NetworX NX-1700E Manuale di installazione

NX1700EIE03

(Supercedes NX1700EID03)

NetworX Series™

NX-1700E Proximity Card Reader

Installation and Startup

NX-1700E Card Reader

Printed in the United States of America.

These instructions do not purport to cover all details or variations in equipment nor to provide every possible

contingency to be met during installation, operation, and maintenance. If further information is desired or if particular

problems arise that are not covered sufficiently for the purchaser’s purpose, the matter should be referred to GE

Interlogix, Gladewater, Texas, USA.

This document contains proprietary information of GE Interlogix, USA and is furnished to its customer solely to assist

that customer in the installation, testing, operations, and/or maintenance of the equipment described. This document

shall not be reproduced in whole or in part nor shall its contents be disclosed to any third party without the written

approval of GE Interlogix.

Please refer to the current GE Interlogix product catalog for detailed warranty information.

Main 800-727-2339 Technical Support 800-727-2339

Outside the US 903-845-6941 Tech Support Fax 903-845-8409

Main Fax 903-845-6811 Sales & Literature 800-547-2556

Web: www.caddx.com

www.ge-interlogix.com

NetworX™is a trademark of the GE Interlogix companies.

Symbol Legend

Warning

Indicates a procedure, practice, condition, or statement that, if not strictly

observed, could result in personal injury.

* This symbol indicates electrical warnings and cautions.

Caution

Indicates a procedure, practice, condition, or statement that, if not strictly

observed, could result in damage to or destruction of equipment or property.

** This symbol indicates general warnings and cautions.



Note

Indicates an essential or important procedure, instruction, condition, or

statement.



Tip

Indicates a user tip. Provides helpful information that is not normally defined in

regular use, but from an experienced user.



Enter Indicates a key or button should be pressed to enter data.

NX-1700E Card Reader

TABLE OF CONTENTS

I. GENERAL DESCRIPTION...........................................................................................................................................4

II. INSTALLATION AND WIRING ..................................................................................................................................4

III. ENROLLING ...................................................................................................................................................................4

IV. ADDRESSING .................................................................................................................................................................5

V. PROGRAMMING...........................................................................................................................................................5

A. USING THE LED KEYPAD...................................................................................................................................5

Entering the Program Mode..............................................................................................................................................5

Entering the Module Address............................................................................................................................................5

Programming a Location ..................................................................................................................................................6

Exiting the Program Mode:...............................................................................................................................................6

B. USING THE LCD KEYPAD...................................................................................................................................7

C. PROGRAMMING DATA TYPES ..........................................................................................................................7

VI. USER CARDS..................................................................................................................................................................7

Adding One User...............................................................................................................................................................8

Adding Multiple Users with Auto-Increment.....................................................................................................................8

Activate One User (Single User).......................................................................................................................................9

De-Activate One User........................................................................................................................................................9

Delete / Reset One User ....................................................................................................................................................9

VII. PROGRAMMING LOCATIONS ................................................................................................................................10

Location 0 Programming the Scan Functions...............................................................................................10

Location 241 Programming the X-10 Address for the Scan Functions.............................................................10

Location 242 Programming the Options and Reader Partition........................................................................11

Location 243 Programming the Zones..............................................................................................................12

Location 244 Programming the Various Reader Timers ..................................................................................12

Location 245 Resetting the Reader Address......................................................................................................13

Location 246 Programming the Access Options...............................................................................................13

Location 247 Programming the Opening Time for Schedule 1.........................................................................13

Location 248 Programming the Closing Time for Schedule 1..........................................................................14

Location 249 Programming the Days for Schedule 1 .......................................................................................14

Locations 250 - 270 Programming the Schedules 2 - 8 ...............................................................................................14

Location 271 Programming the Date of Holidays in January..........................................................................14

Locations 272 - 282 Programming the Date of Holidays from February to December..............................................15

Location 283 Programming Activation Data for User Cards 1 through 120 ...................................................15

Location 284 Programming Activation Data for User Cards 121 through 240 ...............................................15

VIII. PROGRAMMING WORKSHEETS............................................................................................................................16

IX. ORDERING INFORMATION.....................................................................................................................................22

X. GLOSSARY....................................................................................................................................................................23

XI. FCC INFORMATION...................................................................................................................................................23

XII. UNDERWRITERS LABORATORIES INFORMATION.........................................................................................23

XIII. SPECIFICATIONS........................................................................................................................................................24

NX-1700E Card Reader

I. GENERAL DESCRIPTION

The NetworXNX-1700Eis a proximity cardreader/door control moduleusedto expandthecapabilities oftheNetworX

control panels.

$ Microprocessor-controlled

$ Includes one (1) low current trigger output, which can be used to control a door strike relay

$ Up to 15 card readers can be connected to the NetworX control panel

$ Can be programmed to control access in any or all partitions

$ LEDs can be programmed to follow the output and/or the armed or ready status of the system

$ Has an optional optical tamper switch

II. INSTALLATION AND WIRING

To install the card reader, simply wire it into the system. Refer to the following wiring table for details.

DESCRIPTION

GREEN

(DATA) Connect to the NetworX control panel DATA terminal. This wire is the data-

signaling

terminal to all the devices on the buss.

BLACK

(COM) Connect to the NetworX control panel COMMON

terminal. Supplies the commonsideof

the power to the card reader module.

RED

(POS) Connect to NetworX control panel AUX POWER +

terminal. Supplies power to the card

reader module.

WHITE

(EGRESS)

This is an optional EGRESS

(exit) input. To use this feature, connect the normally open

egress switch between this terminal and COM

. If this feature is not used, there is no

need to connect this wire.

BLUE

(OUTPUT)

This is an optional open-collector (negative trigger) OUTPUT

. It can be used to drive a

relay. To use this feature, connect the coil contacts of a relay between this terminal and

AUX POWER +. Absolute maximum 14 volts @ 25mA.

This is a low current output and must not

be used to directly energize high

current door openers.

III. ENROLLING

The NetworXcontrolpanelshave theabilitytoautomatically findandstore inmemorythe presence ofallkeypads, zone

expanders,wirelessreceivers, output modules,andanyother device onthekeypadbuss. This allows thesedevicesto

be supervised by the control panel. To enroll the devices, enter the Program Mode using the procedure outlined in the

control panel Installation Manual. When the Program Mode is exited, the NX-8 control will automatically enroll the

devices. Theenrollingprocesstakes about 12 seconds,duringwhichtime the ServiceLEDwillilluminate. User codes

will not be accepted during the enrolling process. Once a module is enrolled, if it is not detected by the control, the

Service LED will illuminate.

NX-1700E Card Reader 5

Scan: To

“present” or

pass a card or

FOB within

sensing range

of the card

reader module.

IV. ADDRESSING

Once the reader is wired into the system, the module needs to be addressed. Unlike most

NetworXexpanders,theaddress of anyparticularreader isdeterminedby itselfafterinstallation

is complete. Follow the procedures outlined under the section “PROGRAMMING”. When

prompted to enter the module device number, a card must be scanned at the reader to initiate

addressing (one short beep). When completed (1-2 seconds), the reader will beep back its

address (long beeps). Refer to Table IV-1 that follows for possible addresses.

Table IV-1

Beeps Address Beeps Address

1 113 9 121

2 114 10 122

3 115 11 123

4 116 12 124

5 117 13 125

6 118 14 126

7 119 15 127

8 120

V. PROGRAMMING

A. USING THE LED KEYPAD

ACTION RESULT

ENTERING THE PROGRAM MODE



Enters the Program Mode.

Stay, Chime, Exit, Bypass & Cancel LEDS will

flash.

[Go To Program Code]

Factory Default is 



If the "Go To Program Code" is valid, the "Service"

LED will flash and the 5 function LEDs will

illuminate steady. You are now in the Program

Mode and ready to select the module address.

ENTERING THE MODULE ADDRESS

Scan a card. 

The card reader will address itself.

 #

(example only)



Enters the module address. Refer to Table IV-1 on

page5forthe address assigned bythecardreader

module itself.

The Armed LED will illuminate while it is waiting for

a programming location to be entered.

NX-1700E Card Reader

PROGRAMMING A LOCATION

If an attempt is made to program an invalid entry for a particular segment, the keypad

sounder will emit a triple error beep (beep, beep, beep), and remain in that segment

awaiting a valid entry.

To Enter a Location:

[location] # 

The Armed LED will flash. If the location is valid,

the "Armed" LED will extinguish, the "Ready" LED

will illuminate, and the zone LED’s will show the

data for the first segment of this location.

To Change Location Data:

[changed data] 

The "Ready" LED will flash to indicate a data

changeinprocessand will continueuntilthedatais

saved.



The new data is saved.

The keypad will increment and display the next

segment’s data.

NOTE: Repeat these steps until the last

segment is reached.

To Exit a Location:

# 

Exits from this location. The “Ready” LED will

extinguish.The"Armed"LED will illuminatewaiting

for a new programming location to be entered.

To Review The Data:

[location] # 

The Armed LED will flash. If the location is valid,

the "Armed" LED will extinguish, the "Ready" LED

will illuminate, and the zone LED’s will show the

data for the first segment of this location.



(Do not enter data.)

The next segment is displayed. Each time ris

pressed, the data of the next segment will be

displayed for review.

Shortcuts:

Previous location.

Same location.

Next sequential location.

EXITING THE PROGRAM MODE:

EXIT EXIT 

Exits this programming level.

NX-1700E Card Reader 7

B. USING THE LCD KEYPAD

All steps required for programming are the same as the aforementioned LED keypad. The LCD keypad display will

prompt you for the data required. While in the programming mode, and not in a location, the number in parenthesis is

thelocationyouwere previously changing. For example,ifthe displayreads"Enterlocation,then # (5)",itis reminding

you that location 5 was the last location you programmed. In feature selection data, the numbers of the enabled

features will be displayed. The features not enabled will display a hyphen (-).

C. PROGRAMMING DATA TYPES

a) Numerical Data

Numerical data can take on values from 0-255 or 0-15 depending on the segment size.

b) Feature Selection

Feature selection data is used to turn features on or off.

VI. USER CARDS

Addingandde-activating usersisdone through acombinationof enteringinformationat the keypadand scanningcards.

Before a card can be entered, one reader on the system must be programmed with User Card Programming enabled

(Location 242, Segment 1, Option 1, page 11).

It is recommended that only one reader on the system be enabled to modify user cards and that

this reader be located near a keypad. This reader will transfer information toall other readers in

the system once programming is finished.

Once a reader is enabled to modify users, it must be placed into one of the following five modes:

1) Add One User

2) Add Multiple Users w/ Auto-Increment

3) Activate One User

4) De-Activate One User

5) Delete/Reset One User.

Modifying users on a card reader is similar to modifying user codes at a keypad.

MUST BE A MASTER USER IN ORDER TO MODIFY USER CARD INFORMATION.

ACTION RESULT



Accesses Code Programming

[master code]

Factory Default is 



If the code is valid, the Ready LED will flash.

User Number 2 isused to program usercards, so…

if the control is an NX-4, NX-6,

or NX-8

if the control is an NX-8E



Unit is now ready for you to choose one of the User

Card Programming modes (as if user code 2):

1) Add One User

2) Add Multiple Users (w/ Auto-Increment)

3) Activate Single User

4) De-activate One User

5) Delete / Reset One User

IMPORTANT NOTE

Adding or de-activating user cards from a reader will cause the code for User Number 2 to become invalid.

Therefore, it will need to be re-entered after all user cards are programmed into the readers.

NX-1700E Card Reader

ADDING ONE USER

ACTION RESULT

[STAY] 

Accesses Activation mode

[3-digit user number]

Example: if 4-digit user code

or if 6-digit user codes



If a valid user number is entered, LED1 on any

enabled readers will begin to flash.

Scan the card designated for the user

entered in the previous step.



1) If the user card is not already in the system, it

will be added and mapped to the entered user

number and LED1 will continue flashing

indicating that the next user card can be

scanned for the next user number.

2) If the card is already in the system, the reader

willtriplebeepand LED1 will continueflashing;

the user number is not incremented in this

case.

Continue scanning user cards until the

desired number of cards has been added.



After about 30 seconds without a card being

scanned, all the readers in the system will be

updated with the new user card information.

ADDING MULTIPLE USERS WITH AUTO-INCREMENT

ACTION RESULT

[CANCEL] 

Accesses Activation mode

[3-digit user number]

Example: if 4-digit user code

or if 6-digit user codes



If a valid user number is entered, LED1 on any

enabled readers will begin to flash.

Scan the card designated for the user

entered in the previous step.



3) If the user card is not already in the system, it

will be added and mapped to the entered user

number and LED1 will continue flashing

indicating that the next user card can be

scanned for the next user number.

4) If the card is already in the system, the reader

willtriplebeepand LED1 will continueflashing;

the user number is not incremented in this

case.

Continue scanning user cards until the

desired number of cards has been added.



After about 30 seconds without a card being

scanned, all the readers in the system will be

updated with the new user card information.

 By default, user cards are added and activated. In order to add a user card and

de-activate it at the same time, scan and hold the card to be added until two

beeps are sounded at the reader.

NX-1700E Card Reader 9

ACTIVATE ONE USER (SINGLE USER)

ACTION RESULT

[CHIME] 

Accesses Activation mode

[3-digit user number]

Example: if 4-digit user code

or if 6-digit user codes



If a valid user number is entered, LED1 on any

enabled readers will begin to flash.

Scan any card. 

The card information for the user entered in the

previous step will be activated, and LED1 will stop

flashing. After about 30 seconds, all the readers in

the system will be updated.

DE-ACTIVATE ONE USER

ACTION RESULT

[BYPASS] 

Accesses De-activation mode

[3-digit user number]

Example: if 4-digit user code

or if 6-digit user codes



If a valid user number is entered, LED1 on any

enabled readers will begin to flash.

Scan any card 

The card information for the user entered in the

previous step will be cleared, and LED1 will stop

flashing. After about 30 seconds, all the readers in

the system will be updated.

DELETE / RESET ONE USER

ACTION RESULT

[EXIT] 

Accesses De-activation mode

[3-digit user number]

Example: if 4-digit user code

or if 6-digit user codes



If a valid user number is entered, LED1 on any

enabled readers will begin to flash.

Scan any card 

The card information for the user entered in the

previous step will be cleared, and LED1 will stop

flashing. After about 30 seconds, all the readers in

the system will be updated.

If an individual keeps the

card, it can still be deleted.

ACTIVATING / DE-ACTIVATING / RESETTING USERS

If User Number 0 is entered, the desired function will be performed on the

user associated with the card scanned.

NX-1700E Card Reader

VII. PROGRAMMING LOCATIONS

SCAN METHODS: Legacy mode is default. Alternative mode is shown below in brackets { }.

Refer to Location 242 Segment 1 on page 11, and the Glossary on page 23 for explanation.

LOCATION 0 PROGRAMMING THE SCAN FUNCTIONS

(3 segments of binary data) Location 0 is used to select the particular function(s) that are activated when a card is

scanned.Morethanone function may beselected.Ifmore than onefunctionisselected, they will executeinorderfrom

function 1 to function 8.

Functions 1-6 will be performed based on the user’s authority as programmed by the [] [6] function

(refer to keypad user manual).

Segment 1 Single Scan Function {Single Beep}

Program the functions that are performed when a card is scanned {one beep}.

LED1 - "On" to send Code Entry function to the control panel.

LED2 - "On" to activate the Armed Away mode.

LED3 - "On" to activate the Armed Stay mode.

LED4 - "On" to send the Disarm function to the control panel.

LED5 - "On" to send Auxiliary Function #1 to the control panel.

LED6 - "On" to send Auxiliary Function #2 to the control panel.

LED7 - "On" to broadcast an X-10 function (see Location 241 for programming).

LED8 - "On" to send a Request To Exit (RTE); and activate the onboard open collector output.

(Default is “On”) Location 243, Segment 2 must be programmed with a valid zone number

for the RTE to be sent.

Segment 2 Double Scan Function {Double Beep}

Program the functions that are performed when a card is scanned twice within the 2 Scan Hold Time {two beeps}.

Location 244, Segment 1 programs the length of time between beeps. The descriptions of the options are the same as

for Single Beep Scan Function. Default is 1.

Segment 3 Single Scan Hold Function {Triple Beep}

Program the functions that are performed when a card is scanned and held at the reader for the duration of the 2Scan

HoldTime{threebeeps}. Location 244,Segment1 programs thelengthof timebetweenbeeps. Thedescriptionsof the

options are the same as for Single Beep Scan Function. Default is 1.

LOCATIONS 1 - 240 RESERVED

LOCATION 241 PROGRAMMING THE X-10 ADDRESS FOR THE SCAN FUNCTIONS

(5 segments of numerical data)

Segment 1

Program a number from 0 -15 to represent the corresponding X-10 Module Number from the following table.

Default is 0.

Module

Seg 1 0

Indice

Manuali Lettore di schede popolari di altre marche

Lindy

Lindy 43185 Manuale utente

Lindy

Lindy 43185 Manuale utente

ViziT

ViziT RD-4F Manuale utente

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuale utente

AVID ID

AVID ID AVID1043 Manuale utente

Conrad

Conrad PCMCIA Manuale utente

Rosslare

Rosslare DR-6255 Manuale utente

Lindy

Lindy 51541 Manuale utente

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuale utente

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuale utente

ACS

ACS ACR122L Manuale utente

Secukey

Secukey S2-MF Manuale utente

Elecom

Elecom MR-SMC07 series Manuale utente

Alien

Alien ALR-9800 Manuale utente

ACS

ACS ACR310 Manuale utente

Datamars

Datamars R-IN1300 MID Manuale utente

Alarm Lock

Alarm Lock AL-PRE2 Manuale utente

xpr

xpr B100PROX-AH Guida utente