Network Technologies Incorporated VOPEX Series Manuale utente

MAN415 Rev Date 10/13/2022

VOPEX-C64K18GB-4HDBT

4K 18Gbps HDMI HDBaseT Splitter/Extender

via CAT6/6a/7: 4-Port

Installation and Operation Manual

VOPEX®Series

VOPEX-C64K18GB-4HDBT Local Unit (Back) and

Four Remote Units (Included)

TRADEMARK

VOPEX and the NTI logo are registered trademarks of Network Technologies Inc in the U.S. and other countries. All other brand

names and trademarks or registered trademarks are the property of their respective owners.

retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.

CHANGES

The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the

right to make changes in the product design without reservation and without notification to its users.

TABLE OF CONTENTS

Introduction......................................................................................................................................................................1

What is Included..............................................................................................................................................................2

Features and Functions...................................................................................................................................................3

Application Example........................................................................................................................................................6

Cascaded VOPEXs .....................................................................................................................................................7

IR Pin Definitions.............................................................................................................................................................8

EDID Modes....................................................................................................................................................................9

ASCII Commands..........................................................................................................................................................10

ASCII Commands Continued.....................................................................................................................................11

ASCII Commands Continued.....................................................................................................................................12

ASCII Commands Continued.....................................................................................................................................13

Technical Specifications................................................................................................................................................14

Warranty Information.....................................................................................................................................................15

NTI 4K 18Gbps HDMI HDBaseT Splitter Extender via CAT6/6A/7: 4-Port

INTRODUCTION

The VOPEX® 4K 18 Gbps HDMI HDBaseT Splitter/Extender simultaneously distributes uncompressed Ultra-HD 4Kx2K@60Hz

4:4:4 HDMI video, multi-channel audio, RS232, and IR from one video source to up to four displays and speakers, each located

up to 394 feet away via CAT6/6a/7 cable using HDBaseT technology.

The VOPEX-C64K18GB-4HDBT system consists of a 4K HDMI HDBaseT broadcast unit, which connects to the HDMI source and

also supplies video to a local display via the HDMI loop output; and four included receivers for each remote 4K HDMI display and

speakers. The units are interconnected by CAT6/6a/7 cable.

Transmits an uncompressed HDMI signal over one CAT6/6a/7 cable to multiple display locations.

oExtend Ultra-HD 4Kx2K@60Hz 4:4:4 to 394 feet (120 meters).

oExtend 1080p and 1920x1200 to 443 feet (135 meters).

oZero latency.

Supports Ultra-HD 4Kx2K resolutions (4096x2160 and 3840x2160@30/60Hz YUV 4:4:4), HDTV resolutions to 1080p,

and up to 1920x1200 (WUXGA).

HDMI features supported:

oHDMI 2.0 compliant.

oUp to 36-bit Deep Color

oLPCM, Dolby Digital, Dolby TrueHD, DTS-HD, and DTS

oRGB, YCbCr 4:4:4, YCbCr 4:2:2, and YCbCr 4:2:0

oBandwidth up to 18 Gbps

o3D

oHDR10

HDCP 2.2/1.4 compliant.

Supports the DDC2B protocol.

Includes four receivers.

oNo power supply required for the receivers

Full Infrared Remote (IR) control of HDMI source or display. IR transport channel can be forward or backward per the

installation.

RS232 for configuration and control, pass-through, and firmware updates.

oSupports RS232 pass-through from transmitter to receiver or from receiver to transmitter.

oBaud rate: 115200 bps

Built-in EDID table.

Cascade units together to send video simultaneously to many receivers.

Mounting brackets included for easy surface/wall mounting.

Ideal for digital signage, tradeshows, or classrooms where high quality video on multiple displays is needed.

NTI 4K 18Gbps HDMI HDBaseT Splitter Extender via CAT6/6A/7: 4-Port

WHAT IS INCLUDED

Materials supplied with this kit:

1x 4-port HDbaseT splitter

4x HDBaseT receivers

5x IR emitters

5x IR receivers

5x 3-pin Phoenix connectors for RS232

1x 5-pin Phoenix connector for audio

1x 100 - 240VAC@50/60Hz; 24V/2.7A DC Locking Power Adapter (The Transmitter powers all Receivers)

URL Slip with path to this manual

Cables available (not supplied):

Interface cables between the video source/display and the transmitter/receiver are required for proper operation.

Supports cable lengths to 20 feet for 4K resolutions and lengths to 50 feet for 1080p@60Hz using passive HDMI

cables.

Use HD-xx-MM cable to connect an HDMI source or display.

Use HD-ACT-xx-MM 4K HDMI Active Cables to connect a 4K@60Hz HDMI source and/or display up to 50 feet.

Use USB3C-HD4K-xx-MM to connect a 4K@60Hz computer with USB Type C connector up to 10 feet.

Use DVI-HD-xM-MM to connect a DVI computer up to 5 meters.

Supports resolutions to 1080p.

Use CAT6/6a/7 solid or stranded straight through cable for TIA/EIA-568B wiring terminated with standard RJ45 connectors.

Cables not included.

where:

xx is the length of the cable in feet

MM indicates male-to-male connectors

Cables can be purchased from Network Technologies Inc by calling (800) 742-8324 (800-RGB-TECH) in the US and Canada or

(330) 562-7070 (worldwide).

NTI 4K 18Gbps HDMI HDBaseT Splitter Extender via CAT6/6A/7: 4-Port

FEATURES AND FUNCTIONS

Transmitter (Front View)

# LABEL CONNECTOR/LED DESCRIPTION

1 POWER (SYMBOL) LED When the device is powered on, the red power LED will

be illuminated.

2 IN LED When the HDMI IN port connects an active source device,

the green LED will be illuminated.

3 LOOP LED When the HDMI LOOP OUT port connects an active

display device, the green LED will be illuminated.

4 OUT 1-4 LEDs When the HDBT OUTPUT port connects an HDBaseT

Receiver, the corresponding green OUT LED will be illuminated.

NTI 4K 18Gbps HDMI HDBaseT Splitter Extender via CAT6/6A/7: 4-Port

Transmitter (Rear View)

# LABEL CONNECTOR/LED DESCRIPTION

1 RS232 3-Terminal Block Connect screw terminals to a PC or control system via a 3-terminal

block for three functions:

1- Firmware update;

2- Control the Splitter via RS-232 commands;

3- RS-232 signal pass-through (from transmitter to receiver or from

receiver to transmitter).

2 IN 3.5mm Jack Connect to IR receiver cable, the IR receive signal will

emit to “IR OUT” port of the HDBaseT Receiver.

3 OUT 3.5mm Jack Connect to IR blaster cable, the IR emit signal is from “IR IN” port of

the HDBaseT Receiver.

4 AUDIO OUT

COAX + L/R Terminal block &

BNC Female Coaxial/balanced digital audio output port, connect to amplifier or

speaker.

5 On/Off LED Press this switch to power ON/OFF the device.

6 EDID DIP Switch Used to set EDID mode. Please refer to Section “6. EDID

Mode” for details.

IN: connect to HDMI source device such as DVD or set-top box with

an HDMI cable.

7 HDMI HDMI Female

LOOP OUT: connect to the HDMI display device such as TV or

Monitor with an HDMI cable

8 HDBT OUTPUT 1~4 LEDs Connect to the HDBT IN port of the HDBaseT receiver

with a CAT6/6a/7 cable.

9 NONE Green LED Illuminated solid: Transmitter and Receiver are in good connection

status.

Flashing: Transmitter and Receiver are in poor connection status.

Dark: Transmitter and Receiver are not connected

10 NONE Amber LED Illuminated: HDMI Signal with HDCP

Flashing: HDMI Signal without HDCP

Dark: No HDMI Signal

11 DC24V Power Jack Plug the DC 24V power supply into the unit and connect

the adaptor to an AC outlet. (Note: The transmitter powers all of the

receivers via CAT6/6a/7 cables.)

NTI 4K 18Gbps HDMI HDBaseT Splitter Extender via CAT6/6A/7: 4-Port

Receiver (Front and Rear View)

# LABEL CONNECTOR/LED DESCRIPTION

1 POWER (SYMBOL) LED Illuminates ON when power is ON

2 SERVICE USB Micro Type B Used for firmware update (none available at this time)

3 DC24V Power Jack The HDBaseT receiver is powered by the transmitter via a CAT6/6a/7

cable. This jack is not used in this application.

4 HDBT IN RJ45 Female Connect to an HDBT OUTPUT port (1~4) on the transmitter with a

CAT6/6a/7 cable.

5 NONE Green LED Illuminated: Transmitter and Receiver are in good connection status.

Flashing: Transmitter and Receiver are in poor connection status.

Dark: Transmitter and Receiver are not connected

6 NONE Amber LED Illuminated: HDMI Signal with HDCP

Flashing: HDMI Signal without HDCP

Dark: No HDMI Signal

7 HDMI OUT HDMI Female HDMI output port, connect to HDMI display device such as TV or

Projector with an HDMI cable.

8 AUDIO OUT 3.5mm Jack Audio output port, connect to amplifier or speaker.

9 IR IN 3.5mm Jack Connect to the IR Receiver cable. The IR signal will send to the IR

OUT port of the transmitter.

10 IR OUT 3.5mm Jack Connect to the IR blaster cable, the IR signal is from IR

IN port of the transmitter.

11 RS232 3-Terminal Block Screw terminals for RS232 command transmission

RS-232 signal will pass-through (from transmitter to receiver or from

receiver to transmitter).

NTI 4K 18Gbps HDMI HDBaseT Splitter Extender via CAT6/6A/7: 4-Port

APPLICATION EXAMPLE

NTI 4K 18Gbps HDMI HDBaseT Splitter Extender via CAT6/6A/7: 4-Port

Cascaded VOPEXs

For an application where more displays need to be viewed, the VOPEX can be cascaded for connection to more Receivers with

zero latency.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Network Technologies Incorporated Estensione

Network Technologies Incorporated

Network Technologies Incorporated ST-FO4K18GB-RS-LC Manuale utente

Network Technologies Incorporated

Network Technologies Incorporated XTENDEX Series Manuale utente

Network Technologies Incorporated

Network Technologies Incorporated ST-C6USB4K-HDBT Manuale utente

Network Technologies Incorporated

Network Technologies Incorporated XTENDEX Series Manuale utente

Network Technologies Incorporated

Network Technologies Incorporated VOPEX-C64K10GB-4HDBT Manuale utente

Network Technologies Incorporated

Network Technologies Incorporated ST-C6FOUSB4K-LC Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente