NETGEAR MR814 - 802.11b Cable/DSL Wireless Router Guida utente
August 2007
208-10147-01
v1.0
NETGEAR, Inc.
4500 Great America Parkway
Wireless Router Setup
Manual
ii
Trademarks
NETGEAR and the NETGEAR logo are registered trademarks, and RangeMax and Smart Wizard are trademarks of
NETGEAR. Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other
brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
© 2007 by NETGEAR, Inc. All rights reserved.
Contents iii
Contents
Getting to Know Your Wireless Router................................................................................1
Unpacking Your New Router .............................................................................................1
What You Need Before You Begin .....................................................................................6
Updating Your Router Firmware ........................................................................................6
Two Setup Methods: Smart Wizard Setup or Manual Setup .............................................6
Smart Wizard Setup ..........................................................................................................7
Manual Setup ....................................................................................................................7
Product Registration, Support, and Documentation ........................................................12
Accessing the Wireless Router after Installation and Checking for New Firmware .........13
Setting Up and Testing Basic Wireless Connectivity .......................................................15
Implementing Appropriate Wireless Security ...................................................................16
Help with Troubleshooting..................................................................................................19
Basic Troubleshooting .....................................................................................................19
Troubleshooting Connectivity Using the Ping Utility ........................................................25
Technical Specifications .....................................................................................................27
Factory Default Settings ..................................................................................................27
Related Documents..............................................................................................................31
iv Contents
Getting to Know Your Wireless Router 1
v1.0, August 2007
Getting to Know Your Wireless Router
Congratulations on your purchase of a NETGEAR® high-speed wireless router, the Wireless
Router Model WPN824v3.
Before you begin installing your router, check the package contents (see Unpacking Your New
Router). Become familiar with the front and back panels of your router—especially the status
lights—and the important information on the router label (see “Bottom Label” on page 5).
Unpacking Your New Router
The product package should contain the following items:
• The wireless router
• A snap-on stand for your wireless router
• An AC power adapter (varies by region)
• A yellow Ethernet cable
•TheResource CD, which includes:
– The Smart Wizard Installation Assistant (Autorun.exe)
– A PDF version of this manual
– A link to the online User Manual
• Warranty and Support Information cards
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
To prepare your router for installation:
1. Carefully peel off the protective film covering the sides of your router.
Wireless Router Setup Manual
2 Getting to Know Your Wireless Router
v1.0, August 2007
2. Set up your wireless router by inserting the router into the stand supplied with your router.
3. Place your router in an area suitable for installation (near an AC power outlet and accessible to
the Ethernet cables for your wired computers).
Figure 1
Wireless Router Setup Manual
Getting to Know Your Wireless Router 3
v1.0, August 2007
Router Front Panel
You can use the status lights on the front of the wireless router to verify various conditions.
Figure 2
Table 1-1. Status Light Descriptions
Item Function Activity Description
1Power On green solid
Off Power is supplied to the router.
Power is not supplied to the router.
2
Test On
Off
Slow blinking
The unit is performing the power-on self-test diagnostic.
The unit successfully completed the power-on self-test diagnostic.
The reset button is being pushed, restoring the factory default
settings.
3
Wireless On
Off
Blinking
The wireless interface is enabled.
The wireless interface is turned off.
Data is being communicated over the wireless network.
4
Internet Amber off
Amber on
Amber blinking
Green off
On
Blinking
No Ethernet cable is connected to the modem.
The Ethernet cable connection to the modem is good.
Packets are being transmitted and received from a modem or other
network device, but no IP address has been received.
No IP address has been received.
IP address has been received.
IP address received and data is being transmitted and received.
5LAN Green
Amber The LAN port has detected a 100 Mbps link with an attached device.
The LAN port has detected a 10 Mbps link with an attached device.
Wireless Router Setup Manual
4 Getting to Know Your Wireless Router
v1.0, August 2007
Router Back Panel
The rear panel of the WPN824v3 router contains the items in the list that follows the figure.
The back of the wireless router includes:
1. On/off switch for the antenna dome light
2. AC power adapter outlet
3. Four local (LAN) 10/100 Mbps Ethernet ports for connecting the router to the local computers
4. Internet (WAN) Ethernet port for connecting the router to a cable or DSL modem
5. Factory default reset button
Figure 3
4
3
2
15
Wireless Router Setup Manual
Getting to Know Your Wireless Router 5
v1.0, August 2007
Top Panel
The top of the wireless router includes a dome with status lights that identify which of the seven
internal antennas are active. The lights flash according to the direction of the wireless signal.
These status lights are off by default but can be turned on using the on/off switch (see “Router
Back Panel” on page 4).
Bottom Label
View the label on the bottom of the wireless router to identify the serial number, port connectors,
status lights, and default login information.
Figure 4
Figure 5
Wireless Router Setup Manual
6 Getting to Know Your Wireless Router
v1.0, August 2007
What You Need Before You Begin
Prepare the following before you set up your router:
• Internet service.
• The configuration information your Internet Service Provider (ISP) gave you. Depending on
how your Internet account was set up, you might need one or more of these settings for the
wireless router to access the Internet:
— Host and domain names
— Internet login name and password (frequently an e-mail address and password)
— Domain Name Server (DNS) addresses
— Fixed or static IP address
Your ISP should have provided you with all the information needed to connect to the Internet.
If you cannot locate this information, you can ask your ISP to provide it.
• For cable modem service, use the computer you first used to set up your Internet service.
Updating Your Router Firmware
NETGEAR is always improving the operability and features included with your router. To make it
easy for you to receive the best, most up-to-date features of your router, NETGEAR provides a
variety of methods for updating your product.
• The Smart Wizard installation assistant lets you check for and install updates as part of the
setup activity.
• The router includes an update feature that lets you check for and install updates. You must be
logged in to the router to use this feature.
These options are discussed in “Accessing the Wireless Router after Installation and Checking for
New Firmware” on page 13.
Two Setup Methods: Smart Wizard Setup or Manual
Setup
You have two methods available for setting up your wireless router:
Altri manuali per MR814 - 802.11b Cable/DSL Wireless Router
3
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali NETGEAR Router di rete
NETGEAR
NETGEAR Nighthawk RAX200 Manuale utente
NETGEAR
NETGEAR RT338 Manuale utente
NETGEAR
NETGEAR RT311 Manuale utente
NETGEAR
NETGEAR WNDR4300 Foglio di istruzioni
NETGEAR
NETGEAR RH348 Manuale utente
NETGEAR
NETGEAR N750 Manuale utente
NETGEAR
NETGEAR RBK843S Manuale utente
NETGEAR
NETGEAR BR500 Manuale
NETGEAR
NETGEAR DG834v4 Manuale utente
NETGEAR
NETGEAR MS70 Manuale utente
NETGEAR
NETGEAR XS512EM Manuale utente
NETGEAR
NETGEAR RP334 Manuale utente
NETGEAR
NETGEAR D6220 Manuale utente
NETGEAR
NETGEAR RAXE500 Manuale utente
NETGEAR
NETGEAR FS524S - Switch - Stackable Manuale utente
NETGEAR
NETGEAR ETHERNET SWITCH SW108 Manuale utente
NETGEAR
NETGEAR RAX5 Manuale utente
NETGEAR
NETGEAR DGFV338 - ProSafe Wireless ADSL Modem VPN Firewall... Manuale utente
NETGEAR
NETGEAR ProSafe JFS516 Manuale utente
NETGEAR
NETGEAR R8000P Manuale utente
