Netstor NS372TB3 Manuale utente
3Go Top ↑
1. Unpack the NS372TB3
2. Storage Enclosure Description
2.1 Panel Layout
The box contains the following items:
。Netstor NS372TB3 storage
。Thunderbolt 3 cable (1 meter) × 1
。Power cord × 1
2. Fan LED
。Green – normal
。Red – fan failure (low frequency of RPM or stop)
3. Temperature LED
。Green – normal
。Red – over 50℃
1. Mute Button
。Mute Buzzer Beeping
5Go Top ↑
2.2 Environmental Control Board LED Status
D2 LED: fan failure indicator
。D2 LED no light: both blower fan 1 and 2 are normal
。D2 LED red light: either blower fan 1 or 2 fails
D4 LED: fan 1 status
。D4 LED no light: blower fan 1 is normal
。D4 LED red light: blower fan 1 fails
D5 LED: fan 2 status
。D5 LED no light: blower fan 2 is normal
。D5 LED red light: blower fan 2 fails
Normal
Example:
Fan 1 fails Fan 2 fails
7Go Top ↑
3. Firstly, take the first drive slot for instance: there are two 5.25” bay covers attached
to the front of the storage enclosure. Use a screwdriver to unscrew the two screws
on each cover to detach it from the front panel.
4. Inside the enclosure, there are two sets of metal side brackets for each LTO tape drive.
(a) Detach the first set of metal side brackets by loosening the screws.
(b) From the front panel, insert the LTO tape drive into the enclosure.
8Go Top ↑
(c) As the tape drive is inserted, attach the set of metal side brackets back to the
original position, and fasten the screws on the metal side brackets. Note there
are two bosses on each bracket; have the two bosses be inserted into the screw
holes on tape drive’s side.
5. From inside the NS372TB3 enclosure, connect the first SFF-8482 connector,
labeled P1, to the rear of LTO tape drive for data signal and power source.
※ Repeat the above steps 3 and 5 for the installation of the second LTO tape
drive in the storage enclosure.
P1
LTO Drive
LTO Drive
10 Go Top ↑
4. Blower Fan Speed Adjustment
1. There are two hot-swappable 75×75×28 mm blower fans for ventilation at
rear of NS372TB3. After loosening the two thumbscrews on the fan module,
the blower fan can be pulled out of the storage enclosure.
2. The rear 75×75×28 mm blower fan speed can be adjusted. As the blower
fan module is pulled out, there are four sets of jumpers labeled with 6V,
8V, 10V, 12V from top to bottom on the fan connector board. The default
setting is the jumper being placed over pin 7 and 8 for label 6V for slowest
speed. The speed increases from label 8V to label 12V. As jumper is not
placed over pins, the fan will spin at 12V full speed.
6V
8V
10V
12V
Indice
Altri manuali Netstor Allegato
Netstor
Netstor NA211TB Manuale utente
Netstor
Netstor NS722TB3 Manuale utente
Netstor
Netstor TurboBox Xtreme Manuale utente
Netstor
Netstor NS780S-G3 Manuale utente
Netstor
Netstor NS780TB3 Manuale utente
Netstor
Netstor NA341TB3 Manuale utente
Netstor
Netstor TurboBox Xtreme NA265A Manuale utente
Netstor
Netstor TurboBox Pro NA250A Manuale utente
Netstor
Netstor HercuLes HL23T-PRO Manuale utente
Netstor
Netstor 6Gb/s SAS JBOD Manuale utente
