NETGEAR Arlo Manuale utente

Quick Start Guide

Welcome

Thank you for choosing Arlo.

Getting started is easy.

What’s Included

Base station

power adapter

Ethernet cable Wall mount* Mounting screws

and anchors*

Arlo Wire-Free

camera

Lithium CR 123 batteries*

* Quantity varies with number of cameras

(VMB3500)

Connect Your Base Station to the Internet

a. Connect the base station to your router using the Ethernet cable that is included.

SYNC

Ethernet DC

Reset

Get the App

For the best experience, download the Arlo app for your smartphone by scanning this QR code or

searching for Arlo in the app store.

arlo.netgear.com

Get an Account

b. Connect the AC adapter to your base station and plug it in.

The Power LED and Internet LED on the back of the base station light green in about two

minutes.

(If this doesn’t happen, visit

arlo.com/support/ for troubleshooting tips.)

SYNC

Ethernet

Reset

¾To create a new Arlo account:

a. Launch the Arlo app from your smartphone, tap the

New to Arlo? button, and select Arlo Wire-Free.

If you are using a computer, visit arlo.netgear.com.

b. Follow the onscreen instructions.

¾To add an Arlo camera to an existing Arlo account:

a. If you already set up an Arlo account, log in, and click or

tap Add Device.

b. Follow the onscreen instructions.

SYNC

Reset

Ethernet DC

SYNC

Ethernet DC

Insert Batteries Into Your Cameras

a. Unlock the battery

compartment by

sliding and holding the

latch.

b. Slide the battery door

back and lift it to

open the compartment.

SYNC

Ethernet

Reset

Note: Cameras must be synced one at a time.

a. Bring the camera within 1 to 3 feet (30 to 100 centimeters) of the base station.

c. Insert two batteries

near the back of the

camera.

d. Insert two batteries

near the

compartment hinge.

e. Close the

battery door.

Sync Your Cameras With the Base Station

1110

SYNC

Ethernet

Reset

SYNC

Ethernet

Reset

Syncing more than one camera?

Go to page 9 and repeat steps 5a

through 5d for each camera.

A blue LED on the camera blinks slowly

when the sync process starts. The blue

LED blinks rapidly to conﬁrm sync.

The camera is ready for viewing.

Note: If the LED blinks amber quickly, the sync is not

successful. You must repeat the sync process.

b. Press the Sync button on the back of

the base station for about two seconds.

Release the button.

c. Wait for the Sync Status LED to blink

green.

d. Press the Sync button on top of the

camera for about two seconds. Release

the button.

1312

To mount your camera to the wall:

Fasten the mounting screw into the wall,

and hang the magnetic mount from

the screw.

If you’re mounting the camera to drywall,

be sure to use the plastic drywall anchors

that are provided.

Tip: You can also use double-sided tape instead

of screws.

Place or Mount Your Cameras

Locate a spot for your camera

You can place your camera on a shelf or

other ﬂat surface, or you can mount it to

the wall.

Tip: Use the Arlo app in Position mode

(found in Camera Settings) to help aim the camera.

1514

Base Station LED Guide

Green

The base station

is powered on.

Blinking green

A ﬁrmware update

is in progress. DO

NOT TURN OFF

BASE STATION OR

CAMERAS.

O

The base station

is powered o.

Green

The base station

is connected to

the Internet.

Blinking green

The base station is

sending data over

the Internet.

Amber

The base station is

connected to the

router but did not

establish an Internet

connection.

O

The base station is

not connected to

your router.

Green

Cameras are

connected to the

base station.

Blinking green

The base station is

attempting to sync

with a camera.

Blinking amber

A camera is too

far from the base

station. Signal

strength is weak.

O

No cameras are

detected.

Amber

The base station

is booting.

You’re Done!

Congratulations! Your Arlo System is set up and ready to go.

To view useful tutorial videos, ﬁnd troubleshooting tips, or

get support, visit arlo.com/support/.

Power Internet Camera

SYNC

Ethernet

Reset

Amber

The base station is

not assigned to an

Arlo account.

©NETGEAR, Inc., NETGEAR, the NETGEAR Logo, and Arlo are trademarks of NETGEAR, Inc.

Compliance

For the current EU Declaration of Conformity, visit

http://kb.netgear.com/app/answers/detail/a_id/11621/.

For regulatory compliance information, visit

http://www.netgear.com/about/regulatory/.

350 East Plumeria Drive

San Jose, CA 95134, USA

February 2018

NETGEAR INTL LTD

Building 3, University Technology Centre

Curraheen Road, Cork, Ireland

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this

equipment.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Altri manuali per Arlo

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali NETGEAR Telecamera di sicurezza

NETGEAR

NETGEAR arlo Wire-Free Camera Manuale utente

NETGEAR

NETGEAR Arlo Go Manuale utente

NETGEAR

NETGEAR VMS4130-100EUS Manuale utente

NETGEAR

NETGEAR VueZone Manuale utente

NETGEAR

NETGEAR Arlo Q Plus Manuale utente

NETGEAR

NETGEAR Arlo Pro VMS4330-100EUS Manuale utente

NETGEAR

NETGEAR arlo VMS3330-100EUS Manuale utente

NETGEAR

NETGEAR Arlo Q Manuale utente

NETGEAR

NETGEAR VueZone Manuale utente

NETGEAR

NETGEAR Arlo Go Manuale utente

NETGEAR

NETGEAR ARLO PRO Manuale utente

NETGEAR

NETGEAR Arlo Go Manuale utente

NETGEAR

NETGEAR Arlo Q Plus Manuale utente

NETGEAR

NETGEAR Arlo Go Manuale utente

NETGEAR

NETGEAR Arlo Q Plus Manuale utente

NETGEAR

NETGEAR Arlo Q Manuale utente

NETGEAR

NETGEAR VNC4030-111PAS Manuale utente

NETGEAR

NETGEAR Arlo Manuale utente

NETGEAR

NETGEAR Ocuity 100 Manuale utente

NETGEAR

NETGEAR ARLO PRO Manuale utente

NETGEAR

NETGEAR Arlo Q Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente