NETGEAR Powerline PLP2000 Manuale utente
Quick Start
Powerline 2000 + Extra Outlet
Model PLP2000 (2 x PLP2000)
2
Package Contents
In some regions, a resource CD is included with your product.
3
Getting Started
Powerline adapters give you an alternative way to extend your network
using your existing electrical wiring. Plug two or more Powerline adapters
into electrical outlets to create a wired network connection. You can add
up to 16 adapters to extend your network.
4
Meet Your Adapter
Before you install your adapter, familiarize yourself with its LEDs, buttons,
and port.
Ethernet ports
Security/Factory Reset button
Power LED
Ethernet LED
Pick A Plug LED
5
Power LED Solid green. The electrical power is on.
Slow blinking green (blink every three seconds). The
adapter is in power saving mode.
Blinking green (blink every second). The adapter is in the
process of setting up security.
O. The adapter is not receiving electrical power.
Ethernet LED Solid green. The Ethernet port is linked.
O. No Ethernet connection is detected.
Pick A Plug LED The Pick A Plug feature lets you pick the electrical outlet with
the strongest performance, indicated by the color displayed
by the LED:
Red. Link rate < 50 Mbps (good).
Amber. Link rate > 50 and < 80 Mbps (better).
Green. Link rate > 80 Mbps (best).
O. The adapter did not find any other compatible Powerline
devices using the same encryption key.
6
Security/Factory
Reset button
Press and hold the Security/Factory Reset button for 1 to
3 seconds and then release it to create a secure Powerline
network.
Press and hold the Security/Factory Reset button for 8
to 10 seconds, and then release it to return the Powerline
adapter to its factory default settings.
Ethernet ports Two GbE ports. Use Ethernet cables to connect your wired
devices, including computers, WiFi routers, or game consoles,
to your Powerline network.
For information about the standards your adapter meets, see the user
manual.
7
Install Your Adapters
Room 1 Room 2
8
Secure Your Network
Setting security is optional, but highly recommended.
¾To create a secure network:
1. Plug in your new adapters.
2. Wait until the Pick A Plug LEDs are lit.
3. Press the Security/Factory Reset button on one of the adapters for
two seconds, and then press the Security/Factory Reset button on
one of the other adapters in your existing network for two seconds.
You must press both buttons within two minutes.
Once secure pairing completes successfully, the power LEDs and Pick
A Plug LEDs are lit and the adapter can access the internet.
4. If you are installing additional adapters, repeat Step 3 with one of the
secure adapters and one of the adapters that is not yet secured.
Note: The Security/Factory Reset button does not work in power
saving mode (see Troubleshooting Tips on page 10).
Warning: Do not press the
Security/Factory Reset
button on the
Powerline adapter until installation is complete and the adapters are
communicating with each other (indicated by the blinking Power
LED). Pressing this button too soon can temporarily disable Powerline
communication. If this occurs, press and hold the Security/Factory
Reset button for 8 to 10 seconds to return the Powerline adapter to its
factory default settings.
9
Add Adapters
To add adapters before you configure the Security Reset feature, just plug
them in and connect the adapters to your equipment.
¾To add adapters to a Powerline network with security set:
1. Plug in and connect the new adapters.
2. On any of the adapters that are already a part of the secure network,
press and hold the Security/Factory Reset button for two seconds.
3. On the new adapter, press and hold the Security/Factory Reset
button for two seconds.
You must press both buttons within two minutes.
10
Troubleshooting Tips
Power LED is o. Make sure that power is supplied to the electrical
outlet, and that the Powerline devices are not plugged
into an extension cord, power strip, or surge protector.
Power LED is slowly
blinking green.
Power saving mode occurs when the Ethernet LED is
o. This can occur in the following circumstances:
• The Ethernet cable is unplugged.
• The device connected through the Ethernet cable
is turned o.
• The adapter is idle for 10 minutes.
It returns to normal mode within two seconds
aer the Ethernet link is up.
Pick A Plug LED is o. • If you already set network security, make sure
that all Powerline devices are using the same
encryption key. See the online user manual for
details.
• Press and hold the Security/Factory Reset
button for 8 to 10 seconds on each device to
return the Powerline adapter to its factory default
settings.
Indice
Altri manuali NETGEAR Adattatore
NETGEAR
NETGEAR EA101C Manuale utente
NETGEAR
NETGEAR WG111U - Double 108 Mbps Wireless USB 2.0... Manuale utente
NETGEAR
NETGEAR EA101 Manuale utente
NETGEAR
NETGEAR PowerLINE PLW1010v2 Manuale utente
NETGEAR
NETGEAR GA311 - Gigabit PCI Adapter Manuale utente
NETGEAR
NETGEAR RB-WPN111NA Manuale utente
NETGEAR
NETGEAR WPNT121 - RangeMax 240 USB 2.0 Adapter Manuale utente
NETGEAR
NETGEAR XAV5001 - Powerline AV 500 Adapter Manuale utente
NETGEAR
NETGEAR XA601 - Powerline USB Adapter Manuale utente
NETGEAR
NETGEAR PTVU1000 Manuale utente
NETGEAR
NETGEAR EPS90W Manuale utente
NETGEAR
NETGEAR MCA1001 - MoCA Coax-Ethernet Adapter Manuale utente
NETGEAR
NETGEAR XAVB5501 Manuale utente
NETGEAR
NETGEAR MA111 Manuale utente
NETGEAR
NETGEAR XAV2501 - Powerline AV Ethernet Adapter Manuale utente
NETGEAR
NETGEAR XETB1001 - 85 MBit/s Powerline Network... Manuale utente
NETGEAR
NETGEAR RB-WN111 Manuale utente
NETGEAR
NETGEAR RangeMax WPNT511 Manuale utente
NETGEAR
NETGEAR WN2500RP-100PAS Manuale utente
NETGEAR
NETGEAR A6210 Manuale utente
