Network Flashlink FR-2RU-10-2 Manuale utente

network-electronics.com

Flashlink 2U frame

Rev. 8

Flashlink User Manual

FR-2RU-10-2

FR-2RU-10-2 Rev. 8

Network Electronics ASA

Thorøya

P.O. Box 1020

Sandefjord, Norway

Phone: +47 33 48 99 99

Fax: +47 33 48 99 98

E-mail: [email protected]

www.network-electronics.com

Service Phone: +47 90 60 99 99

Revision history

Current revision of this document is the uppermost in the table below.

Revision Replaces Date Change description

8 7 2007-10-26 New front page and removed old logo.

7 6 2007-09-12 Added Materials Declaration and EFUP; updated EC

Declaration of Conformity.

6 5 27/04/05 NBS: Re-arranged and corrected Chapters, etc.

5 4 07/05/03 RS: Included the control protocol

4 3 25/03/03

RS: Corrected printing errors in Chapter 2.1, added

GPI information and product designations,

shortened fiber optics chapter.

3 2 12/04/02 NBS: Corrected Figure 6 (Chapter 3.4).

2 1 10/07/01 NBS: Changed AURORA to GYDA

1 0 21/12/00

RS: New laser classification, new silk screen on

connector module (fig. 2), corrected address

setting of sub-rack module (swapped 0 and 1 in fig.

0 A 15/12/00

NBS: Renamed Optronics to Electronics & Rev.

Control

A - 23/06/00 RS: Initial Revision

FR-2RU-10-2 Rev. 8

Contents

Revision history............................................................................... 2

1 Product overview......................................................................... 5

2 Specifications .............................................................................. 6

2.1 General specifications ..................................................................................6

2.2 Front view ...................................................................................................6

2.3 Rear view.....................................................................................................6

3 Configuration .............................................................................. 7

3.1 Address setting on each sub-rack.................................................................7

4 Connections ................................................................................ 8

4.1 Power connection........................................................................................8

4.1.1 Pin-out DC1 and DC2 (DB9) 8

4.1.2 GPI Power Supply Status outputs 9

4.2 RS-422 connection ......................................................................................9

4.2.1 Pin-out RS-422 (RJ45) 9

4.2.2 Connecting several sub-racks together 9

5 Sub-rack operation .................................................................... 11

5.1 Removing the front panel ..........................................................................11

5.2 Back plane insertion...................................................................................12

5.3 Card insertion............................................................................................14

5.4 Card removal.............................................................................................16

5.5 Adding new module cards.........................................................................17

5.6 Attaching the front panel ..........................................................................18

6 Fiber optics................................................................................ 20

6.1 Handling of optical fibres...........................................................................20

6.2 Fiber-optic Connector................................................................................21

6.3 Laser safety precautions.............................................................................22

7 flashlink®control protocol.......................................................... 23

7.1 Document conventions .............................................................................23

7.2 Hardware interface ....................................................................................23

7.3 Addressing.................................................................................................23

7.4 General command structure ......................................................................23

7.5 Card detection (hot swap).........................................................................24

7.6 Hello command.........................................................................................24

7.7 Electrical to optical converters ...................................................................24

7.7.1 Hello command 24

7.7.2 Info command 24

7.8 Optical to electrical converters ..................................................................25

7.8.1 Hello command 25

7.8.2 Info command 25

FR-2RU-10-2 Rev. 8

General environmental requirements for flashlink®equipment ...... 26

Product Warranty ......................................................................... 27

Materials declaration .................................................................... 28

Environmentally-friendly use period.............................................. 28

Recycling information................................................................... 29

EC Declaration of Conformity ....................................................... 30

FR-2RU-10-2 Rev. 8

1Product overview

The FR-2RU-10-2, hereafter called "sub-rack", is a compact sub-rack frame,

providing space for up to 10 flashlink®modules of any combination, in

addition to two fixed positions for power supply modules.

The sub-rack features maximum flexibility as every module comes with a

suitable back-plane module, which takes up n x 7TE spacing. This means that

any combination of all modules can be fitted into the sub-rack, or expanded /

rebuilt in the future, when other functionality is needed. Each sub-rack has an

address setting available through DIP-switches on the rear, for use in

combination with the GYDA-SC Rack System Controller card.

FR-2RU-10-2 Rev. 8

2Specifications

2.1 General specifications

AC Power: PWR-AC15/15/5/5V

AC power supply module 100-260 VAC.

DC Power (optional): PWR-DC15/15/5/5V

DC power supply module 36-72 VDC.

Redundant Power

(optional):

PWR-AC15/15/5/5V or

PWR-DC15/15/5/5V.

Dimensions: 483 x 88 x 178 mm (19”, 2RU).

Card slots: 10.

Power Supply slots

(reserved):

Internal voltages: +5V, -5V, +15V, -15V.

2.2 Front view

The front view of the sub-rack shows status LEDs for each module that is

included in the sub-rack + two green LEDs for the power supply modules.

Figure 1: LEDs in front of the flashlink sub-rack.

The uppermost LED of each module card is a "general status" LED.

-Green light means that the card is OK.

-Red light means that the card is faulty.

-No light means that the power is not switched on.

The meaning of each LED on the module cards is described in their respective

manuals.

2.3 Rear view

Figure 2 shows an example of a fully equipped flashlink sub-rack, seen from

the rear side.

To the left is the connector module for the power supply delivered with the

sub-rack. The other connector modules are described in their respective user

manuals.

Figure 2: Example of fully equipped flashlink sub-rack.

FR-2RU-10-2 Rev. 8

3Configuration

3.1 Address setting on each sub-rack

Each sub-rack can be assigned an address through the DIP-switches on the

rear. Maximum 8 sub-rack addresses are available.

This address setting only applies when the sub-rack is used in combination

with a GYDA-SC Rack System Controller.

If you have more than 8 sub-racks together, you need several GYDA-SC Rack

System Controller cards.

The setting of the address of a sub-rack is as follows:

1 0

0means switch to the right (OFF)

1means switch to the left (ON)

SW 4 SW 2 SW 1 Address

OFF OFF OFF 0

OFF OFF ON 1

OFF ON OFF 2

OFF ON ON 3

ON OFF OFF 4

ON OFF ON 5

ON ON OFF 6

ON ON ON 7

Default address is 0.

The GYDA-SC Rack System Controller automatically detects the position of the

cards within each sub-rack.

More detailed information on the RS-422 configuration can be found in a

separate document and at our web site:

http://www.network-electronics.com/

Note!

In order to ensure proper operation of the system, it is

important that no sub-racks controlled by the same

GYDA-SC Rack System Controller card have the same

address set.

Reset the sub-rack after reconfiguring the sub-rack system,

by turning the power off and on again.

FR-2RU-10-2 Rev. 8

4Connections

4.1 Power connection

Figure 3 shows the power connections of the sub-rack as well as the RS-422

connections and the DIP-switches for address setting of the sub-rack.

Figure 3: Connector module for the power supply.

AC: Connect mains to the sub-rack with a mains cord with an IEC 320

connector.

DC: Connect the DB9 male connector from the external DC power supply to

the main unit. Tighten the screws to ensure a proper contact. The DC inputs

have the same function; the left input (DC1) is for the left power module

when seen from the rear and DC2 is for the right power module when seen

from the rear.

4.1.1 Pin-out DC1 and DC2 (DB9)

The maximum current drawn from each pin of the DB9 connector is 2,5A.

Pin #1 GND for DC

Pin #2 +5V Output, Max. current: 6A

Pin #3 Relay GPI Output, Normally Open

Pin #4 +15V Output, Max. current: 1A

Pin #5 Positive part of 48VDC supply Input

Pin #6 -5V Output, Max. current: 1A

Pin #7 Relay GPI Output, Normally Open

Pin #8 -15V Output, Max. current: 1A

Pin #9 Negative part of 48VDC supply Input

Pin 1, 2, 4, 6 and 8 are common to both DC1 and DC2. (I.e. they are

physically connected).

A green LED will light on the front when the power supply is in operation.

FR-2RU-10-2 Rev. 8

4.1.2 GPI Power Supply Status outputs

The GPI module status outputs can be used for wiring up alarms for third

party control systems.

In case of power failure, pins 3 and 7 will be physically connected (low

impedance), otherwise the connection between pins 3 and 7 will be high

impedance.

4.2 RS-422 connection

At the rear end of the sub-rack is an RS-422 bus. When used in combination

with the GYDA-SC Rack System Controller, up to 8 sub-racks can be

controlled. On the rear end of the sub-rack are DIP-switches where each sub-

rack can be assigned its own address (see figure 3).

The RS-422 interfaces are shown in figure 3.

4.2.1 Pin-out RS-422 (RJ45)

Pin #1 Rx A (+)

Pin #2 Rx B (-)

Pin #3 Tx A (+)

Pin #4 Reserved

Pin #5 Reserved

Pin #6 Tx B (-)

Pin #7 Not Connected

Pin #8 Not Connected

Figure 4: RS-422 pin-out.

4.2.2 Connecting several sub-racks together

Several sub-racks can be connected to each other through the RS-422 ports

on the rear of each sub-rack.

One GYDA-SC controller can control maximum 8 sub-racks.

You start with the sub-rack containing the GYDA-SC Rack System Controller,

and use 1 RS-422 port to loop through to the next.

The last sub-rack connected must be terminated with 110Ωin order to ensure

proper operation. The other port of the rack containing the GYDA-SC

controller must be left open, and cannot be connected to other sub-racks.

Figure 5 shows an example of how to connect 8 sub-racks together as seen

from the rear end. By using the RS-422 interface at the GYDA-SC controller

card, we control 8 sub-racks via one RS-422 bus.

FR-2RU-10-2 Rev. 8

Figure 5: Control of 8 sub-racks with GYDA-SC.

The 110Ωtermination plug used is a standard RJ45 plug with the following

internal wiring:

Figure 6: RS-422 termination.

In the figure above, Pin 1 is connected to Pin 2 with a 110Ωresistor, and Pin 3

is connected to Pin 6 with a 110Ωresistor.

1236

Indice

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente

network Flashlink FR-2RU-10-2 Manuale utente

Manuali Alimentazione elettrica popolari di altre marche