NewTeam 902-T Istruzioni per il montaggio
Installation Instructions
and User Guide
PLEASE KEEP THIS BOOKLET
FOR FUTURE REFERENCE
NEWTEAM 902-T
THERMOSTATIC MIXER SHOWER
DEAR INSTALLER WHEN YOU HAVE READ THESE INSTRUCTIONS
PLEASE ENSURE YOU LEAVE THEM WITH THE USER
IN THE EVENT OF ANY QUERY PLEASE CONTACT
THE NEWTEAM CUSTOMER HELPLINE
Tel : 01536 264 012
Product Features
1NEWTEAM 902-T SHOWER VALVE
NewTeam 902-T
902-T
Contents
2
NEWTEAM 902-T SHOWER VALVE
Please read this booklet carefully and ensure a competent person undertakes the
installation.
Note: Following the headings in sequence will guide you through the installation
and operation of your NewTeam 902-T Mixer Shower.
INTRODUCTION
• Plumbing
CLEANING
ADJUSTING MAXIMUM TEMPERATURE
•902-T Mixer Valve
FITTING YOUR SHOWER
•Important Notes
•General
•Fitting the Shower
•Fitting the Riser Rail
Refer to back cover for Guarantee, Customer Service and Replacement Parts Policy.
In the event of any query regarding installation please contact the NewTeam Customer
Service Department
Tel: 01536 264 012 • Fax: 01536 409 201
In line with our policy of continual product development the specifications may be
varied and product design altered. We reserve the right to depart from the details
given in this manual without prior notice.
3
Pages
4 - 7
8
9
Installation and Operating Instructions
for NewTeam Thermostatic Mixer Shower
• 902-T
TROUBLESHOOTING 9
SPARE PARTS LIST 9
GUARANTEE 10
Introduction
3NEWTEAM 902-T SHOWER VALVE
902-T
The 902-T shower valve is thermostatically controlled.
The NewTeam 902-T Mixer Valve is suitable for the following:
•High Pressure systems to a maximum of 8.0 Bar (50 Metre Head).
•Low Pressure systems with a minimum pressure of 0.1 Bar
(1 Metre Head).
•Pumped Pressure.
•Mains Pressure.
Ideally the supplies should be independent of any other draw offs (e.g.
bath/basin taps).
The Thermostatic Valve includes a Temperature Limit Stop which is
pre-set at approximately 38˚C thus preventing accidental selection of
a shower temperature which is too hot.
If the minimum operating pressure cannot be achieved or you wish to
improve the performance of your shower, NewTeam Booster Pumps
are available.
IMPORTANT:
When connecting pipework do not solder within 300mm (12”) of the
valve or expose parts to excessive heat.
NOTE - That at temperatures above 65ºC air can be expelled from the
water, which can cause poor performance, particularly with pumped
systems, where damage to a pump could occur.
Plumbing - Fig 1
Please ensure compliance with all Water Supply (Water Fitting) Regulations,
paying particular attention to Clause 15 in Water Regulations, when connecting
directly to incoming cold water mains.
The Mixer Valve must be sited to provide easy access for use and maintenance.
Install non-restrictive full flow isolating valves on the hot and cold supplies to the
Mixer Valve.
Ensure the Mixer Valve is not positioned in an area subject to freezing.
Make the connection into the hot water supply pipe from the cylinder ensuring
that it is the first draw off on the vertical pipe below the expansion pipe tee. If this
is not possible a direct connection must be made from the hot water cylinder with
an Essex flange.
The cold water supply should be taken directly from the cold water storage tank
positioned 60mm below the cold connection which feeds the hot water cylinder.
Hot Water Tank
Cold Water Storage Tank
1m. (39”) min.
Fig 1 - Typical Gravity Shower Installation
1 Metre
Min.
60mm
Mains
Water
Supply
Fitting Your Shower
4
NEWTEAM 902-T SHOWER VALVE
•The hot and cold feeds must be at nominally the same pressure. The valve must
not be fed from a low pressure (gravity system) hot supply and a mains pressure
cold supply.
•All pipework should be as short and direct as possible, using swept bends rather
than elbows where practical, to avoid trapping air. Do not tee off the upper surface
of a hot water pipe, especially near to a hot water cylinder, as this will often
contain air bubbles which will adversely affect the operation of the valves. Where
the shower is fed from a gravity system the use of 22mm diameter pipework is
strongly recommended.
•The combination boiler or gas multipoint boiler must be capable of raising the
temperature of 8 litres/min of incoming cold water by 45ºC. This requires a boiler
rating of 25kW (85300 Btu/h).
•The valves must be installed with the outlet pointing downwards, the HOT water
coming in on the left and the COLD on the right as you view the shower on the
wall. The valve will not operate if the connections are reversed.
IMPORTANT:
Modern solder fluxes are extremely corrosive and can damage the valves. It is
essential that all pipework is thoroughly flushed through before connecting the
valve. This is so that flux, debris and swarf, which could permanently damage the
valve, are removed from the pipes.
•Plan the whole installation before you start. Cut the necessary pipework to length,
assemble and offer up to the installation before making and soldered joints.
•Carry out any cutting with a pipe cutter in preference to a hacksaw, to minimise
swarf. Always remove sharp edges.
Important Notes
Cold
Hot
Mixer
Fitting Your Shower
5NEWTEAM 902-T SHOWER VALVE
General:
IMPORTANT
THE 902-T MIXER SHOWER IS HELD IN POSITION BY THE PIPEWORK. IT IS
ESSENTIAL THAT THE PIPEWORK IS RIGIDLY SUPPORTED CLOSE TO THE VALVE.
A CONCEALED WALL MOUNT FIXING IS INCLUDED WITHIN THE SHOWER BOX.
PLEASE REFER TO PAGE 6 OF THIS MANUAL.
The NT902 should only be fitted where water supply pipes are behind a panel or
studwork wall.
This method of fixing requires good access behind the wall or panel.
•Offer up the valve to the wall and mark the required positions of the hot and cold
inlet connections. When positioning the valve make sure to take into account the
intended position of the accessories riser rail.
Ensure there are no services such as gas, water pipes, electrical or telephone
cables beneath the surface of the wall before drilling.
•On plasterboard (studwork) or panel walls, make two holes on 150mm centres to
accept the 1/2”BSP end fitting (see Fig. 3).
•On an internal rendered brick or block wall, drill two 23mm diameter holes on
150mm centres with counterbores to accept the 1/2”BSP end fitting. If 15mm
pipework is used, drill 16mm holes (see Fig. 3).
Cut two pieces of pipe, equal in length to the thickness of the wall plus an allowance
for connection at the rear of the wall, terminate the pipework using a 15mm to 1/2”
BSP, or 22mm to 1/2”BSP female straight tap connector to suit the pipe diameter
used. (The tap connector should include a rotational hexagon nut and washer).
Tighten the 1/2”to 3/4”BSP ‘dog leg’connector to the pipework, loosely fit the two
cover plates half way along the 3/4”BSP thread.
Temporarily block the open ends of the pipework and pass through th
wall until the cover plates are hard against the wall, fit the pipework at the rear of the
wall and secure rigidly, ensuring the two outlets are level and the centres match
those of the valve inlets.
•Flush out the pipework and fit the valve with the outlet
connection downwards, without cover plates and check the
system for leaks.
•Refit cover plate.
•Screw the valve to the pipework ensuring the washer and
filter are inserted, then fully tighten.
•Adjust the cover plates to take up any slack and stiffen the
assembly.
Note: If the non-return valves have to be removed at any time,
please note the bushes are Left hand thread
NB: Hot on the left, cold on the right. Fig 3 - To install on a panel or studwork wall
Fig 2 Fitting Your Shower
NB: The following instructions are for fitting the shower without the
installation bracket (Fig 3).
6
NEWTEAM 902-T SHOWER VALVE
Fitting The Shower
NB: The following instructions are for fitting the shower with the
installation bracket (Fig 4).
The NT902 should only be fitted where water supply pipes are behind a panel or
studwork wall.
•Identify all components and check for completeness, particularly before
arranging fitting.
•Fix the mounting plate to the internal wall or studding using suitable fixings
(not supplied). Use a spacing batten or similar as necessary. Connect the hot and
cold water supplies using 15mm copper pipe with the nuts and olives (supplied).
Supplies can come from above or below making sure Hot is on the left and
Cold is on the right when viewed from the front.
•Finish the wall and push-fit the shrouds as shown. Note! A small bead of silicon
sealant between the wall finish and the spigot diameter under the shroud should
prevent any moisture entering the wall.
•Fit the mixer body to the 3/4”BSP mounting spigots using the large sealing
washers supplied with your fitting.
Fig 4 - To install using installation bracket
Fitting the Riser Rail
7NEWTEAM 902-T SHOWER VALVE
Before proceeding with fitting the rail, identify each of the itemssupplied using
the illustration.
The slider must not be removed from the rail during fitting. The top of the slider has
a smooth profile, whereas the underside has a recess revealing the grooves on the
handset holder.
Fit the rail through the friction sleeve on the soap/gel dish with the sleeve towards
the lower end of the rail.
Fit the rail ends onto the ends of the rail.
Position the rail on the wall, bearing in mind the heights of people
likely to use the shower, and mark the wall to indicate the upper and lower fixing
screw positions. Drill the wall at one of the marked fixing positions using a 6 mm drill.
Loosely fix the appropriate rail end and check that the other fixing screw mark is in
the correct position.
Secure the rail to the wall. Ensure that the rail is vertical before finally tightening both
fixing screws.
Fit the rail end caps.
When fitting the hose, it should pass through the centre hole of the soap dish.
NOTE - The hose nut, and not the handset handle, fits into the slider, and the slider
moves more freely on the rail, if gripped next to the rail rather than at the handset.
Shower Rail Kit - Fig 5
No Part Description
1 Rail end
2 Rail end caps
3 & 4 Rail with slider attached
5 Soap dish
Rail fixing screws &
wall plugs
Fig 5
•These mixer valves have been calibrated at the factory using
balanced pressure hot and cold supplies and a hot water supply
temperature of 65ºC.
•When the installation conditions of the mixer valve are different to
the factory settings, the temperature of the mixed water obtained
from the mixer valve may not correspond exactly with the
temperatures shown on the valve.
If required, the valve can be adjusted to ensure that the indicated temperature
is the same as the temperature obtained from the mixer. To do this, carry
out the following steps:-
1. Rotate the temperature control knob so that the water
issuing from the mixer is at 38ºC.
2. Without moving the temperature control knob, remove the
screw cover from the end of the knob and unscrew the
fixing screw.
3. Remove the control knob, complete with the black ring
containing the temperature figures.
4. Refit the end of the control knob so that the figure 38
corresponds to the indicator on the mixer body.
5. Replace the fixing screw and refit the screw cover.
Note. To set a different temperature at the limit stop position,
follow the above steps but adjust the temperature of the
water to correspond to the limiting temperature required
before the temperature control knob.
Adjusting Maximum Temperature
8
NEWTEAM 902-T SHOWER VALVE
Fig 6
902-T Mixer Valve - Fig 6
Cleaning
9NEWTEAM 902-T SHOWER VALVE
Do not at anytime use bath cleaning liquids, powders or specified non-scratch
cleaners on surface finishes. In order to avoid surface wear on any of your shower
fittings when cleaning, always use a damp cloth. For persistent stains or marks, you
may use a domestic washing-up liquid.
In the unlikely event of a problem, consult the trouble shooting chart below and
follow the order below. If you are unable to remedy the problem, CONTACT YOUR
INSTALLER IN THE FIRST INSTANCE.
Do not attempt any plumbing work unless you are competent to do so.
Cleaning
Troubleshooting
Fault
After installation shower will only run HOT
or COLD.
Low or reduced flow.
Maximum temperature too low or too high.
Solution
Hot and Cold supplies are plumbed in the
wrong way round.
(a) Debris/scale in shower handset. Clean
handset.
(b) Servicing valves not fully open. Open
valves.
(c) Filters partly blocked. Turn off servicing
valves, remove mixer valve and clean
filters.
Re-adjust maximum temperature. See
Adjusting Maximum Temperature.
1. SP-245-0001-CP Rail Ends
2. SP-280-0302-CP Rail & Slider
3. SP-168-0211-CP Zag Handset
4. SP-285-0820-CP Hose
Spare Parts List
Indice
Altri manuali NewTeam Apparecchio per il bagno
