NetApp FAS2240-2 Manuale utente
Installing a 2240-2 into a two-post rack
You can install your storage system in a two-post rack using a flush-mount or mid-mount installation. You use the two-post
telco tray kit for both installation types; for mid-mount installations you also use the mid-mount telco kit.
About this task
Your installation kit includes the following parts:
• Two-post telco tray kit
One two-piece equipment tray with left and right halves that attach to the back of the equipment rack to support the back of
the storage system.
• Mid-mount telco kit
• Two mid-mount mounting brackets
• Six M3.5 screws and star washers that attach the brackets to the sides of the storage system
• Bagged screws in the following sizes for mounting the two-piece telco tray and mid-mount brackets to the rack:
• 16 M5-0.8 x 20 Pilot screws
• 16 M6-1 x 20 Pilot screws
• 16 10-32 x.75 Pilot screws
• 16 12-24 x.75 Pilot screws
Steps
1. Determine which holes in the two-post rack you want to install the telco tray in using the rack alignment guide tool to ensure
that you are using the same holes on both posts of the rack.
2. Align the left-post screw holes on the two-post rack with the screw holes on the left half of the telco tray, and then secure the
telco tray to the post with two of the appropriate size and type mounting screws matching the threading of your equipment
rack.
The following illustration is a rear view of a two-post rack with the telco trays.
1
1
210-05316+A0 Copyright ©2011 NetApp, Inc. All rights reserved.
1
Telco tray
3. Repeat Step 2 for the right half of the telco tray.
4. If you are installing your storage system in a mid-mount position, go to Step 5; otherwise, slide the storage system onto the
telco tray, and secure it to the two-post rack using the screws that came with your kit.
Note: If applicable, you might need to remove the bezel to secure the storage system to the rack post; if so, you need to
replace the bezel when you are done.
5. For mid-mount installations, align the screw holes on the storage system chassis with the screw holes on the mounting
bracket, and then secure the bracket to the chassis with three of the six M5 screws and star washers.
1
Telco tray
2
Rack post
3
Mid-mount bracket
6. Repeat Step 5 for the other mid-mount bracket.
7. Slide the storage system onto the telco tray until the brackets on the chassis meet the rack posts, and then secure the brackets
to the rack posts with six of the appropriate size and type mounting screws matching the threading of your equipment rack.
2Installing a 2240-2 into a two-post rack
Indice
Altri manuali NetApp Magazzinaggio
NetApp
NetApp AFF A400 Manuale
NetApp
NetApp DE6600 Manuale utente
NetApp
NetApp FAS8200 Series Manuale
NetApp
NetApp FAS500f Manuale utente
NetApp
NetApp FAS2800 Manuale
NetApp
NetApp NearStore R100 Manuale utente
NetApp
NetApp AFF A200 Manuale utente
NetApp
NetApp DS4486 Manuale
NetApp
NetApp StorageGRID Webscale SG6000 Series Manuale utente
NetApp
NetApp FAS8200 Series Manuale utente
NetApp
NetApp AFF A400 Manuale utente
NetApp
NetApp AFF A320 Manuale utente
NetApp
NetApp FAS8300 Manuale utente
NetApp
NetApp DS4243 Manuale
NetApp
NetApp E5700 Manuale utente
NetApp
NetApp DS2246 Manuale
NetApp
NetApp DE6900 Manuale utente
NetApp
NetApp E Series Manuale utente
NetApp
NetApp DS224C Manuale utente
NetApp
NetApp HCI Manuale utente
