NETGEAR PLP1200 Manuale utente
Quick Start
Powerline 1200 + Extra Outlet
Model PLP1200
2
Package Contents
In some regions, a resource CD is included with your product.
3
Getting Started
Powerline adapters provide an alternative way to extend your network
using your existing electrical wiring. Plug two or more Powerline adapters
into electrical outlets to create a wired network connection. You can add
up to 16 Homeplug AV-certified and AV2-certified adapters to extend
your network. For a complete list of Homeplug AV-certified devices, visit
http://www.homeplug.org/certified_products.
4
Meet Your Adapter
Before you install your adapter, familiarize yourself with its LEDs,
buttons, and port.
Ethernet port Security button
Factory Reset button
Power LED
Ethernet LED
Pick A Plug LED
5
Power LED Green. The electrical power is on.
Amber. The adapter is in power saving mode.
Blinking green. The adapter is in the process of setting up
security.
O. The adapter is not receiving electrical power.
Ethernet LED Lit. The Ethernet port is linked.
O. No Ethernet connection is detected.
Pick A Plug LED The Pick A Plug feature lets you pick the electrical outlet with
the strongest performance, indicated by the color displayed
by the LED:
Red. Link rate < 50 Mbps (good).
Amber. Link rate > 50 and < 80 Mbps (better).
Green. Link rate > 80 Mbps (best).
O. The adapter did not find any other compatible Powerline
devices using the same encryption key.
Factory Reset
button
Press the Factory Reset button for one second, then release
it to return the Powerline adapter to its factory default
settings.
6
Ethernet port Use an Ethernet cable to connect your wired devices,
including computers, WiFi routers, or game consoles, to your
Powerline network.
Security button Use the Security button to create a secure Powerline
network.
7
Install Your Adapters
Room 1 Room 2
8
Secure Your Network
¾To create a secure network:
1. Plug in your new adapters.
2. Wait until the Pick A Plug LED is lit.
3. Press the Security button for two seconds, then press the Security
button on one of the other adapters in your existing network for two
seconds. Both buttons must be pressed within two minutes.
Note: The Security button does not work in power saving mode (see
Troubleshooting Tips on page 10).
Warning: Do not press the
Security
button on the Powerline adapter
until installation is complete and the adapters are communicating with
each other (indicated by the blinking Power LED). Pressing this button too
soon can temporarily disable Powerline communication. If this occurs, use
the Factory Reset button to return the Powerline adapter to its factory
default settings.
Note: If you want to add another adapter aer creating a secure
Powerline network, perform a factory reset on all of the adapters and then
perform this procedure.
9
Add Adapters
To add adapters before you configure the security feature, just plug them
in and connect the adapters to your equipment.
¾To add adapters to a Powerline network with security set:
1. Plug in and connect the new adapters.
2. On all of the previously installed adapters, press and hold the Factory
Reset button for one second.
This returns them to the factory settings.
3. Secure the Powerline network:
a. On any of the adapters, press and hold the Security button
for two seconds.
b. On any one of the other adapters, press and hold the
Security button for two seconds.
Both buttons must be pressed within two minutes.
10
Troubleshooting Tips
Power LED is o. Make sure that power is supplied to the electrical
outlet, and that the Powerline devices are not plugged
into an extension cord, power strip, or surge protector.
Power LED is blinking
amber.
Power saving mode occurs when the Ethernet LED is
o. This can occur in the following circumstances:
• The Ethernet cable is unplugged.
• The device connected through the Ethernet cable
is turned o.
• The adapter is idle for 10 minutes.
It returns to normal mode within two seconds
aer the Ethernet link is up.
Pick A Plug LED is o. • If you already set network security, make sure
that all Powerline devices are using the same
encryption key; see the online user manual for
details.
• Press the Factory Reset button on each device
for one second to return the Powerline adapter to
its factory default settings.
Altri manuali per PLP1200
1
Indice
Altri manuali NETGEAR Adattatore
NETGEAR
NETGEAR XAVB1601 Manuale utente
NETGEAR
NETGEAR WNDA3100v2 - RangeMax Dual Band Wireless-N USB 2.0... Manuale utente
NETGEAR
NETGEAR XAV2001 - Powerline AV Ethernet Adapter Manuale utente
NETGEAR
NETGEAR EPS90W Manuale utente
NETGEAR
NETGEAR GA302T Manuale utente
NETGEAR
NETGEAR EA101C Manuale utente
NETGEAR
NETGEAR XAV1301v1/XAVB1301v1 Manuale di formazione
NETGEAR
NETGEAR XAV1301v1/XAVB1301v1 Manuale utente
NETGEAR
NETGEAR XA601 - Powerline USB Adapter Manuale utente
NETGEAR
NETGEAR RB-WPN111NA Manuale utente
NETGEAR
NETGEAR XAV5004 - POWERLINE AV 500 ADAPTER Manuale utente
NETGEAR
NETGEAR G54/N150 WNA1000Mv2 Manuale utente
NETGEAR
NETGEAR XAVB101V2 Manuale utente
NETGEAR
NETGEAR GA302T Manuale utente
NETGEAR
NETGEAR A6150 Manuale utente
NETGEAR
NETGEAR GA311 - Gigabit PCI Adapter Manuale utente
NETGEAR
NETGEAR XAV5601 Manuale utente
NETGEAR
NETGEAR XAVB2602 Manuale utente
NETGEAR
NETGEAR TA612V Manuale utente
NETGEAR
NETGEAR GA511 - Gigabit Ethernet PC Card Manuale utente
