Nethix WE110 Manuale utente

Manual for gate opener

•1. Overview

•2. Technical characteristics

•3. Pinout and connection

•4. Installation and setup

•4.1. Front panel button

•5. Using the device: APP

•6. Using the device: SMS

•6.1. Administrator

•6.2. Alarm management

2 02/2016

•6.3. Factory reset

•6.4. Miscelaneous commands

•7. Safety guidelines

•8. Warranty and support

•9. Return and repair

1. Overview

WE110 is a SMS and RING based remote control. It provides a digital

input and an output relay that make it suitable for remotely control

gates, doors, windows and in general to automate any access.

Mounting the device is extremely simple thanks to its magnets. Other

mounting options are available.

Read also the WE110 we110_manual_thermostat.

2. Technical characteristics

Characteristic Description

Communications Integrated GSM/GPRS Quad band modem

SIM CARD reader included Provided with

GSM Dual band antenna

Inputs/Outputs 1 dry contact digital input

1 relay output (1A-230VAC)

LED One RGB LED

Button Activates the output relay. Normally used for

opening the gate

3 02/2016

Power supply Low tension 12-24VDC - 9-32VDC

Consumption Average 100mA, transmitting 400mA, max

pulsed 1,8A

Size (L x W x H) 40 x 23 x 85mm

Weight 52 gr

Storage

temperature -25°C - +85°C

Working

temperature -15°C - +55°C

Humidity 0% - 80% (non condensing)

3. Pinout and connection

PIN Description

1 Relay B

2 Relay A

3 Power source VAC1

4 Power source VAC2

4 02/2016

5 Input

6 GND

7 SIM card slot

8 LED

9 Button

4. Installation and setup

•Disable the PIN for the SIM card to be used in the WE110, using

a standard GSM cell phone. Refer to the phone user manual for

details.

• Insert the SIM card in the slot.

• Connect the output relay to the controlled gate or device.

•Screw the antenna provided in the SMA RF connector, then

connect power leads and power on the device.

System startup takes approximately 45 seconds, during which the

LED in the front side show diagnostic information as detailed in the

following table:

LED status at boot time

LED color Status Descriprtion

Fast blinking,

each 0.320s The WE110 is booting

Turned-on for 5

seconds, then

it will reboot

Network registration

error or SIM error

5 02/2016

Fast blinking

for 3 seconds From this moment, the

WE110 is fully

operative

LED status at normal operation

There are two normal conditions that are shown with two different LED

status

• The system LED (green)

• The signal LED (red or blue)

System LED

LED color Status Descriprtion

Turned-on The relay is closed

Turned-off The relay is opened

Signal LED

LED color Status Descriprtion

Turned-on The signal is good

Slow blinking,

each 0.60s The signal is sufficient

Slow blinking,

each 0.60s The signal is not good

For example if the relay is closed and there is a sufficient signal, the

LED status will blink in the following way:

6 02/2016

All setup and control activities of the device are carried out sending

and receiving SMS messages.

Note

The text in bold denotes strings to be typed and sent to the

device.

For example, ADD means that a SMS containing the word ADD

will be sent to the device.

The first operation to execute in a new WE110 is to define the

administrator phone number:

ADMIN +391112223333

From this moment it will be possible to configure WE110 by sending

SMS from only the ADMIN number.

Set the SMS service center of the SIM provider:

CENTER +393359609600

The following table shows the service center numbers of the most

relevant providers:

SMS service center numbers

Country Operator Number

7 02/2016

Italy TIM +39335960960

Italy Vodafone +39349200020

Italy Wind +39320585850

Now it is possible to add a user that will be enabled to call WE110:

ADD +391112223333

Adding two or more users can be done with the same command and

up to ten users can be added. Notice the space between the numbers:

ADD +391112223333 +394445556666

Similarly, it is possible to remove a user from WE110:

CANC +391112223333

Removing two or more users can be done with the same command

and up to ten users can be removed. Notice the space between the

numbers:

CANC +391112223333 +394445556666

Note

Only the administrator user can add or remove users

At any moment the administrator can obtain the list of registered

users:

LIST 1

With this command the administrator receives one SMS with the first

ten users.

8 02/2016

To receive the users 11 to 20, the administrator can send the

command:

LIST 2

and so on with the next users.

4.1. Front panel button

The button located in the front panel, when pressed for 3 seconds,

activates the relay.

5. Using the device: APP

The easiest way to program and use WE110 is by downloading the

app:

The app provides a configuration wizard and an user-friendly interface:

9 02/2016

10 02/2016

Indice

Altri manuali Nethix Termostato

Nethix

Nethix Xilon Lite Manuale utente

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente