NetApp FAS500f Manuale utente

FAS systems

ONTAP Systems

NetApp

June 13, 2022

This PDF was generated from https://docs.netapp.com/us-en/ontap-systems/fas500f/install-setup.html on

June 13, 2022. Always check docs.netapp.com for the latest.

Table of Contents

FAS systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

FAS500f System Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

FAS2600 System Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê90

FAS2700 System Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê174

FAS8200 System Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê289

FAS8300 and FAS8700 System Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê408

FAS9000 System Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê537

FAS9500 systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê683

FAS systems

FAS500f System Documentation

Install and setup

Start here: Choose your installation and setup experience

For most configurations, you can choose from different content formats.

•Quick steps

A printable PDF of step-by-step instructions with live links to additional content.

•Video steps

Video step-by-step instructions.

•Detailed steps

Online step-by-step instructions with live links to additional content.

If your system is in a MetroCluster IP configuration, see the Install MetroCluster IP Configuration instructions.

Quick steps - FAS500f

This section gives graphic instructions for a typical installation of your system from

racking and cabling, through initial system bring-up. Use this guide if you are familiar with

installing NetApp systems.

Access the Installation and Setup Instructions PDF poster:

•English: FAS500f Installation and Setup Instructions

•Japanese: FAS500f Systems Installation and Setup Instructions

•Chinese: FAS500f Systems Installation and Setup Instructions

Videos - FAS500f

There are two videos - one showing how to rack and cable your system and one showing

an example of using the System Manager Guided Setup to perform initial system

configuration.

Video one of two: Hardware installation and cabling

The following video shows how to install and cable your new system.

Installation and Setup of a FAS500f

Video two of two: Performing end-to-end software configuration

The following video shows end-to-end software configuration for systems running ONTAP 9.2 and later.

NetApp video: Software configuration for vSphere NAS datastores for FAS/AFF systems running ONTAP 9.2

Detailed steps - FAS500f

This section gives detailed step-by-step instructions for installing a FAS500f system.

Step 1: Prepare for installation

To install your FAS500f system, you need to create an account and register the system. You also need to

inventory the appropriate number and type of cables for your system and collect specific network information.

You need to have access to the NetApp Hardware Universe (HWU) for information about site requirements as

well as additional information on your configured system. You might also want to have access to the Release

Notes for your version of ONTAP for more information about this system.

What you need

You need to provide the following at your site:

•Rack space for the storage system

•Phillips #2 screwdriver

•Additional networking cables to connect your system to your network switch and laptop or console with a

Web browser

Steps

1. Unpack the contents of all boxes.

2. Record the system serial number from the controllers.

3. Set up your account:

a. Log in to your existing account or create an account.

b. Register (NetApp Product Registration) your system.

4. Download and install NetApp Downloads: Config Advisor on your laptop.

5. Inventory and make a note of the number and types of cables you received.

The following table identifies the types of cables you might receive. If you receive a cable not listed in the

table, see the NetApp Hardware Universe to locate the cable and identify its use.

Type of cable… Part number and length Connector type For…

25 GbE cable X66240A-05 (112-00595),

0.5m;

X66240-2 (112-00573),

Cluster interconnect

network

X66240A-2 (112-00598),

2m;

X66240A-5 (112-00600),

Data

100 GbE cable X66211-2 (112-00574),

2m;

X66211-5 (112-00576),

Storage

RJ-45 (order dependent) Not applicable Management network

(BMC and wrench port)

and Ethernet data (e0a

and e0b)

Fibre Channel X66250-2 (112-00342)

2m;

X66250-5 (112-00344)

5m;

X66250-15 (112-00346)

15m;

X66250-30 (112-00347)

30m

Micro-USB console cable Not applicable Console connection

during software setup

Power cables Not applicable Powering up the system

1. Review the ONTAP Configuration Guide and collect the required information listed in that guide.

Step 2: Install the hardware

You need to install your system in a 4-post rack or NetApp system cabinet, as applicable.

Steps

1. Install the rail kits, as needed.

2. Install and secure your system using the instructions included with the rail kit.

You need to be aware of the safety concerns associated with the weight of the system.

3. Identify and manage cables because this system does not have a cable management device.

4. Place the bezel on the front of the system.

Step 3: Cable controllers

There is required cabling for your platform’s cluster using the two-node switchless cluster method or the cluster

interconnect network method. There is optional cabling to the Fibre Channel or iSCSI host networks or direct-

attached storage. This cabling is not exclusive; you can have cable to a host network and storage.

Required cabling: Cable controllers to a cluster

Cable the controllers to a cluster by using the two-node switchless cluster method or by using the cluster

interconnect network.

Option 1: Cable a two-node switchless cluster

The management, Fibre Channel, and data or host network ports on the controller modules are connected to

switches. The cluster interconnect ports are cabled on both controller modules.

Before you begin

Contact your network administrator for information about connecting the system to the switches.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Steps

1. Use the animation (Cable a two-node switchless cluster) or the step-by-step instructions to complete the

cabling between the controllers and to the switches:

Step Perform on each controller

Cable the cluster interconnect ports to each other with the 25GbE cluster interconnect cable

•e0c to e0c

•e0d to e0d

Cable the wrench ports to the management network switches with the RJ45 cables.

DO NOT plug in the power cords at this point.

2. To complete setting up your system, see Step 4: Complete system setup and configuration.

Option 2: Cable a switched cluster

All ports on the controllers are connected to switches; cluster interconnect, management, Fibre Channel, and

data or host network switches.

Before you begin

Contact your network administrator for information about connecting the system to the switches.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Steps

1. Use the animation (Cabling a switched cluster) or the step-by-step instructions to complete the cabling

between the controllers and to the switches:

Step Perform on each controller

Cable the cluster interconnect ports to the 25 GbE cluster interconnect switches.

•e0c

•e0d

Cable the wrench ports to the management network switches with the RJ45 cables.

DO NOT plug in the power cords at this point.

2. To complete setting up your system, see Step 4: Complete system setup and configuration.

Optional cabling: Cable configuration-dependent options

You have configuration-dependent optional cabling to the Fibre Channel or iSCSI host networks or direct-

attached storage. This cabling is not exclusive; you can have cabling to a host network and storage.

Option 1: Cable to a Fibre Channel host network

Fibre Channel ports on the controllers are connected to Fibre Channel host network switches.

Before you begin

Contact your network administrator for information about connecting the system to the switches.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Step Perform on each controller module

1 Cable ports 2a through 2d to the FC host switches.

2 To perform other optional cabling, choose from:

•Option 2: Cable to a 25GbE data or host network

•Option 3: Cable the controllers to a single drive shelf

3 To complete setting up your system, see Step 4: Complete system setup and configuration.

Option 2: Cable to a 25GbE data or host network

25GbE ports on the controllers are connected to 25GbE data or host network switches.

Before you begin

Contact your network administrator for information about connecting the system to the switches.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Step Perform on each controller module

1 Cable ports e4a through e4d to the 10GbE host network switches.

2 To perform other optional cabling, choose from:

•Option 1: Cable to a Fibre Channel host network

•Option 3: Cable the controllers to a single drive shelf

3 To complete setting up your system, see Step 4: Complete system setup and configuration.

Option 3: Cable the controllers to a single drive shelf

You must cable each controller to the NSM modules on the NS224 drive shelf.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Steps

Altri manuali per FAS500f

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali NetApp Magazzinaggio

NetApp

NetApp FAS25 Series Manuale utente

NetApp

NetApp AFF A400 Manuale utente

NetApp

NetApp H410S Manuale del proprietario

NetApp

NetApp FAS26 Series Manuale

NetApp

NetApp DS4243 Manuale

NetApp

NetApp StorageGRID Webscale SG5700 Series Manuale operativo

NetApp

NetApp FAS22 Series Manuale utente

NetApp

NetApp AFF A800 Manuale utente

NetApp

NetApp AFF A400 Manuale utente

NetApp

NetApp DS4243 Istruzioni di installazione e manutenzione

NetApp

NetApp FAS9500 Foglio di istruzioni

NetApp

NetApp AFF A400 Manuale

NetApp

NetApp FAS8300 Manuale

NetApp

NetApp AFF A400 Manuale

NetApp

NetApp FAS8300 Manuale utente

NetApp

NetApp SOLIDFIRE Manuale utente

NetApp

NetApp AFF A200 Manuale dell'operatore

NetApp

NetApp StorageGRID Webscale SG6000 Series Manuale operativo

NetApp

NetApp H410S Manuale

NetApp

NetApp StorageGRID Webscale SG5700 Series Manuale operativo

NetApp

NetApp SteelStore 30 Series Manuale utente

NetApp

NetApp DS460C Manuale utente

NetApp

NetApp E-Series 3040 40U Manuale utente

NetApp

NetApp AFF A400 Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente