Newlab L400MD04C1A01 Manuale utente

User Manual L400MD04C1A01

USER MANUAL L400MD04C1A01

SUBJECT INDEX:

DESCRIPTION

TECHNICAL SPECIFICATION

DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE

OPERATION MODES

LINEAR POTENTIOMETER MODE 100KOHM

MODE 0-10V/1-10V (NOT ISOLATED) PASSIVE

PUSH MODE

DALI MODE

BLUETOOTH MODE + PUSH

PARAMETERS CONFIGURATION

1 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

L400MD04C1A01

Mono channel costant current dimmer DALI/PUSH/POT/1-10V/BLE

Monochannel Dimmers with Output Current PWM.

Input Range: 8-53V DC.

Output Current PWM with current from 0.17A to 1.05A (54.6W at 52V DC).

Controllable with Android/iOS app Newlab Go.

In order to set the output current you will need the L392MA00N0A01

interface sold separately. Default current 0.35A.

In order to set the fade output and the logarithmic or linear output you will

need the L392MA00N0A01 interface sold separately, the other working

modes are automatically detected by the device. Please refer to user

manual.

Input Controls

Type Qty

Insulated Push button 1

DALI 1

Linear Potentiometer 100K 1

0-10V Passive 1

1-10V Passive 1

Bluetooth LE 1

TECHNICAL NOTES

- Monochannel Dimmers with Output Current PWM.

- Input Range: 8-53V DC.

- Power 7.35W @ 8V, 11.55W @ 12V, 24.15W @ 24V, 49.35W @ 48V,

54.6W @ 53V.

- The device is not equipped with earth connection

Protection against accidental contact is garantied by the enclosure.

- Power Connector Cross-section of conductors 14-30 AWG (0.05-2.08

mmq).

- Interface Connector Cross-section of conductors 15-30 AWG (0.05-1.65

mmq).

- Output Current PWM with current from 0.17A to 1.05A (54.6W at 52V

DC).

- Input Controls: Insulated Push button x1, DALI x1, Linear Potentiometer

100K x1, 0-10V Passive x1, 1-10V Passive x1, Bluetooth LE x1.

- Notice on 0-10V (1-10V): this control circuits is not insulated, use only

insulated 0-10V(1-10V) source generator.

- PWM Frequency: 390 Hz.

- Thermal foldback: 150 C. Degrees on uC.

- Storage Temperature Min: -40 Max: 60 C. Degrees.

- Working Temperature Min: -20 Max: 50 C. Degrees.

- Printed Circuit UL.

- Protection Class: IP20.

- Weight: 44 gr.

- Standard Dimension 40x80x24.45 mm.

- Dimension with accessories 40x100x24.45 mm.

- Reverse polarity protection.

- Open circuit protection.

- Surge voltage protection.

- Over temperature protection.

- Short circuit protection.

- In order to supply the device you have to use a SELV power supply in

order

to maintain the required elettrical security level

All connections must be made with non-live devices

and carried out by specialized personnel.

2 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

- Use only in dry conditions.

3 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

CODE INPUT

VOLTAGE

(MAX) OUTPUT

CURRENT

N. OUTPUT

CHANNELS

MAX OUTPUT

POWER

CONTROL

INPUTS

CASE DIMENSION

L400MD04C1A01 8-53V DC from 0.17A

to 1.05A

1 54.6W at 52V DC Insulated Push button x1

DALI x1

Linear Potentiometer

100K x1

0-10V Passive x1

1-10V Passive x1

Bluetooth LE x1

YES 40x80

h 24.45

4 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE

POWER SUPPLY CONNECTION DIAGRAM AND LED L400MD04C1A01 - FIGURE N. 1

The L400MD04C1A01 dimmer has to be powered according to the polarity showed in FIG. 1

through the DC IN (+ and -) terminals.

In case the power supply polarity is inverted no damage will be caused to the device .

The LED (LED PWR) positioned on the circuit board indicates the presence of power supply.

The LED (LED DIM) shows the dimming level of the output.

The LED load connection has to be made by using the OUT (L+ and L-) terminals.

5 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

OPERATION MODES

LINEAR POTENTIOMETER MODE 100KOHM

POTENTIOMETER WIRING L400MD04C1A01 - FIGURE N. 2

In order to activate this mode of control/operation just connect a linear potentiometer of 100 Kohm between the D+

and D- inputs and disconnect the remaining inputs.

By default, the dimming curve follows a logarithmic trend proportional to the resistance value set by the

potentiometer.

A resistance value of less than 5 Kohm is interpreted as load off.

The maximum brightness value is reached by exceeding the value of 95 Kohm.

In case the potentiometer is disconnected, the dimmer sets the output to the saved level (see preset level

change).

The preset value is zero by default.

On the first run in this mode it could be necessary to set the input to a value greater than 50% (55K or higher on D-

D + input) in order to configure the dimmer to the potentiometer mode.

*This setting can be configured through the interface cod. L392MA00N0A01

ATTENTION IN THIS MODE THE BLUETOOTH CONTROL IS FORBIDDEN

6 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

MODE 0-10V/1-10V (NOT ISOLATED) PASSIVE

WIRING 0-10V L400MD04C1A01 - FIGURE N. 3

In order to activate this mode of control/operation just connect the active control signal of 0-10V/1-10V between

the D+ and D- inputs (being careful to observe the correct polarity) and disconnect the remaining control signals.

The maximum current absorbed by 0-10V dimmer interface is 0,1 mA.

By default, the dimming curve follows a logarithmic trend proportional to the control voltage. A voltage value of less

than 1V is interpreted as load off.

In case the 0-10V/1-10V signal is disconnected, the dimmer sets the output to the saved level (see preset level

change). The preset value is zero by default.

On the first run in this mode it could be necessary to set the input to a value greater than 50% (5V or higher on D-

D + input) in order to configure the dimmer to the 0-10V/1-10V mode.

*This setting can be configured through the interface cod. L392MA00N0A01

ATTENTION IN THIS MODE THE BLUETOOTH CONTROL IS FORBIDDEN

7 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

PUSH MODE

WIRING BUTTON L400MD04C1A01 - FIGURE N. 4

In order to activate this mode of control/operation it is necessary to remove any control signals from the D + and D-

inputs and connect between the DALI/P1 and DALI/P2 inputs, a signal in direct or alternating voltage

(DC voltage range:10÷265V, AC 12÷265Vac 50÷65Hz) interrupted by a normally open button (N.O.).

No polarization is needed for the input signal.

The maximum current absorbed by the PUSH interface is about 2mA.

The dimmer saves the output position in order to restore the set level in case of power failure (preset).

PUSH interface operation

Single Click (rapid press (<1sec))

- Turns on or off the output (ON/OFF).

Double Click (rapid press (<1sec))

- Sets maximum brightness (output= 100%)

Long Press (long press (>1sec))

- If the dimmer is in OFF position, it sets the output to the minimum value (default= 1%)

- If the dimmer is in ON position, the long press enables the output dimming (up/down).

8 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

DALI MODE

DALI L400MD04C1A01 WIRING - FIGURE N. 5

In order to activate this mode of control/operation it is necessary to shortcircuit the D+ and D- inputs and connect

the DALI bus between the DALI/P1 and DALI/P2 inputs.

On the first reception of a properly formatted DALI package the dimmer is configured in DALI mode. Once

configured in DALI mode and disconnected from the DALI bus the dimmer switches to the POWER ON LEVEL

mode set through DALI bus.

The maximum current absorbed by the DALI bus is about 2mA.

ATTENTION IN THIS MODE THE BLE (Bluetooth) CONTROL IS FORBIDDEN

Below you can find the implemented standard commands:

DIRECT ARC POWER

OFF

DOWN

STEP UP

STEP DOWN

RECALL MAX LEVEL

RECALL MIN LEVEL

STEP DOWN AND OFF

ON AND STEP UP

GO TO SCENE (0-15)

RESET

STORE ACTUAL LEVEL IN THE DTR

STORE THE DTR AS MAX LEVEL

STORE THE DTR AS MIN LEVEL

STORE THE DTR AS SYSTEM FAILURE LEVEL

STORE THE DTR AS POWER ON LEVEL

STORE THE DTR AS FADE TIME

STORE THE DTR AS FADE RATE

STORE THE DTR AS SCENE (0-15)

REMOVE FROM SCENE (0-15)

ADD TO GROUP (0-15)

REMOVE FROM GROUP (0-15)

STORE DTR AS SHORT ADDRESS

QUERY STATUS

QUERY BALLAST

QUERY LAMP POWER ON

QUERY LIMIT ERROR

QUERY RESET STATE

QUERY MISSING SHORT ADDRESS

QUERY VERSION NUMBER

QUERY DEVICE TYPE

9 NEWLAB - User Manual L400MD04C1A01

User Manual L400MD04C1A01

QUERY PHISICAL MINIMUM LEVEL

QUERY POWER FAILURE

QUERY CONTENT DTR1

QUERY CONTENT DTR2

QUERY ACTUAL LEVEL

QUERY MAX LEVEL

QUERY MIN LEVEL

QUERY POWER ON LEVEL

QUERY SYSTEM FAILURE LEVEL

QUERY FADE TIME/FADE RATE

QUERY SCENE LEVEL (0-15)

QUERY GROUPS (0-7)

QUERY GROUPS (8-15)

QUERY RANDOM ADDRESS H

QUERY RANDOM ADDRESS M

QUERY RANDOM ADDRESS L

10 NEWLAB - User Manual L400MD04C1A01

Indice

Altri manuali Newlab Dimmer

Newlab

Newlab L400MC04T1A01 Manuale utente

Newlab

Newlab L458MC04T1A01 Manuale utente

Manuali Dimmer popolari di altre marche

ZooZ

ZooZ ZEN54 LR Manuale utente

Lex

Lex 6KW Manuale utente

DIODE LED

DIODE LED TOUCHDIAL Mini Manuale utente

Viessmann

Viessmann 5590 Manuale utente

American DJ

American DJ DP-8A Manuale utente

Teleco

Teleco TVSTICK868RGB29 Manuale utente

INSTEON

INSTEON LampLinc 2457D2 Manuale utente

LEGRAND

LEGRAND WattStopper RH703PTU Manuale utente

ADB

ADB EURODIM TWIN TECH Manuale utente

Sinope

Sinope DM2550ZB-C4 Manuale utente

SkyLink

SkyLink SK7 Manuale utente

Makel

Makel RC Manuale utente

Lightronics

Lightronics XC-62 Manuale utente

Triton Blue

Triton Blue DM-1225 Manuale utente

ETC

ETC ES750 Istruzioni operative

NA OMEGA + Manuale utente

GE ZB3001 Manuale utente

LSC

LSC DP-1210 Manuale utente