23

Emergency Evacuation Plans..........................................................................24

System Testing ................................................................................................25

FCC Statements (Part 15 & 68).......................................................................26

Glossary ..........................................................................................................27

M1 Cross Platform Control - User Guide

Page 4

Understanding The Keypad

Ready Light - This light will be ON when all burglar zones are secure and the system

is OK for arming. If this light is OFF, one or more zones are violated (not secure). For

maximum security, all zones should be secured before the system is armed. If this light

is FLASHING, it indicates that the system may be Force armed. Refer to the last para-

graph under “Checking the Ready Status on page 7 for more information.

Armed Light- This light will be ON when the system is armed. The mode of arm will be

indicated by the LCD display and the Exit or Stay lighted pushbuttons. This light will be

OFF when the system is disarmed.

Exit Key - This is a lighted key. When the Armed light is ON and this Exit light is ON,

the system is armed in Away (not occupied) mode. All perimeter sensors and interior

motions will be active.

Stay Key - This is a lighted key. When the Armed Light is ON and this Stay light is ON,

the system is armed in Stay (occupied) mode. Only perimeter doors and windows will

be active. Interior motions will not be active.

Chime Key - This is a lighted key. When the Chime Light is ON, a tone or announce-

ment will be heard when certain zone(s) are opened. If OFF the chime mode is off.

Bypass Key - When the Bypass Light is ON, one or more zones have been excluded or

bypassed. If OFF”, no zones are bypassed.

* Key - This key serves as a clear or reset key. If an error is made while entering digits,

pressing this key clears the error. Three presses is a master clear.

# Key - This key is currently a duplicate of the Bypass key.

MENU Key - This key is used to access the extended user menus.

Function Keys F1 thru F6 - Each key is independently programmable and lighted.

The activation as well as the lighting is programmed by the installer for special events or

conditions such as Fire, Police, or Medical emergency activation. However, these keys

may also be used for non-alarm type applications such as: gate or door openers, lights,

irrigation controls, etc. Activation may be programmed for single or double press, which

helps prevent accidental activation. If double press is programmed, it will also be pos-

sible to activate the key by pressing and holding it for at least 2 seconds.

See explanation of Emergency Activation Keys on opposite page.

M1 Cross Platform Control - User Guide

Page 5

Fire - If enabled, this key activates the local re alarm audibles and reports the alarm to

a central monitoring center, if monitoring is included as part of the system. This type of

activation is generally programmed for double press or press and hold for 2 seconds.

Police - If enabled, this key activates either a silent or audible police/holdup alarm,

depending on how the installer programmed it. It can also send a report to a central

monitoring center, if monitoring is included as part of the system. This type of activation

is generally programmed for double press or press and hold for 2 seconds.

Medical - If enabled, this key activates a medical alarm condition and sends a report to

a central monitoring center, if monitoring is included as part of the system. This type of

activation is commonly programmed for double press or press and hold for 2 seconds.

Note: As there are several keypad models available; your keypad may differ in

appearance and have different keys to the model shown here.

The MENU key may be labelled the ELK key on some keypads.

M1 Cross Platform Control - User Guide

Page 6

System Notes

Central Monitoring Station: _______________________________ Acct. # ______

Installation Company: _______________________________________________

Exit Delay 1 Timer in seconds: _______ Exit Delay 2 Timer: _______

Entry Delay 1 Timer in seconds: _______ Entry Delay 2 Timer: _______

Burglary Alarm (Audible) Cutoff Timer in minutes: _______

Fire Alarm (Audible) Cutoff Timer in minutes: _______

User Code Digits 4 digits ____ or 6 digits ____

F1 Key Function: _______________________ Single Press? Y or N Silent? Y or N

F2 Key Function: _______________________ Single Press? Y or N Silent? Y or N

F3 Key Function: _______________________ Single Press? Y or N Silent? Y or N

F4 Key Function: _______________________ Single Press? Y or N Silent? Y or N

F5 Key Function: _______________________ SinglePress? Y or N Silent? Y or N

F6 Key Function: _______________________ SinglePress? Y or N Silent? Y or N

M1 Cross Platform Control - User Guide

Page 7

Operating The System

Read this entire section before attempting to operate the system.

User Codes

<> User Codes are required for arming, disarming, and to authorize certain features

of your system. User codes can be either 4 or 6 digits (refer to System Notes).

<> If a mistake is made while entering a user code, press the asterisk key and enter

the code again.

<> To prevent someone from hunting for a code the system can be set to temporarily

lockout the keypad after repeated incorrect codes. Consult your installer or

installation record sheet for the number of incorrect attempts allowed.

Checking the Ready Status

<> When the Ready light is off, one or more zones are violated. The display will show

“Not Ready x Zn” where the x represents the number of violated zones. The system

cannot be armed until you secure or bypass the violated zone(s).

<> To identify violated zones, press the UP arrow key repeatedly to view each zone

by name and number. If a zone is programmed as bypassable, you may bypass it

(permanently exclude it) for the immediate arming cycle by pressing the Bypass key

+ zone number + the Bypass key again. The display will show “Ready w/Bypass”

once the system is ready to be armed. The Bypass key may require the entering

of a user code with an appropriate authority. NOTE: Zones not programmed as

bypassable must be secured before the system can be armed.

<> When the Ready light is on steady the alarm system is ready to be armed. The

display will show “Ready to Arm”.

<> If the Ready light is ashing, it indicates the system can be armed even though

one or zones are violated. This only occurs if the violated zones are programmed

as force-armable. Arming will temporarily exclude these violated zones from the

system. If a force armed zone becomes secure while the system is armed, it will

automatically become live, meaning that it can activate an alarm if violated. This

feature is handy for a garage door. The system can be armed while the door is up.

After backing out of the garage and closing the door, the garage door will become

normal and it will be re-included into service.

M1 Cross Platform Control - User Guide

Page 8

Arming in the “Away” Mode

Away mode arming is the highest arm level, intended for use when the prem-

ises is unoccupied. Both perimeter and interior zones will be armed.

The Ready light must be on or ashing for the alarm system to be armed.

Secure all protected doors and windows.

1. Enter a User code.

2. The Armed and Exit lights will illuminate and the exit tone will start.

4. Leave the premises during the exit delay.

5. At the end of the exit delay the alarm system will be armed Away.

During the last 10 seconds of the exit delay time the exit tone will beat faster

to warn you that the time is about to expire. If you feel that you will be unable

to get out and close the exit door in time we recommend that you return to the

keypad, disarm, and rearm.

Arming in the “Vacation” Mode

Vacation mode is a second level of Away mode. It can be used to activate

energy saving automation features when the building will not be occupied for

an extended period of time. After arming, pressing the Exit button at any time

during the exit delay time to change the armed mode to vacation.

Arming in the “Stay” Mode

Stay mode arming is intended for use when the premises is occupied. All

perimeter doors and windows are armed, and all interior zones are excluded.

Secure all protected doors and windows.

1. Enter a User code.

2. The Armed and Exit lights will illuminate and the exit tone will start.

3. Press the Stay key. The key will light up. All interior zones will be

excluded and the exit tone will be silenced. Delayed entry/exit zones

will still be delayed.

4. (Option, may not be enabled) Additional presses of the Stay key may

allow scrolling to different modes of Stay arming if enabled by your

installer. Additional modes are Stay Instant, Stay Night, and Stay Night

Instant.

M1 Cross Platform Control - User Guide

Page 9

Auto Stay Arming

(Optional) If this feature was enabled by your installer, it will automatically

change the arm mode from Away to Stay if you none of the perimeter delayed

doors are opened during the exit delay countdown time.

Secure all protected doors and windows.

1. Enter a User code.

2. The Exit key will light and the exit tone will start.

3. As long as you don’t open or exit through any delayed doors, the Stay

light will come on and the Exit light will go off at the end of the exit

delay time. The system is now armed in the Stay mode.

Using the Quick Arm

(Optional) If this feature was enabled by your installer, it will allow arming in

either the Away or Stay modes without having to enter your user code. For

security reasons however, a user code is always required to disarm.

Secure all protected doors and windows.

1. Press the Exit or Stay key.

2. The Armed and mode light (Exit or Stay) will illuminate just as if you

had entered your user code.

Changing Stay Modes While Armed

(Optional) If this feature was enabled by your installer, it permits various levels

of Stay mode arming to be enabled (scrolled) without having to rst disarm the

system. The additional Stay mode arming levels may include: Instant, Stay

Night, and Stay Night Instant.

1. Press the Exit or Stay key.

2. The Armed and mode light (Exit or Stay) will illuminate just as if you

had entered your user code.

M1 Cross Platform Control - User Guide

Page 10

Bypassing Zones

(Optional) Manual bypassing of a zone will exclude it from the system for the

immediate arming period. * [see notes below] Once the system is armed,

zone(s) that are bypassed will not be able to activate an alarm. The bypass

will remain in effect until: a) the zone bypass is cancelled, or b) the system is

disarmed. The Bypass key will be lighted whenever a zone is bypassed.

To bypass a zone:

1. Press the Bypass key.

2. Enter the number of the zone you wish to bypass.

3. Press the Bypass key again.

4. The Bypass light will light up if the bypass is accepted. However, if

the zone is non-bypassable an error tone will be heard.

Quick Bypassing of Violated Zones

(Optional) The Quick Bypass feature allows you to bypass all violated zones

with a minimum number of keystrokes. * [see notes below]

To quick bypass any violated zones:

1. Press the Bypass key.

2. Enter 999

3. Press the Bypass key again.

4. If the quick bypass is accepted the Bypass light will be illuminated.

However, if any of the zones were non-bypassable an error tone will

be heard.

* Only zones that have been programmed as bypassable can be bypassed.

* Bypassing may additionally require a user code that has been enabled with

the user bypass option.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente