Netvox R712 Manuale utente

Model：R712

Wireless Outdoor Temperature And Humidity Sensor

Wireless Outdoor Temperature

and Humidity Sensor

User Manual

This document contains proprietary technical information which is the property of

NETVOX Technology. It shall be maintained in strict confidence and shall not be

disclosed to other parties, in whole or in part, without written permission of NETVOX

Technology. The specifications are subject to change without prior notice.

Table of Content

1. Introduction.................................................................................................................2

2. Appearance..................................................................................................................3

3. Main Features .............................................................................................................4

4. Set up Instruction........................................................................................................5

5. Data Report.................................................................................................................6

6. Installation and Precaution .......................................................................................10

7. Important Maintenance Instruction ..........................................................................13

1. Introduction

R712 is a long-range wireless outdoor temperature and humidity device based on the LoRaWAN

open protocol (Class A).

The R712 is mainly used to detect the temperature and humidity in outdoor air, and also carrying a

waterproof housing. It collects data over LoRa network and sends it to devices to be shown, fully

compatible with LoRaWAN protocol.

LoRa Wireless Technology:

LoRa is a wireless communication technology dedicated to long distance and low power

consumption. Compared with other communication methods, LoRa spread spectrum modulation

method greatly increases to expand the communication distance. Widely used in long-distance,

low-data wireless communications. For example, automatic meter reading, building automation

equipment, wireless security systems, industrial monitoring. Main features include small size, low

power consumption, transmission distance, anti-interference ability and so on.

LoRaWAN:

LoRaWAN uses LoRa technology to define end-to-end standard specifications to ensure

interoperability between devices and gateways from different manufacturers.

2. Appearance

Indicator

Temperature and humility probe

Function Key

Waterproof Housing

3. Main Features

⚫Compatible with LoRaWAN

⚫2 section 1.5V AA Alkaline battery

⚫Temperature and humidity detection

⚫IP rating IP43

⚫Compatible with LoRaWANTM Class A

⚫Frequency hopping spread spectrum

⚫Configuration parameters can be configured via a third-party software platform, data can be read

and alerts can be set via SMS text and email (optional)

⚫Applicable to third-party platforms: Actility/ThingPark, TTN, MyDevices/Cayenne

⚫Improved power management for longer battery life

⚫Battery Life*2:

⁻Please refer to web: http://www.netvox.com.tw/electric/electric_calc.html

⁻At this website, users can find battery life time for variety models at different

configurations.

1. Actual range may vary depending on environment.

2. Battery life is determined by sensor reporting frequency and other variables.

4.Set up Instruction

On/Off

Power on

Insert 2 section AA 1.5V batteries

Turn on

Press the function key till the green and red indicator flashes once.

Turn off

(Restore to factory setting)

Press and hold the function key for 5 seconds till green indicator flashes for 20

times.

Power off

Remove Batteries.

Note

1. Remove and insert the battery; the device is at off state by default.

2. On/off interval is suggested to be about 10 seconds to avoid the interference

of capacitor inductance and other energy storage components.

3. Hold the function key and insert batteries, the device will be into engineering

test mode.

Network Joining

Never joined the network

Turn on the device to search the network to join.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Had joined the network

(not at factory setting)

Turn on the device to search the previous network to join.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Function Key

Press and hold for 5

seconds

Restore to factory setting / Turn off

The green indicator flashes for 20 times: success

The green indicator remains off: fail

Press once

The device is in the network: green indicator flashes once and sends a report

The device is not in the network: green indicator remains off

Sleeping Mode

The device is on and in the

network

Sleeping period: Min Interval.

When the reportchange exceeds setting value or the state changes: send a data

report according to Min Interval.

Low Voltage Warning

Low Voltage

2.4V

5. Data Report

Data report configuration and sending period are as following:

Min Interval

(Unit:second)

Max Interval

(Unit:second)

Reportable Change

Current Change≥

Reportable Change

Current Change＜

Reportable Change

Any number

between 1~65535

Any number

between 1~65535

Can not be 0.

Report

per Min Interval

Report

per Max Interval

The device will immediately send a version packet report along with an uplink packet including

temperature, humidity and battery voltage.

The device sends data in the default configuration before any configuration is done.

Default setting:

MaxTime:Max Interval = 60 min=3600s

MinTime:Min Interval = 60 min =3600s

BatteryChange: 0x01 (0.1V)

TemperatureChange:0x0064 (1℃)

HumidityChange:0x0064 (1%)

Note:

The device report interval will be programmed based on the default firmware which may vary.

The interval between two reports must be the minimum time.

Example of Report configuration

FPort：0x07

Bytes

Var(Fix =9 Bytes)

CmdID

DeviceType

NetvoxPayLoadData

CmdID–1 bytes

DeviceType–1 byte –Device Type of Device

NetvoxPayLoadData–var bytes (Max=9bytes)

（1）Command Configuration:

MinTime = 1min、MaxTime = 1min、BatteryChange = 0.1v、TemperatureChange = 1℃、

HumidityChange = 1%

Downlink：0101003C003C0100640064 003C(Hex) = 60(Dec) ,0064(Hex) = 100(Dec)

Response：

8101000000000000000000（Configuration success）

8101010000000000000000（Configuration failure）

（2）Read Configuration:

Downlink：0201000000000000000000

Response：

8201003C003C0100640064（Current configuration）

Description

Device

CmdID

Device

Type

NetvoxPayLoadData

Config

ReportReq

R712

0x01

MinTime

(2bytes Unit:s)

MaxTime

(2bytesUnit:s)

Battery

Change

(1byte

Unit:0.1v)

Temperature

Change

(2byte

Unit:0.01℃)

Humidity

Change

(2byte

Unit:0.01%)

Config

ReportRsp

0x81

Status

(0x00_success)

Reserved

(8Bytes,Fixed 0x00)

ReadConfig

ReportReq

0x02

Reserved

(9Bytes,Fixed 0x00)

ReadConfig

ReportRsp

0x82

MinTime

(2bytes Unit:s)

MaxTime

(2bytes Unit:s)

Battery

Change

(1byte

Unit:0.1v)

Temperature

Change

(2byte

Unit:0.01℃)

Humidity

Change

(2byte

Unit:0.01%)

Example for MinTime/MaxTime logic:

Example#1 based on MinTime = 1 Hour, MaxTime= 1 Hour, Reportable Change i.e.

BatteryVoltageChange=0.1V

MaxTime MaxTime

Sleeping(MinTime) Sleeping(MinTime)

Note: MaxTime=MinTime. Data will only be report according to MaxTime (MinTime) duration

regardless BatteryVoltageChange value.

Example#2 based on MinTime = 15 Minutes, MaxTime= 1 Hour, Reportable Change i.e.

BatteryVoltageChange= 0.1V.

MaxTime

Sleeping(MinTime) sleeping sleeping sleeping

0H 15th M 30th M 45th M 1H

Wakes up and

collects data

3.0V

Does not report

Wakes up and

collects data

3.0V

Does not report

Wakes up and

collects data

3.0V

Does not report

Wakes up and

collects data

REPORTS 3.0V

Wakes up and

collects data

REPORT 3.0V

Wake up and collects data

REPORTS 3.0V

Wakes up and collects data

REPORTS 3.0V

Wakes up and collects data

REPORTS 3.0V

Example#3 based on MinTime = 15 Minutes, MaxTime= 1 Hour, Reportable Change i.e.

BatteryVoltageChange= 0.1V.

MaxTime

sleeping sleeping ...

0H 15th M 30th M 45th M 1H 1H 10th M 1H 25th M

1H 40th M 1H 55th M 2H 10th M

Notes :

1) The device only wakes up and performs data sampling according to MinTime Interval.

When it is sleeping, it does not collect data.

2) The data collected is compared with the last data reported. If the data variation is greater

than the ReportableChange value, the device reports according to MinTime interval. If the

data variation is not greater than the last data reported, the device reports according to

MaxTime interval.

3) We do not recommend to set the MinTime Interval value too low. If the MinTime Interval is

too low, the device wakes up frequently and the battery will be drained soon.

4) Whenever the device sends a report, no matter resulting from data variation, button pushed

or MaxTime interval, another cycle of MinTime/MaxTime calculation is started.

Wakes up and

collects data

REPORTS 3.0V

Wakes up and collects data

2.9V |2.9-3.0|=0.1

REPORTS 2.9V

Wakes up and

collects data

2.9V

Does not report

Wakes up and

collects data

2.9V

Does not report

Wakes up and

collects data

2.9V

Does not report

Wakes up and

collects data 2.9V

Does not report

Wakes up and

collects data

3.0V

Does not report

Users push the button,

REPORTS 2.9V.

Recalculate MaxTime.

Altri manuali per R712

Indice

Altri manuali netvox Accessori

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente

netvox R712 Manuale utente

Manuali Accessori popolari di altre marche