Newland NLS-MT70 Manuale utente
NLS-
Portab
l
User G
MT70
l
e (Bar
c
uide
c
ode) D
a
a
ta Col
l
l
ector
© 2012 by Fujian Newland Auto-ID Tech Co., Ltd. All rights reserved.
Please carefully read the manual before use the product, and effectively to protect the safety of products operation. Please
keep this manual after reading properly and save for the next reading.
Do not disassemble the terminal or tearing the seal label on the terminal. Otherwise, Fujian Newland Auto-ID Tech. Co., Ltd.
does not assume responsibility for the warranty or replacement.
The pictures in this manual are for reference only. If the individual picture from the actual product was different with this manual,
please refer to actual product. Regarding to the product modification and update, Newland Auto-ID Tech. Co., Ltd. reserves the
right to make changes to any software or product to improve reliability, function, or design at any time without notice.
This manual contains all the information is protected by copyright. Any Company and individuals should not in any way or
reason for any form of extract, copy, sell all or part of this document without written permission.
Fujian Newland Auto-ID Tech. Co., Ltd
Newland Science & Technology Park, No.1 Rujiang West Rd., Mawei district, Fuzhou, Fujian, China
Web :http://www.nlscan.com
Table of Contents
Chapter 1 About This Guide ........................................................................................................................................................................... 1
Chapter 2 Getting Started ............................................................................................................................................................................... 4
Chapter 3 Using the MT70 Series.................................................................................................................................................................. 8
Chapter 4 Using WiFi Communication ........................................................................................................................................................ 21
Chapter 5 Accessories................................................................................................................................................................................... 26
Chapter 6 Maintenance& Troubleshooting ................................................................................................................................................. 27
1
Chapter 1 About This Guide
Introduction
This guide provides information about using the NLS-MT70.
Documentation Set
The documentation set for the NLS-MT70 provides information for specific user needs and includes:
NLS-MT70 Series Quick Start Guide ：Describes how to get the NLS-MT70 Series up and running.
NLS-MT70 Series User Guide ：This is the manual, Describes how to use the NLS-MT70 Series.
API Software Development Manual ：Describes how to use API for application development.
WinCE Software Utilities User Guide ：Describes how to use Newland's WinCE utilities software.
Specification
Performance
Processor Marvell XScale PXA310, 806MHz CPU
Operation System Microsoft Windows CE.NET 6.0
Memory
256MB RAM
128MB ROM for system area
2GB flash memory for user storage
Interface RS-232, USB 2.0, support USB charge
Physical
Dimensions (L x W x H) 170.5 x 85 x 54 mm (6.7 x 3.3 x 2.1 inch)
Weight 454g (Including battery)
Display 3.5” QVGA with backlight TFT Touch screen LCD, support sunlight readable
Keyboard 33 Keys Numeric with backlight (QWERTY optional)
Notification Vibrator, Speaker and LED
Battery Main 3.7V, 3300mAh Rechargeable Li-Polymer battery
Backup 3.7V, 150mAh Rechargeable Li-Polymer battery (support 50hours data backup)
Expansion Micro SD memory slot
Power Adaptor Output: DC 5V, ≥1.5A; Input: AC 100~240V, 50~60Hz 0.4A
Environmental
Operation Temperature -10℃to 50℃
Storage Temperature -20℃to 60℃
Humidity 5% ~ 95% (non-condensing)
Drop 1.5 m drop to concrete
Environmental Sealing IP65 sealing
2
Barcode
1D Barcode Laser (≥4 mil) Code128, EAN-13, EAN-8, Code-39, UPC-A, UPC-E, Codabar, Interleaved 2 of
5, ISBN/ISSN, Code 93, etc.
CCD (≥4 mil)
2D Barcode CMOS (≥5 mil) ALL 1D and PDF-417, QR Code, Data Matrix, Maxicode, Aztec, etc.
Wireless
WLAN Summit IEEE 802.11 b/g
Certificates
FCC, CE, CCC
Software Version
Firmware information query tool can detect and display terminal software and hardware version information and helpful
future updates or maintenance.
The firmware information query tool can detect the information:
A. To determine the operation system version.
B. To determine the firmware version.
C. To determine the system configuration, production date and other information.
D. To determine the version of WIFI module, and WIFI MAC addresses.
E. To determine the type and version of barcode engine.
Tap “Start”→“Settings”→“Control Panel”→double clicks “Firmware Information”.
Figure 1.1: Firmware Information
3
Service Information
Newland China
Phone +86-400-608-0591
Newland Europe
Phone +31(0)-345-870-033
Newland Taiwan
Phone +886-2-7731-5388
Newland North America
Phone +1-510-490-3888
4
Chapter 2 Getting Started
Introduction
This chapter lists the parts and accessories for the MT70 Series and explains how to install and charge the batteries, and
power on the MT70 Series for the first time.
Unpacking
Carefully remove all protective material from the pack.
Verify that you received the following:
MT70 Portable (Barcode) Data Collector
USB cable
AC adaptor
Li-Polymer battery
Tethered stylus
Hand strap
Quick Start Guide
Getting Started
Installing the Main Battery
123
45 6
1. Figure 1 indicates the direction to unlock thelatch.
2. Figure 2 indicates the direction to take out the battery cover.
3. Follow the instructions of figure 3 and 4 to insert the battery.
4. Follow the instructions of figure 5 to close down the battery cover.
5. Push the latch to the lock position.
5
Charging the Battery
There are two ways to charge the battery:
Charge the terminal battery via USB connection to PC. Charging time: around 8-10 hours.
Charge the terminal battery via AC adaptor. Charging time: around 4 hours.
Charge the terminal battery at least 8 hours before its first use.
Charging indication: Charging: red LED; Fully Charged: green LED.
Keypads
1 SCAN key Barcode reading button.
2 FUNC key User defined application function keys.
3 SHIFT key To switching upper or lower case letters.
4 TOOL key Pop-up shortcut menu, or perform shortcuts.
5 Backlight key Open or close screen backlight
6 Power key To power on, sleep or wake up the terminal.
7 ALPHA key Alpha or numeric input switching.
Power On, Suspend and Wake Up
Power On:
Long press the power button for 2-3 seconds to start the terminal.
Suspend:
6
During terminal in power on status, long press the power button for 2 seconds to turn terminal into suspend mode
immediately.
Terminal no operation in a period of time will go into suspend mode, when you turn on the auto suspend function.
The timer for automatically into suspend mode can be set by:
Tap “Start”→“Settings”→“Control Panel”→double clicks “Power”→“schemes”.
Wake Up:
During terminal in suspended status, press power button to wake up the terminal.
Calibrating the Screen
The touch screen calibration tool is for setting accuracy of the touch screen.
Tap “Start”→“Settings”→“Control Panel”→double clicks “Stylus”→”Calibration”.
Click “Recalibrate” button then the screen becomes as shown in Figure 2.2.Carefully press and briefly hold the tip of stylus
on the center of each target that appears on the screen. Repeat as the target moves around the screen then tap the
screen to continue.
Figure 2.1: Calibration Figure 2.2: Recalibrate
Checking Battery Statues
To check the charge status of the main battery in the terminal.
Tap “Start”→“Settings”→”System”→double clicks “Power”.
7
Figure 2.3: Power Properties Figure 2.4: Power Properties - Schemes
Power schemes has four status; “Running”, “User Idle”, “System Idle” and “Suspend”:
When user operates on the keypad or taps the touch screen, system is in the running state.
In running state, within the time set in the operating conditions no any operation, system turn to the user idle state.
In user idle state, within the time set in the operating conditions no any operation, system turn to the system idle state.
In system idle state, within the time set in the operating conditions no any operation, system turn to suspend state.
Adjusting the Hand Strip
The MT70 Series handstrap is attached to the bottom of the terminal. Adjust the hand strap to increase comfort when
holding the terminal for extended periods of time.
Indice
Altri manuali Newland Registratore di dati
Newland
Newland NLS-PT30 Series Manuale utente
Newland
Newland NLS-NFT10 Manuale utente
Newland
Newland CL-M10 Manuale utente
Newland
Newland NLS-MT90 Manuale utente
Newland
Newland NLS-N7 Manuale utente
Newland
Newland NLS-MT95 Manuale utente
Newland
Newland NLS-NFT10 Manuale utente
Newland
Newland NLS-N7L Manuale utente
Newland
Newland NLS-MT65 Manuale utente
